Filter Results By:
Products
Applications
Manufacturers
OTA
signals transmitted without cables. AKA: Over The Air
See Also: Wireless, Over the Air, Antenna Measurement
-
product
Over-the-Air Radio Waveform Analyzers
Monitors and measures all radios on a network over-the-air (OTA) in real-time without user interventionProactively helps you manage all of your radios in your networkMultiple receivers may be networked to provide system wide coverage
-
product
Universal Compression Tester for Gasoline Engines
34000
Test compression on all domestic and foreign cars and most trucks. Adapters fit vehicles with 14mm and 18mm plugs including long reach and 5/8" hex plugs. Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold. Screw in adapters guarantee accuracy over push-in type testers. Quick side release valve permits retest without removal of adapters. Gage ranges 0-300 PSI and 0-21 BAR. Supplied in storage pouch.
-
product
External Frontend
FE44S
The R&S®FE44S external frontend can extend the frequency range up to 44 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE44S enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. The R&S®FE44S uses a single RF connector to further reduce the number of antennas in over the air testing.
-
product
60kw off grid power inverter 110/220V split-phase output converter
SDP-60KW
Zhejiang Sandi Electric Co., Ltd
Our SDP series Off Grid Pure sine wave inverter is one of the most advanced DC to AC conversion products in the world, it is suitable use for areas without electricity, vehicles, ships, solar energy, wind turbine and other renewable energy systems and etc, can supply power and provide guarantee effectively for the areas with traffic inconveniences, in the mountains, pastoral, border, island and other areas without electricity. It has the main advantages of high quality sine wave AC output, microcomputer control, humanness design, and it is high efficiency and low no-load loss, and no pollution. The inverter can also supply AC power to all kinds of electric equipment, air conditioners, motors, refrigerators, lights, TV, electric fans and other industrial power supply.1. Using the sixth generation efficient IPM intelligent module from Japanese Mitsubishi, high efficiency and stable performance. It with powerful protection function, the protection for short circuit, over load, over temperature is more safe and reliable. It’s service life can up to 15 years or more.2. Intelligentized, modularized, simple structure design with powerful function.3. Two kinds of start mode: Step-down Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converter’s usage, which reduced the cost of equipment investment, easy to connect wires and control.4. The output frequency can be setting via LCD panel, it’s very convenient for customer.5. The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy ±1%.6. The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel.7. Pure sine wave output. With good dynamic response less than 50MS, waveform distortion rate smaller, higher conversion efficiency and stable output voltage.8. Low Frequency Transformer, which ensures that inverter has high efficiency.9. High conversion efficiency, Max. Efficiency≥94%,if 48VDC input,the efficiency can more than 85%.10. Adopts black pure aluminum radiator, which confirms the best radiating performance.11. Powerful data display function. LCD can display the DC input voltage, output frequency, phase voltage, phase current, AC bypass input voltage, output power KWH, time and date, temperature, fault code display.12. Wide input voltage can be set according to customer’s requirement. Input voltage range can be selected from 150-400V or 300-600V or 400-800V.13. Wide input voltage can work without battery and solar charge controller,save more cost and With MPPT wide voltage input function, maximum use of solar power
-
product
Environmental Chamber
REXMED REC-200
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Medium-size Reverberation Chamber
E-Series
The E medium-size multicavity Reverberation Chamber Series represents that state-of-the-art in reverberation chamber technology. The E-Series can make single measurements, batch tests, protocols or campaign tests for different frequency bands, different technologies and different channel models, running overnight without human intervention. Embedded frequency-, mode-, source- and platform-stirring in a double-shielded set of cavities allow Passive MIMO (Efficiency, Correlation, Diversity Gain, MIMO Capacity and others), Active MIMO OTA (TRP, TIS, TPUT, MTS, CQI, M2TxDT, RSRP, MCL and others) and Time-Domain MIMO (DL/UL TCP/UDP TPUT, RMS DS, STD, PL, CBW, Mute%, eNodeB, VDT-OTA) measurements up to 8x8 and 8DLCC to be performed for antennas and devices up to 50cm and 50kg ranging from 2G to 4G, covering all available cellular and wireless technologies to date, including wearables devices, sound acoustic mute, WLAN and W-IoT testing. There is no RC in the market more advanced than the E-Series.
