Filter Results By:
Products
Applications
Manufacturers
Transmission
Measures the strength and integrity of a signal carried over wire, fiber or air.
See Also: Transmission Impairment
- Pickering Interfaces Inc.
product
PXI Single 36 Channel MUX, SMB Connectors
40-735-912-S4
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
Modem
CODA-46
Hitron Americas Technologies Inc.
The CODA-46 is an intelligent device that enhances its basic data transmission features with IPv6 support, which makes it especially suitable for the transmission of data based on this protocol.
-
product
Simulators
SAE J1708/J1587
The Au SAE J1708/J1587 simulators (Gen II, V1.00A release) can simulate up to 44 most frequently used Engine/Transmission/ABS parameters, warnings and diagnostic messages. Up to six Engine MID, three transmission MID and six ABS MID can be field configured. All editions can run independently (without personal computer). This family of simulators are designed very easy to use. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
product
LXI WTB Extender
60-984-001
The 60-894 provides a simple an effective method of joining two LXI WTB bus cables together to extend the length of available cables. It is an ideal solution for cable extension where users need to experiment with different cabling solutions without having to totally replace the cables in the system. The 60-894 provides mating connectors for the WTB on each end connected together by a set of accurate differential transmission lines to avoid additional reflections on the cable. The 60-894 is entirely passive and is compatible with the LXI specification.
-
product
Field-installation Type Turbidity Meter (Four-Wire Transmission, Immersion Type)
HU-200TB-IM
HU-200TB-IM connects immersion type turbidity/ MLSS sensor (SS-150) and measures turbidity and SS in activated sludge. The sensor can be immersed directly in the sample water tank. Optimal for turbidity and SS management of wastewater and intake.
-
product
Cable Transmission Tester
SIGNALTEK CT
If you install or maintain data cabling, SignalTEK CT allows you to generate PDF test reports that prove installed links run at Gigabit Ethernet transmission rates.
-
product
4 Wire Earth Resistance & Resistivity Tester
4236 ER
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.● Optical USB to RS-232 data transmission.● The stored data can be transferred to a PC.● 2 optical LEDs are built-in for data transfer.
-
product
photonHiRES
The especially sensitive and high-resolution cameras belonging to the photonHiRES platform are the leading solution when it comes to achieving the highest resolution in industrial machine vision. Even when faced with challenging applications and poor light conditions, the cameras from Photonfocus achieve the best possible results. The robust housings are equipped with an outstanding temperature management system and enable fan-free operation of even large sensors. Moreover, the powerful 10 GigE Vision interface guarantees an optimum data transmission rate and compatibility with a wide range of interfaces.
-
product
Low Cost Microwave Wideband PIN Preamp Receivers
MR21 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
Field-installation Type Dissolved Oxygen Meter (Four-Wire Transmission, Membrane Type)
HD-200
HD-200 connects the DO (Dissolved Oxygen) sensor (DO-1100) and measures the DO in the sample water.The measurement method is membrane type polarography method. It is suitable for monitoring DO in wastewater treatment or aquarium for aquaculture.
-
product
Single-Port Tunable Laser System Source
N7711A
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. All models can reach any wavelength point within their specified wavelength range just like all other Keysight tunable lasers. In this mode, code compatibility with existing test setups based on Keysight's range of full-size and compact tunable lasers is a great asset. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. Likewise, the zero frequency (base channel) of the chosen grid is adjustable. A 12 GHz fine-tuning range allows de-tuning the frequency.
-
product
SUC-A Series Multi-Octave Upconverter
SUC-A
SUC-A Series Multi-Octave Upconverter belongs to our microwave upconverter series that has a high performance and an octave overage by RF signal. Its frequency step is precise and accurate to 10Hz with a variety of IF and signal bandwidth choices.This series of converters is mainly used for electronic countermeasure system, radar system, and satellite communication system. Its excellent phase noise, clutter suppression, and in-band flatness data can provide a transparent RF transmission channel to all videos or data communications. All programming commands can be set through a local panel or through network remotely. SUC-A series microwave upconverter is available in 2U/ 4U sizes.Applications: T&M Systems / Satellite Communications / MIMO / Radar System
-
product
Tes Rreceiver
KH3932
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3932 EM1 test receiver is a fully automatic test receiver and the main tool for EM1 testing. The frequency range of the KH3932 receiver is from 9kHz to 300MHz. Equipped with a power absorption clamp, it can meet the power line disturbance power test. After the artificial power network is configured, the power terminal disturbance voltage test can be carried out. The machine has fast test speed and maneuverability. Strong, stable performance, convenient test data processing and other advantages. The KH3932 receiver uses the USB interface to exchange data with the computer, which makes the transmission speed fast and the bit error rate low. Connect to the computer for testing and use the operating environment familiar to the operator to improve work efficiency.The equipped operating software saves the data of a variety of external equipment, and supports plug and play a variety of external test equipment. The software and hardware are developed by our company. The whole machine uses a fully enclosed structure, and the chassis uses highly conductive materials with good shielding effects. Due to the use of specific technologies and processes, the problem of its own resistance is fundamentally solved. The measurement results are in the international general report format, which can be saved in the computer's hard disk or transmitted through the network, printed out directly, and saved using a USB storage device. The report is rich in content and can be printed directly according to user needs without additional editing.The measurement receiver complies with the requirements of the national standard GBT6113.101 and the international standard CISPR16-1.
