Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
product
Microcontrollers
32-bit Qorivva microcontrollers based on PowerArchitecturetm e200 cores, that can run up to 264MHz. These devices include flash and RAM memory, as well as a number of external interfaces making them suitable for Aerospace & Defense of applications.
-
product
Analog Output Module, 16-bit
IP235A
IP235A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Acute 4GS/s 68 Channel Logic Analyzer With 32Gb Memory
Acute LA3068B+
*LA3000E+/B+ series logic analyzer*PC-based*68 / 136 channels*USB 3.0 interface, 12V power adaptor*4GHz Timing Analysis / 250MHz State Analysis*32Gb RAM*Active Probes*Logic, State, Protocol triggers
-
product
Touchscreen Panel 1.9GHz PC for Harsh Environments
PPC65B-1x series
Advanced IP65-rated Panel PC delivering high reliability and an extended operating temperature range in a thin, fanless design. The PPC65B series offers a rugged design for extreme environments and industrial IoT applications ranging from -20ºC to +70ºC. 1.9 GHz Quad-Core Intel® Atom™, E3845 processor, Up to 8 GB of RAM, Supports Linux, Windows 10 Operating Systems, Fast Graphics at High Resolutions • Five-wire resistive touchscreen • Resolution: 1024 x 768 / 1280 x 1024; 5 screen sizes 10.4" - 19".
-
product
Gage EXpert FPGA Realtime Data Streaming
eXpert Stream-to-Analysis
All Gage PCI Express CompuScopes are able to Stream waveform data through the PCI Express bus directly to PC RAM. By contrast, older Memory Mode operation required storage of data in dedicated digitizer memory prior to data transfer. Streaming provides two distinct advantages over Memory Mode. First, Streaming may overcome the acquisition time limit imposed by the volume of dedicated digitizer memory. Second, in Streaming Mode, the user does not need to await completion of waveform acquisition before accessing the resulting waveform data, which is necessary in Memory Mode.
-
product
Memory Tester
RAMCHECK
RAMCHECK is our most advanced memory tester and is the latest in our product line. Highly modular and user friendly, it redefines the capabilities of an affordable and portable ram checker.
-
product
VME / VSB Module
ADM-42M
The AD42M Data Acquisition Module provides high performance 14-bit digitizing of analog signals for VMEbus applications. The AD42M accepts 4 differential analog inputs via front panel miniature SMC connectors. The AD42M utilizes a signal processor to acquire and store data samples. The AD42M is able to direct the data samples to local static RAM or VSB.
-
product
MIL-STD-1553 Two-Channel PCI Board
BRD1553PCI-2
The P-Orchestra™ is a two-channel MIL-STD-1553B PCI board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. The board can be used as a hardware and software development kit for IP cores. P-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 8K word of internal RAM for Module 0 and 16K word of internal RAM for Module 1. Software drivers for Windows, Linux and QNX, along with high-level API, are available to ease application development.
