Filter Results By:
Products
Applications
Manufacturers
-
product
3D Sound Intensity Analysis Software
DS-0225A
Finding out the position where the noise is occurring, and grasping the state of acoustic propagation are important ways to find effective noise countermeasure or improvement of acoustic environment.
-
product
Dynamic and Fatigue Testing Systems
Instron offers an extensive range of fully-integrated dynamic and fatigue testing systems from 1000 N up to 5000 kN. Incorporating servohydraulic, servo-electric and linear motor technologies, these test instruments cover a broad range of fatigue, dynamic, and static testing applications. These applications include high-cycle fatigue, low-cycle fatigue, thermo-mechanical fatigue, fracture mechanics, crack propagation and growth studies, fracture toughness, bi-axial, axial-torsional, multi-axial, high strain rate, quasi-static, creep, stress-relaxation, and other types of dynamic and static tests.
-
product
Radar Target Repeater
Series 8000
The Eastern OptX Series 8000 Radar Target Repeater is a portable, variable delay and propagation loss system designed for radar testing and alignment. The repeater may be remotely programmed in the field for dynamic operation. When connected to a user specified antenna the repeater can provide delays of up to 500 usec with a fixed delay, multiple discrete delays, or a progressive variable delay with amplitude control The Series 8000 features ultra wide bandwidth, low loss, high isolation, low noise figure, and high dynamic range.
-
product
UMTS / GSM Tester
manufacture a range of items that can be used in UMTS and or GSM propagation testing. These products have been designed against customers requirements.
-
product
Mobile Cable Fault Location System
BAUR Syscompact 4000
BAUR Prüf- und Messtechnik GmbH
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
-
product
Predicting Microwave and RF Designs Virtually
RF Module
The RF Module is used by designers of RF and microwave devices to design antennas, waveguides, filters, circuits, cavities, and metamaterials. By quickly and accurately simulating electromagnetic wave propagation and resonant behavior, engineers are able to compute electromagnetic field distributions, transmission, reflection, impedance, Q-factors, S-parameters, and power dissipation. Simulation offers you the benefits of lower cost combined with the ability to evaluate and predict physical effects that are not directly measurable in experiments.
-
product
Compact Tension Grips
These compact tension grips are for plane-strain fracture toughness tests of metallic materials. Fracture toughness testing involves applying static loads to a notched sample to investigate brittle crack propagation and fracture conditions.
-
product
Satellite and Aerospace Channel Emulation Toolset
S8825A
Satellite, aerospace, and airborne radio link testing with realistic wireless propagation conditions. 5G NTN test support with satellite connection from mobile phones. Interconnecting networks for full end-to-end system testing.
-
product
Radar Target Generator
Series 1100
The Eastern OptX Series 1100 Radar Target Simulator is a true propagation path replicator. The Series 1100 receives the signal transmitted from a radar system and adds the round-trip propagation delay associated with the target distance. That signal is then output to the radar receiver. The radar I/O may be connected directly to the Series 1100 or detected and transmitted using user specified antenna. For a moving target the system will add the appropriate Doppler shift associated with the target speed and radar frequency. The Series 1100 is broad band with ranges up to 40 GHz and with a dynamic range of over 100 dB.
-
product
Optical VSF Sensors
The optical Volume Scattering Function(VSF) is an ‘inherent optical property’ of water that is used by optical oceanographers to predict light propagation, image degradation, remote sensed ocean color, biological environment etc. in water.
-
product
Channel Emulator/Fading Simulator
The channel emulator/fading simulator is a measuring instrument for reproducing the actual radio wave propagation environment of mobile communication.It reproduces the fading environment defined by 3GPP and virtual environment of multiple channels such as MIMO, HetNet.It will contribute to improving development and verification efficiency of the latest mobile communication system such as 5G NR, LTE-Advanced and IoT.
-
product
Nuclear Event Detectors
DDC Connectivity Power Controls
DDC's radiation-hardened, hybrid, Nuclear Event Detectors (NED) sense ionizing radiation pulses generated by a nuclear event, such as the detonation of a nuclear weapon, and rapidly switches its output from the normal high state to a low state with a propagation delay time of less than 20ns. The active low Nuclear Event Detection signal (NED) is used to initiate a wide variety of circumvention functions, thus preventing upset and burnout of electronic components. The NED output is also used to initiate both hardware and software recovery. This high-speed, 14-pin hybrid detector is used in electronic systems as a general-purpose circumvention device to protect memory, stop data processing, and drive power supply switches as well as signal clamps.