-
product
3 DB 90 Degree Hybrid Couplers
KRYTAR's 90 Degree Hybrid Couplers perform many functions, including splitting and combining signals in amplifiers, switching circuits, and antenna beam-forming networks used in a wide range of commercial and military applications. 90 degree hybrids are used in circuits requiring a balanced division of power into two transmission lines with 90 degree separation of phase.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Broadband, Multirange Directional RF Wattmeter
81060
With the Model 81060 Directional Wattmeter you can now measure RF power in 50-Ohm coaxial cable and transmission lines without the need for additional plug-in elements.
-
product
Broadband Communication
PLANET Last Mile Transmission Solution includes technologies such as GPON, GEPON Fiber, VDSL2 and ADSL2+ for various applications. It provides the OLT or CO (central office) which serves as the service provider endpoint of a passive optical network whereas the ONU, HGU and CPE (customer premises equipment) serve as a client endpoint. Its high bandwidth meets the requirements of triple play devices for today’s home entertainment and communications.
-
product
Field-installation Type Simplified Fluoride Ion Concentration Meter(Two-Wire Transmission)
HC-300F
HC-300F is connected to a fluoride ion electrode (1009) to detect free fluoride ions in the sample water.(Total fluorine is not detected.) It is suitable for fluoride ion monitoring in effluent from factories, e.g., those of semiconductor FPD and glass manufacturers.
-
product
Insulation Resistance Meter
AMIC-5005
Insulation resistance measurement - 15TΩ: * 50 - 1000 V, in 10 V steps, * 1000 - 5000 V, in 25 V steps ; Memory of 999 results and transmission to PC ; Measurement of AC and DC voltage and capacity ; Measurement of leakage current ;Function with digital filter
-
product
Field Strength Calibration Probe
Beijing KeHuan Century EMC Technology Co,.LTD
Three-axis omnidirectional 100kHz～6GHz light transmission.
-
product
Copper Telecommunications Test
Noise and transmission problems are constant battles in the best of worlds. With emerging technologies like IP-video over DSL delivered to the customer over existing copper pairs, it's more vital than ever for telephone companies to test and maintain their outside copper plants.
-
product
Synchro Power Amplifiers
SSP
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
-
product
Sound Source And Power Amplifier
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
product
Single Channel Oscilloscope 20M-100MHZ
HDS
Shenzhen Chuangxin Instruments Co., Ltd.
- Auto-scale function- 20 automatic measurements- Bandwidth : 20MHz - 100MHz- USB data transmission supported- Waveform record and replay- Multimeter newly supported SCPI- Rechargeable Li-ion battery (6 hours' backup)
-
product
6U VPX PCIe to XMC Expansion Board
VP69601
LinkedHope Intelligent Technologies Co.,Ltd.
VP69601 is a 6U VPX PCIe to XMC expansion board. Onboard there is a x8 PCIe 3.0 interface, and through a PCIe connector the x8 PCIe 3.0 turns into 2 x8 PCIe 3.0 linking to 2 XMC cards. The PCIe Switch IC on VP69601 supports DMA, so direct data transmission between peripheral cards can be realized.VP69601 can be installed in a standard VPX chassis and work as a peripheral board. VP69601 carries two XMC ports, through which users can expand various functional XMC cards needed.Apart from the traditional Air Cooling design, Linkedhope○R provides a Conduction Cooling version to guarantee working stability of VP69601 in extreme and vibration environment and in an extended working temperature from -40℃ to +70℃.
-
product
Sun Trackers
STR-series
EKO Sun Trackers are very compact, robust, relatively light weight and very power efficient. Inside the Sun Tracker a Harmonic Drive with advanced motion control unit is used on each output shaft. Harmonic drive is a leading drive technology for those application where high precision, durability, low backlash, high transmission ratios and torque is required. Due to its compact design and high transmission ratio small motors could be used to keep the power consumption low.
-
product
Color Mark
Accurately detect color variations using our powerful color mark sensors that provide reliable data transmission via IO-Link.
-
product
Fiberoptics
Antenna Technology Communications, Inc.
The 402LZ is a outdoor/indoor mounted fiber optic transmitter for RF signals in the satellite L-Band or wider frequency range. It accepts a single RF input on coaxial cable and provides a single output for optical transmission. Up to four 402LZ’s may be installed in the ATCi Link4i chassis.
-
product
UIO40-Express Series
UIO-4036
*Supports 10/100/1000 Mbps Auto-Negotiation*2 LEDs on Each Port to Show Link/Active Status and Transmission Speed
-
product
Field-installation Type MLSS Meter (Four-Wire Transmission)
HU-200SS
HU-200SS connects immersion type MLSS sensor (SS-90) and measures MLSS in activated sludge. A wide range (0-2000mg/L)of SS contents can be measured with excellent reproducibility using the near-infrared radiation transmission method. Any of the calibration curves of MLSS, Clay (inorganic mud) and Kaolin may be used as standard substances of SS. If "MLSS" is selected for an activated sludge treatment tank, "Clay" for the precipitation treatment of construction sludge, or "Kaolin" for white mud, a concentration can be obtained closer to an analyzed value.
-
product
Differential Picosecond Pulse Generators
PicoSource PG900 Series
The fast-transition pulse can stimulate a transmission path, device or network with a broad spectrum signal in a single instant. Such a pulse is very useful for many of the high-speed broadband measurements that we need to make; for instance in time-domain reflectometry, semiconductor test, gigabit interconnect and port test and in radar.
