Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-118-M62.5-HI
The 40/42-852A-118-M62.5-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
4 Wire Earth Resistance & Resistivity Tester
4236 ER
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.● Optical USB to RS-232 data transmission.● The stored data can be transferred to a PC.● 2 optical LEDs are built-in for data transfer.
-
product
Low Cost Microwave Wideband PIN Preamp Receivers
MR21 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
Broadband Communication
PLANET Last Mile Transmission Solution includes technologies such as GPON, GEPON Fiber, VDSL2 and ADSL2+ for various applications. It provides the OLT or CO (central office) which serves as the service provider endpoint of a passive optical network whereas the ONU, HGU and CPE (customer premises equipment) serve as a client endpoint. Its high bandwidth meets the requirements of triple play devices for today’s home entertainment and communications.
-
product
Fiberoptics
Antenna Technology Communications, Inc.
The 402LZ is a outdoor/indoor mounted fiber optic transmitter for RF signals in the satellite L-Band or wider frequency range. It accepts a single RF input on coaxial cable and provides a single output for optical transmission. Up to four 402LZ’s may be installed in the ATCi Link4i chassis.
-
product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PXI Express
PXIe-DCE
Avionics Interface Technologies
Supports 10/100/1000 Mbit/s Full Duplex EthernetUtilizes SFPs to support both Copper and Optical interfacesUser controlled Ethernet frame transmissions with high precision timing and scheduling
-
product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
product
Amplifiers
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
product
High-Throughput NIR Spectrometers
Acton LS 785
Teledyne Princeton Instruments
The Acton LS 785 is a high-throughput, lens-based spectrograph ideal for NIR spectroscopy. With a fast f/2 optical system with proprietary AR-coated lenses it is optimal for NIR transmission.
-
product
Optical Modulator
Is an Intensity Modulator that is manufactured with Annealed Proton Exchange(APE) process, it features a zero-chirp design and Polarization Maintaining(PM) fiber output. Features 20 GHz E/O bandwidth, a highly linear transfer function and excellent extinction ratio. Applications include digital transmission up to 20 Gb/s, analog RFoF transmission to 20 GHz, optical pulse generation, mode-locked fiber laser and microwave optical link.
-
product
4-Channel Optical Transceiver
QSFP28 AOC
Eoptolink Technology Inc., Ltd.
Eoptolink QSFP28 Active Optical Cable is a 4-channel optical transceiver, which conforms to QSFP28 MSA and works at the rage of 25Gbps per channel. The AOC conforms to transmission speed required by InfiniBand™ EDR, 100 Gigabit Ethernet (100GBASE-SR4) and enables to transmit maximum 100m. Best for close-range high-speed transmission, for example, betweenserver racks, between servers.
-
product
OTDR
AV6416
Hangzhou Softel Optic Co., Ltd.
AV6416 palm OTDR is the newest instrument designed for testing FTTx network. It's mainly used to measure the physical characteristics of optical fiber under test, such as the length、the transmission loss and the splice loss etc.. It can also locate the faults or breaks of optical fiber. It's widely applied in the manufacture, construction and maintenance in optical fiber communication system.
-
product
Fiber Adapter
USB Serial Optical Converter
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*USB bus-powered*Virtual serial interface*Baud rate up to 115kBit / s
-
product
Multi-Wavelength Meter
86122C
With an absolute wavelength accuracy of 0.2 ppm and 0.15 ppm differential accuracy, the new Keysight 86122C Multi-Wavelength Meter belongs in the top class of wavelength meters available for optical communication testing. Its wavelength range of 1270 to 1650 nm covers all fiber-to-the-home, metro and long-haul transmission systems. The instrument can measure the spectra of up to 1,000 laser lines at once, which is more than sufficient for fully populated dense-wavelength-division multiplexed systems (DWDM).
-
product
OTDRs
FX Series
The VeEX OTDR solutions are optimized for today''s optical fiber networks. The FX series is perfectly suited for the challenging outside plant environment and complements the existing VeEX Transmission and Ethernet testing solutions.
-
product
10G DPSK Demodulator
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5,10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systemsutilized in commercial, defense and space exploration markets. The device plays a key role in improvingsignal quality and performance to meet the expanding demand for higher data rates and more complextransmission formats within current and next generation systems without major capital expenditure.Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. The measured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarization-dependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
product
Power Meter
8015 PM
Standard Electric Works Co., Ltd
● Determine the running cost of your appliances.● Measure voltage, current, frequency, watt, power factor, and greenhouse gas emissions.● Optical USB to RS-232 data transmission.● 2 Optical LEDs are built-in for data transfer.● Transferring and showing real-time data to a PC.● Make informed decisions when purchasing appliances and equipment.● Reduce your electricity bill.● Calculate electrical expenses by real, hour, month. ● Can make different kinds of plugs for different countries / areas, such as Type B, E, G, I plugs.....etc.● Data communication function.● Freely set upper and lower limit for V,A,W and alarm when measured value is out of limit.● Backlight function.
-
product
NRZ Bit Error Rate Tester
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
product
Optical Talk Set
FTS100
Shanghai Tarluz Telecom Tech Co., LTD
In some rural site, the mobile phone may be out of service range, if conversation between two operators who are laying down an optical cable for optical network needed. in the situation, Tarluz Fiber Talk Set is essential. With the optical talk sets, the two operators can have talk with each other directly via an intact optical fiber. It is easy and reliable. TARLUZ FTS100 handheld optical talk set with dynamic range of 33dB. The high dynamic range ensures the quality of voice and long transmission distance.