-
product
Beacon Transmitters for Radio Amateurs
Is a radio beacon, whose purpose is the investigation of the propagation of radio signals. Most radio propagation beacons use amateur radio frequencies. They can be found on LF, MF, HF, VHF, UHF, and microwave frequencies. Microwave beacons are also used as signal sources to test and calibrate antennas and receivers
-
product
Channel Replicator
Series 7000
The Series 7000 System is a multi-radio test network which replicates the propagation path of real-world applications. With complete bi-directional capability radios may operate in full duplex mode at distances up to 150 nautical miles.
-
product
LTE Networks
PBE offers secure and reliable wireless solutions for critical mining and tunnel construction operations. Complete end-to-end private LTE networks provide unified infrastructure for underground applications with different QoS, bandwidth and latency requirements.PBE private LTE allows customization of the capabilities of public cellular LTE networks and scale it according to the size and requirements of the particular mine. P-LTE networks provide both human and machine communications on a single, seamless and extendable network that offers long ranges of propagation. In addition to the standard telemetry (air quality monitoring, ventilation management, pump control, belt control, fire suppression, evacuation alerting stations, etc.) LTE networks provide a gateway for:- Voice Communications (VoLTE, VoIP, Push-to-Talk)- Video Communications- CCTV- Internet Access- LAN Access- Real Time Machine Control- Fleet/Asset Management- Access Control/Localization- Automation- Collision Avoidance- Remote Diagnostics
-
product
Distance Measuring Equipment (DME)
MS 2002
Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures distance by timing the propagation delay of UHF radio signals. The DME system is composed of a UHF transmitter/receiver (interrogator) in the aircraft and a UHF receiver/transmitter (transponder) on the ground. The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and the ground station replies with an identical sequence of reply pulse-pairs with a precise time delay (typically 50 microseconds). The time difference between interrogation and reply minus the 50 microsecond ground transponder delay is measured by the interrogator's timing circuitry and translated into a distance measurement in nautical miles which is then displayed in the cockpit.
-
product
Half, Full Bridge & Three Phase Drivers
Renesas' half-bridge (h-bridge), full-bridge and three-phase drivers handle voltages up to 100V, with industry-leading gate rise and fall times and exceptional input-to-output propagation delay performance.
-
product
Transmitter
TX2440 MmWave
The unique propagation characteristics of 5G mmWave signals require upfront testing with a Continuous Wave (CW) transmitter to ensure proper network design. PCTEL’s portable, high-power TX2440 mmWave Transmitter propagates mmWave signals at any venue for convenient testing with PCTEL® scanning receivers.
-
product
Field Strength Meters
The FSM series of field strength meters will measure the strength of a RF signal appearing at its input from +20 dBm to -110 dBm for wide bandwidth models and +10 dBm to -120 dBm for narrow bandwidth models. The RF strength will be displayed on an LCD display to an accuracy of ±3 dB over the entire 130 dB dynamic range. A matching field signal generator is also available to act as a signal source for propagation studies.
-
product
Timing Measurement Unit
TMM200
The TMM200 is a resource available for measuring such parameters as propagation delays, rise time, fall time and any other time-related parameter. Because of its wide input levels, the TMM200 is an instrument well suited to test both digital an analog devices.
-
product
5G Radio Test Set
Operating from 20 to 40 GHz, two radios may be connected to the system allowing full duplex operation. Each radio may operates over identical Air Interface with uni or bi-directional multipath. The delays between radios may be varied from 0 to 1 mile in 5 foot steps with propagation loss control. The 2040+ creates a variable test range right in your lab. It can be used as a design aid and as a test tool for new modulation and encryption schemes prior to expensive and time consuming field testing.