-
product
*High Current Switches
B-1002
Ross High Current Switches are available up to 36,000 amps continuous and over 1,700,000 amps 20µsec RC pulse, with voltage ratings of 6 volts to 400kV peak test. Standard Ross high current switches are built with 80 to 120psi air cylinder actuators. Air cylinder or motor operated for high contact force. Arcing contacts optional for closing current. G-10 epoxy glass laminate is standard insulation on most models. G-7 silicone glass is used on models available for RF applications above 100kHz. Most Ross high current switches are available with additional lengths of insulation, where the high voltage contacts need to be spaced at a greater distance from the actuator and control circuit. Voltage withstand value is at least doubled and the interrupt capability is much greater when high current switches are immersed in insulating oil, fluid or SF6 gas. For gas atmosphere, no modifications are necessary; however, oil or fluid immersion requires modification at a slight extra cost.
-
product
Fabric Pneumatic Bursting Tester
TF142C
TESTEX Testing Equipment Systems Ltd.
Fabric Pneumatic Bursting Tester, to determine the bursting pressure of fabrics uses pneumatic test method, including knits, woven fabric, non-woven fabric, laminated fabric and other craft-made fabric.A test specimen is clamped over an expansive diaphragm by a circular clamping ring, increasing compressed air pressure is applied to the underside of the diaphragm, causing distension of the fabric until the test specimen bursts, the bursting strength and distension are determined.
-
product
Rack-Mountable CATR Chamber for 5G NR mmWave Signals
ATS800R
The R&S®ATS800R CATR based 5G NR mmWave test chamber provides a very compact over the air (OTA) testing environment for testing 5G FR2 antennas, modules and devices in R&D. The R&S®ATS800R has a very small footprint and wide frequency range, and offers maximum functionality and test coverage in a small space. The flexible setup options and range of extensions make the R&S®ATS800R a solid and future-proof environment for your FR2 testing needs.
-
product
Enlarge Environmental Chamber
REXMED REC-450
MOD. REC-450, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,644 Watts, 12,433 BTU/hr, 3,140 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Anemometers
Anemometer accessory head for use with our modular instruments that measures air velocity and temperature in English or Metric units: Ft/min, M/s, MPH, KM/hr, ºF (degrees Fahrenheit) or ºC (degrees Celsius). Multiply your air velocity by the register’s free area to estimate CFM or diagnose duct blockages and quickly check the airflow balance in a conditioned space. Use with our DL3 Data Logger to track airflow or temperature over time. Features average and real time testing modes.
-
product
Broadband Amplifiers
Blonder Tongue Laboratories, Inc.
Blonder Tongue offers a variety of RF amplifiers for broadband CATV or OTA (over-the-air) applications. Be it a 1GHz power doubling two-way indoor distribution amplifier or a mast-mounted preamplifier, or anything in between, we have you covered.
-
product
Rack based antenna test system
R&S®ATS800R CATR
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique rack based CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
product
Antenna Test Systems and OTA Chambers
With our well-established experience in innovative solutions based on top-quality engineering, Rohde & Schwarz provides you with leading antenna test systems and OTA chambers.
-
product
Radar Altimeter Test Set
Core Technology
Eastern OptX core technology enables the conversion of microwave signals to optical signals (E/O), time delaying this signal then reconverting the light back to original microwave signal (O/E) with superior fidelity over traditional time delay methods. Products include Radar Target Simulation, Radar Altimeter Testing, Channel Simulation (Air Interface) and Multipath Creation.