-
product
DCA-X Sampling Oscilloscopes
The DCA-X wide-bandwidth sampling oscilloscopes are in our digital communication analyzer (DCA) family. These are modular platforms that provide accurate and precise measurements of high-speed digital designs from 50 Mb/s to 224 Gb/s. You can configure the DCA-X mainframes by selecting from a variety of plug-in modules that perform precision optical, electrical, and time domain reflection / transmission (TDR / TDT) measurements. Select specific modules to obtain the desired bandwidth, filtering, and sensitivity that match your measurement needs.
-
product
C-Band DWDM Fixed Gain EDFA (FGA-C)
HWA4400 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4400 series is a fixed gain EDFA which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
Miniature Single-Stage Isolators – 780nm And 852nm
AOSense is excited to offer free-space optical isolators at 780 nm and 852 nm. The innovative, small package size enables integration into compact laser sources and amplifiers without sacrificing transmission efficiency. The low external magnetic field enables the isolator to tightly integrate into systems with high magnetic-field sensitivity such as atomic spectrometers, magnetometers, clocks, and cold-atom devices.
-
product
Omnisens Securing Power Cable Integrity
https://www.omnisens.com/uploads/1/2/0/5/120592129/published/omnisens-cobra-logo-white-2014-06-10.png?1546958203
In both underground and subsea cables incipient faults often result in temperature events. Using optical fibers integrated into the power cable or laid close by, Distributed Temperature Sensing (DTS) helps detect changes and faults allowing the operator to intervene before the cable fails. It is suitable for deployment in any cable where an optical fiber is present, including HVDC, HVAC, export, inter-array, transmission and distribution.
-
product
QSFP+ Twinaxial Cable, 5m
785685-05
1-Pin, Male QSFP+ to 1-Pin, Male QSFP+ SFP Cable - The QSFP+ Cable connects to the quad small form-factor pluggable (QSFP) ports on some PXI Ethernet Interface Modules and other hardware devices. The model also has multimode optical fiber options that you can use in tandem with QSFP+ optical transceivers. The cable is rated for transmission speeds up to 40 Gbps and is offered in different lengths.
-
product
Refractive Index Profiler
S14
The S14 Refractive Index Profiler complements optical fiber preform analysis measurements by providing highly accurate and precise characterization of the refractive index profile of drawn single-mode, multimode, and specialty fibers using the RNF (Refracted Near Field) technique. The S14 index profile data produces fiber geometry information directly. Manufacturers can also use S14 data for the prediction of fiber transmission parameters such as mode field diameter, cut-off wavelength, and chromatic dispersion.
-
product
Series Connector
HMA-J
The OPTOKON HMA-J connector series, a medium size „Expanded Beam“ connector is designed for connection of the nodes of harsh environmental network by the help of cables with optical fibers. The used expanded beam technology preservers all advantages of signals transmission through the optical lines in field harsh environmental conditions. Additionally to ruggedized optical networks the HMA-J is suited for a vast array of applications, like heavy industry connections, petrochemical application, broadcasting temporary optical lines. The innovative designs ensure its ability for deployment in the toughest environments where high performance and total reliability are critical. Benefiting from expanded beam technology the precision optical alignment system creates immunity from water, mud, dust oil and other contaminants. The HMA-J Hermaphroditic coupling eliminates the need for adaptors and male and female mating halves. Hermaphroditic housings allow for rapid deployment, creating low loss Singlemode and Multimode daisy chained links in a variety of planforms ranging from simplex fiber to a four fibers. The OPTOKON HMA-J is ideally suited for environmental extremities where low maintenance and quick repairability is necessary.
-
product
Optical Signal Transmission
Analog
Used for oscillographing analog signals under EFT/EDS/RF interference.
-
product
Fiber Cable, Multimode, OM3, 50m
784184-50
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Fiber Adapter
I2C fiber adapter
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*Up to 350kHz*Up to 50m*No software or drivers required
-
product
Active Optical Connectors
Panasonic Industrial Devices Sales Company of America
All-In-One Design, Integrated Fiber Cable for High-Speed Transmission.Panasonic, a worldwide leader in Connector Products, offers the V Series Active Optical Connectors. Featuring a built-in Laser Diode and Photodiode along with an electrical/optical conversion function, the V Series is an all-in-one optical transceiver capable of transmission rates up to 8 Gbps.
-
product
Fixed Laser Source Module
Keysight offers a broad choice of fixed laser sources, which are available as single-wavelength and dual-wavelength modules as part of the Keysight Lightwave Solution Platform. The Keysight 8165xA Fabry-Perot laser sources can be used in conjunction with optical power meter modules for insertion loss, optical return loss and PDL measurement of broadband components and fiber. The Keysight 81663A Distributed Feedback Laser Sources are best suited for amplifier test and WDM system test applications. Keysight covers PON and common WDM wavelengths with its 81663A Distributed Feedback (DFB) laser source modules. The precise tunability around ITU-grid center wavelength gives you the flexibility to match test setups to the latest requirements of the DWDM-system. The fine-tuning allows to shift the center wavelength from one DWDM transmission channel to the adjacent channel in dense WDM systems. The built-in isolator ensures highest laser stability, even when reflections are present in the optical path.
