Filter Results By:
Products
Applications
Manufacturers
Switched Mode Power Supplies
Load Current is oscillated on and off regulating ouput voltage.
- Pickering Interfaces Inc.
product
PXI 10A Power MUX, 1-Bank, 16-Channel
40-661-103
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
product
Analog Optical Power Meter - MATRIQ
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
product
Optical Power Meter - PXI
Power 1400 Series
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
product
Power, Patchcord, Receiver, 36", Micro Power, 12 AWG White, Single Ended (22 Amps)
7-252912000-036
Power, Patchcord, Receiver, 36", Micro Power, 12 AWG White, Single Ended (22 Amps).
-
product
High-density Optical Power Meter.
Power-1410
Quantifi Photonics’ Power-1410 optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 1250 to 1650 nm. It provides unrivalled channel density with up to 288 parallel channels in a single 1U rack-mountable instrument.
-
product
PICMG 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI 8HP 250 W Power Module
cPS-H325/AC
*PICMG® 2.11 CompactPCI® Power Interface compliant*3U CompactPCI® 8HP form factor*PICMG® 2.11 47-pin CompactPCI® in-rack power module interface*250 W DC output
-
product
Intelligent Power Monitor
iPM
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
product
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps)
7-235916000-036
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps).
-
product
Power, Patchcord, Receiver, 72", High Power, 2 AWG, Double-Ended
7-221902688-072
Power, Patchcord, Receiver, 72", High Power, 2 AWG, Double-Ended.
-
product
Digital Power Meter
Digital Power Meter is designed for single-phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits, the 66200 uses state-of-the-art DSP digitizing technology.
-
product
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-222902688-036
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
product
Programmable Linear DC Power Supply, 3 Output, 0-32V/0-3.2A, 2.5V/3.3V/5V/3.2A
T3PS3000
Teledyne Test Tools new T3PS3000 is a Linear Programmable DC Power Supply with a 4.3 inch TFT LCD display. It has three isolated outputs: two adjustable channels and one selectable channel from 2.5 V, 3.3 V, and 5 V with output short and overload protection for each channel. Support for series and parallel operation of the two main channels extends its flexibility beyond the standard specification. The T3PS3000 features include programmability via USB or LAN, a graphical display of power waveforms, and the high resolution numeric display of voltage and current. Typical users are Education, Production, and Design and Development.
-
product
Power, Patchcord, ITA, 72", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-222902688-072
Power, Patchcord, ITA, 72", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
product
5VA Reference Supply, DC input
PS5410C-16
The PS5410C-16 is a 5VA AC Reference Power Supply, available with many transformer isolated output voltages at different frequencies. Input power is either 12 VDC or 15 VDC. The standard 15 pin "D" connector simplifies interconnection to other equipment.
-
product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
*PICMG® 2.11 CompactPCI® Power Interface compliant*3U CompactPCI® 8HP form factor*PICMG® 2.11 47-pin CompactPCI® in-rack power module interface*250 W DC output*Active PFC (Power Factor Correction) meets IEC1000-
-
product
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-251414000-036
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
product
Power, Patchcord, Receiver, 36", High Power, 2 AWG, Single -Ended (150 Amps)
7-221902000-036
Power, Patchcord, Receiver, 36", High Power, 2 AWG, Single -Ended (150 Amps).
-
product
Optical Power Meters
Fast monitoring of optical signal power from -60 to +10 dBm across 750 – 1700 nm wavelengths. The 1500 Series power meter offers logarithmic analog output which is ideal for active fiber alignment.
-
product
DC/DC Power Supply
ISM-DC-AT512-P
The ISM-DC-AT512-P is a dual output, DC/DC power supply designed for small form factor embedded systems. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/COTS, security, solar-powered, and telecommunications.
-
product
Inline Optical Power Meter - MATRIQ
The Power 1600 Series optical power meter provides quick and accurate inline power monitoring from -50 dBm to +20 dBm with 1, 2 or 4 channels in a compact form factor.
-
product
Power Monitor, AC- or DC-Powered
109
NAI’s 109 is an AC- or DC-Powered Power Monitor used to monitor voltage, frequency, and phase characteristics of single- or three- phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.The 109 monitor provides three separate control circuits and output relays indicating the condition of each line characteristic. It is ideally suited for rugged defense and industrial applications.
-
product
Optical Power Meter - MATRIQ
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
product
25-Watt AC/DC Power Supply
Model 56GS1
NAI’s 56GS1 is a 25 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
product
500-Watt AC/DC Power Supply
56TS1
NAI’s 56TS1 is a 500 Watt AC/DC Power Supply that accepts a 3Ø AC input or a +270 VDC input. This COTS unit provides full-power output power at a baseplate temperature of +85° C.
-
product
300-Watt AC/DC Power Supply, 6U VME
Model 56SQ2
NAI’s 56SQ2 is a 300 Watt AC/DC Power Supply that uses two slots in a standard VME chassis. It is conduction-cooled through the card edge/wedgelock. This power supply accepts either a single- or three-phase input and provides up to 5 standard VME outputs plus standby at 300 Watts. It is designed for VME and general purpose applications. An onboard microcontroller allows for design flexibility.Standard features include continuous Background Built-in-Test (BIT); remote error sensing; holdup time; and protection against transients, overvoltage and short circuits. Options such as power fail warning, vibration testing, over-temperature monitoring and shutdown, current share, and extensive signaling (including ANSI/VITA) are available.
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-251414000-072
Power, Patchcord, ITA, 72", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
product
PICMG® 2.11 47-pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/110
*PICMG® 2.11 CompactPCI® Power Interface compliant*Internal OR-ing Diodes for N + 1 redundancy*PICMG® 2.11 47-pin CompactPCI® in-rack power module interface*250 W DC output*Active PFC (Power Factor Correction) meets IEC1000-3-2 Harmonic Correction
-
product
1,000 Watt AC/DC (High Voltage Output) Power Supplies
56XS2
NAI’s 56XS2 is a conduction-cooled, 1,000 Watt AC/DC Power Supply that converts a 3-phase, AC input into a single HIGH VOLTAGE +270 VDC output at 1,000 Watts.
-
product
Multi-Channel Power Module
67394
The 67394 Multi-Channel Power Module is a new generation of compact, stable and high reliability AC to DC power supply that can test the small size panels. It has multiple power sources with voltage/timing adjustable functions, protection functions and measurement circuits. Its modular design can work with FPD tester and PG card to provide standard power source for testing the panels.