-
product
PCI Data Acquisition Boards
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
product
Fibre Channel Simulyzer™ Products
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
product
3-in-1 Analyzer: Logic Analyzer, Protocol Analyzer, Simple DSO
MSO2216B+
3-in-1 Analyzer : Logic Analyzer, Protocol Analyzer, Simple DSO• PC-based, USB3.0 interface• 8 / 16 Channels(display digital and analog waveforms of the same channel)• Digital Inputs : 2 GHz Timing, 200MHz State Analysis (Max.)• Analog Inputs : 200 MS/s (Max.), Bandwidth 40 MHz• 8 Gb Memory (Max.)• PC RAM storage for streaming mode• Utility model patent of Taiwan number M601827
-
product
RFID Chamber
– 80dB RF shielded enclosure (inside dim.- 5’ high x 5’ wide x 7’ long)– Fabrication, Construction, and Transportation– Free standing shielded enclosure design including structural support system– Enclosure will be installed over a continuous 1/8″ dielectric underlay and polyethylene vapor barrier– Modular wood-core panel construction– Bulkhead connector panel – (1) 12” x 12”– RF shielded doors – (2) 2’ x 2’– One (1) Antenna Sinclair Model SP-440-SF2SNF– Shield test per IEEE –STD 299- supersedes MIL-STD-285 (Tested @ 1 GHz)– RAM
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3016-16
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
product
Module Spectrum
nRF52820 Series
Nordic nRF52820 solutioin features an Arm Cortex-M4 processor with 256 KB Flash and 32 KB RAM. Supports SPI, UART, I2C and USB interfaces
-
product
SMARC V1.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio, CAN, MIPI And PCAM
SCM120
*SMARC 1.0 (82 x 50 mm)*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android 4.3*Audio
-
product
Intelligent Interface Card
IIB-1553-PCI-2C
The IIB-1553-PCI-2C provides an intelligent interface card for two serial, dual redundant MIL-STD-1553 data buses and the PCI bus. The card supports 1553A, 1553B, McAir and STANAG 3838 variants on a single card. The IIB-1553-PCI-2C provides concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Two independent variable amplitude dual redundant 1553 interfaces are provided, each with2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Register
Signal Recording Program
The signal recording program is used for continuous real-time recording of signals coming to the input channels of measuring instruments. For convenient signal processing, the program provides an unlimited number of records for text and voice comments. Signals can be recorded in the bounded or direct RAM buffer with further copying to a storage unit. This recording mode allows to record any unknown event with historical data.
-
product
Microprocessor System Tester
IST-6700
IST Information Scan Technology, Inc.
The IST 6700 is a low cost, stand-alone test instrument that provides a wide range of automatic and manual features for troubleshooting microprocessor-based circuit boards. It employs CPU emulation with low cost CPU personality pods to attach to or replace the resident CPU. With stored "Known Good" test data, the 6700 can provide fully automatic functional tests to check the system RAM, ROM, control signals, address, and data bus plus the measurement of the CPU clock frequency and supply voItage.
-
product
PXIe-6571, 1-Slot, 100 MVector/s PXI Digital Pattern Instrument
786320-01
1-Slot, 100 MVector/s PXI Digital Pattern Instrument - The PXIe‑6571 is designed for semiconductor characterization and production test. It includes the Digital Pattern Editor for configuring pin maps, specifications, levels, timing, and patterns. It also includes debugging tools … like Shmoo, digital scope, and viewers for history RAM, pin states, and system status. The PXIe-6571 requires a chassis with 82 W slot cooling capacity, such as the PXIe-1095.
-
product
Module Spectrum
nRF52833 Series
Nordic nRF52833 solutioin features an Arm Cortex-M4 processor with 512 KB Flash and 128 KB RAM. Supports SPI, UART, I2C,I2S, PMD, PWM, ADC, NFC and USB interfaces
-
product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
Portable Interface Unit
1553-USB-PIU
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-16-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
3 Function Slot MOSA Nano Aircraft Interface Computer (AIC)
NIU3A-AIC-01
NIU3A-AIC-01 is a Modular Open Systems Approach (MOSA) Aircraft Interface Computer with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
product
Midi Logger`
GL980
*8CHHigh speed simultaneous sampling*Includes 500 V measurement with 16-bit A/D converter*Equipped with true-rms measurement*Large built-in RAM (4 M sampling/ch) and built-in Flash memory (4 GB)*Large easy-to-read 7-inch LCD
-
product
3 Function Slot MOSA Nano Data Concentrator Unit (DCU)
NIU3A-DCU-01
NIU3A-RDC-01 is a Modular Open Systems Approach (MOSA) Data Concentrator with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
product
Intelligent Interface Card
IIB-1553-ISA
The IIB-1553-ISA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-ISA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multilevel triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable.The board is supplied with C drivers in source code and Windows menu driven software as standard.