-
product
Correction in Gate-level Simulations Software
Verix SimFix
Verix X-Pessimism correction system (SimFix) enables accurate gate-level simulations (GLS) that are necessary for a thorough verification sign-off. Inaccurate simulation is caused by the propagation of pessimistic unknowns (e.g. X’s) in netlist designs. SimFix uses mathematical methods to identify conditions under which pessimism can occur, and to determine the correct value when those conditions occur. It then generates auxiliary SimPortal files that, when used in simulation, will detect and correct pessimism so that the simulation accurately models real hardware. Without SimFix, GLS verification is compromised by inaccurate random initialization or costly synthesis switches, neither of which is foolproof and often still requires long and laborious gate-level debug.
-
product
*Beam Propagation Analysis
M²
M², or Beam Propagation Ratio, is a value that indicates how close a laser is to being a single mode TEM00 beam, which in turn determines how small a beam waist can be focused. For the perfect Gaussian TEM00 condition the M² equals 1. M² cannot be determined from a single beam profile measurement. The ISO/DIS 11146 requires that M² be calculated from a series of measurements. M² is measured on real beams by focusing the beam with a fixed position lens of known focal length, and then measuring the characteristics of the artificially created beam waist and divergence. We have a number of solutions for the measurement of M² ranging from simple manual processes to fully automated dedicated instruments, depending on the frequency of the need to measure M² of lasers and laser systems.
-
product
Time Domain Reflectometer / TDR
For testing cables and interconnects, we offer the ideal tool: A time domain reflectometer (TDR). Time domain reflectometry/transmission can be used to test network return loss (S11), propagation loss (S21), and crosstalk.Moreover, it can provide the impedance profile of an electrical channel. MultiLane supplies semi-automated solutions for the testing of direct-attach cables and TIAs.
-
product
1204a/1204a-mc Digital Signal Distribution
Precise Time and Frequency, Inc.
The ptf 1204A Digital Signal Distribution unit is a flexible platform used for distribution of various pulse formats (ex. 1 PPS, 1 PPM, 10 PPM, etc). The ptf 1204A will also distribute digital timing signals such as IRIG-B DCLS format. In order to cater for a wide range of input pulse frequencies, the ptf 1204A design utilizes a CPLD with jumper selectable alarm delays tocorrectly alarm on the various pulse frequencies. The unit reproduces precision pulse input signals with the minimum of propagation delays.
-
product
M2 & BPP Systems
The M2 factor wil define the beam propagation characteristics compared to ideal Gaussian beam propagation. According to ISO Standard 11146 rightfully offers the laser beam characterization as "M2 times diffraction limited beam", as such, a perfect beam will have an M2 of 1. 1 will be the best achievable value and no beam could have an M2 less than 1. Our conceptual design is based on sub-assemblies allowing to change the sensing head in the M2 device, offering multiple wavelengths heads up to 2.7 microns from deep UV (knife-edge technology) and camera based technology with built-in automatic filter wheel for adjustment. For focused beams, the same measuring head could be attached to a device for meauring highly divergent or highly convergent beams - FocusGage-BA, wherein the Laser Analyzing Electronic Autocollimator offers the capability of divergence measurement with Coming Soon M2 definition. M2Beam is the cornerstone of those measuring devices.
-
product
Ray tracing and Laser Simulation / Cavity Design Software
LasEasy V1.0
LasEasy software is the professional software for simulating and designing solid-state laser cavity, optical amplifier system, and parametric OPO systems. It can also simulate the laser light propagation in both horizontal and vertical (sangital and tangitial) planes.
-
product
RF Test
RF is short for radio frequency. RF is any frequency within the electromagnetic spectrum associated with radio wave propagation. When an RF current is supplied to an antenna, an electromagnetic field is created that then is able to propagate through space. Many wireless technologies are based on RF field propagation. These frequencies make up part of the electromagnetic radiation spectrum.
-
product
X-Design and Verification System
Ascent XV
The Ascent X-design and verification system (XV) prevents, detects and isolates issues caused by the propagation of unknowns (‘Xs’) in RTL designs, including Xs that occur during power-on initialization and switching between power modes. Early sign-off of X issues eliminates costly, painful gate-level debug, and prevents hidden functional bugs from slipping through to silicon.
-
product
MOSFET Drivers
The bridge driver products handle voltages up to 100V, with industry-leading gate rise and fall times and exceptional input-to-output propagation delay performance. Select parts are available in 4mm x 4mm and 3mm x 3mm DFN packages which meet IPC-2221 creepage and clearance specifications for high-voltage systems.