-
product
Small-size Reverberation Chamber
PT-Series -
The PT small-size Reverberation Chamber Series is a one-of-its-own OTA set of test chambers worldwide. With smart-stirring and capable of simultaneously testing up to 8 DUTs of up to 15cm and 5kg, the PT-Series is intended for Production OTA Testing in non-signaling mode, providing unheard-of ultra-fast test times with good accuracy and repeatability and the second smallest footprint on the market, only superseded by our I-Series. TxPower, RSSI and other non-signaling SISO and MIMO test figures of merit for all cellular and wireless technologies, including Main/Diversity/All antenna switching, can be performed in a wide variety of Operating Systems (Windows, Android, iOS, mac OS, Linux, UWP and Tizen).
-
product
Car-to-X Signal Strength Emulator
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
product
Antenna Couplers
Concentric Technology Solutions, Inc.
RF Antenna Couplers help create the ideal environment for shield boxes by providing a consist, stable and reliable environment for repetitive over the air (OTA) tests.
-
product
Super MUTT Deluxe Standard Edition
#9008-SE
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
CATR Benchtop Antenna Test System
ATS800B
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
product
Enlarge Environmental Chamber
REXMED REC-250
MOD. REC-250, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Propsim Channel Emulation Solutions
Propsim Channel Emulation Solutions are versatile and easy-to-use in a wide range of applications including MIMO, Beamforming, WLAN, Aerospace, MANET and MIMO OTA testing.
-
product
Super MUTT Deluxe Edition Electrical Circuit Tester
#9008-DL
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
Large-size Hybrid Reverberation / Anechoic Chamber
F-Series
The F large-size hybrid Reverberation/Anechoic Chamber represents the most versatile OTA test system in the market today. With the same unique test features of their E Series RC counterparts, the F-Series can also test large form-factor devices under test (DUTs) like laptops, large TV sets, solar and trash compactors, drones, fridges or washing and vending machines, among others. With up to 16x16, 8DLCC and DUTs up to 2m and 500 kg including full-body phantoms in a turntable, the F Series also expands the frequency range down to cover 200 MHz up to 40 GHz frequency ranges and the test modes to include EMC, BS, small cell, eNodeB and Virtual Drive Testing over the air (VDT-OTA). In an again unheard-of feature, the F-Series is also reverse-convertible into an Anechoic chamber, allowing Far Field (FF) and Spherical Near Field (SNF) radiation patterns, efficiency and gain measurements and pre-5G testing of antennas and devices. Conversion from RC to AC or vice versa can be performed within half a day.
-
product
5G Active Antenna Innovator’s Kit
AWMF-0129
The AWMF-0129 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +50dBmi output power while consuming just 12W DC power in the RF circuits and has achieved Gb/s data rates in OTA trials. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWMF-0129 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
product
OTA Chamber for 5G NR mmWave Signals
ATS1800C
The R&S®ATS1800C CATR based 5G NR mmWave test chamber provides the ideal environment for testing 5G FR2 antennas, modules and devices over the air (OTA) from R&D to conformance. With its small footprint and wide frequency range, the R&S®ATS1800C offers great functionality and test coverage in a very small space. With its flexibility and broad range of extension options, the R&S®ATS1800C offers a solid and future-proof environment for your FR2 testing needs.
-
product
Heavy Duty Compression Tester for Gasoline Engines
34300
Use to test compression of gasoline engines on domestic and foreign cars and trucks plus motorcycles, snow mobiles and lawn mowers.Adapters provided for 10mm, 12mm, 14mm and 18mm applications.Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold.Screw-in adapters provide better accuracy over push-in type testers.Quick disconnect for easy hook-ups.Quick side release valve permits retests without removal of adapters.
-
product
External Frontend
FE50DTR
The R&S®FE50DTR external frontend can extend the frequency range up to 50 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE50DTR enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. With a dual connector system, testing of active components is an easy task.
-
product
Wireless Devices
Schweitzer Engineering Laboratories, Inc.
Wireless devices use radio signals to communicate and pass data over the air, eliminating the need for traditional cabling.
