Filter Results By:
Products
Applications
Manufacturers
Measurement Microphones
measure acoustic frequency, time and noise levels.
See Also: Microphones, Hydrophones, Mic
- CAMI Research Inc. (CableEye®)
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
CAMI Research Inc. (CableEye®)
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
product
Type 1 Phantom Powered Measurement Microphone
MK224PH
The MK224PH Type 1 phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Frequency Response: +/-2dB (8 Hz to 18kHz). Sensitivity: 50 mV/Pa (-26 dBV/Pa)typ. Dynamic Range 3% THD: 14dBA-145dB.
-
product
Sound Level Meter
831-LOWN
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
-
product
Electroacoustic Test
CRYSOUND offers comprehensive and expert electroacoustic measurement solutions for a broad spectrum of consumer electronics, including headphones, microphones, and speakers. These solutions are characterized by powerful functionality and robust stability.
-
product
Handheld Audio Analyzer
PAA3X
The PAA3X is a highly accurate handheld audio analyzer that gives sound engineers a rich array of sound analysis tools. The system features both 61-band and 31-band real time spectrum analysis, RT60 reverb time measurement, SPL and line meter, internal signal generator, EQ setting program, microphone calibration and speaker phase checking abilities. All functions and menus can be accessed through a central jog dial, leaving your other hand free to adjust audio settings. The large color LCD screen has an adjustable brightness to help you see in a dark or well-lit environments alike. The PAA3X also features a "screen capture" function allowing users to save images of the screen to an SD card in BMP format for later reference. The detachable precision microphone can be placed remotely via the included 5-meter extension cable, offering flexible on-site operation management. With all this plus a built-in rechargeable lithium-ion battery, the PAA3X is a must-have multifunctional tool for all serious audio engineers.
-
product
Mobile Cable Fault Location System
BAUR Syscompact 4000
BAUR Prüf- und Messtechnik GmbH
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
-
product
Audio Analyser
ATB PC Pro
The ATB PC Pro Measuring system is a professional Audio Analyser. The Windows program is combined with the computer’s soundcard, the measurement microphone, the Test-Box and the DVD (CD) for the signals forms an exact and extensive measurement system. The applications for the ATB PC Pro are the speaker development, room acoustic optimise, the installation of car sound systems, the setting of Surround reproduction systems and the noise analyser.
-
product
Microphone Measurement Capsule
TG MM1W
Interchangeable measurement microphone capsule for TG 1000 handheld transmittersTo calibrate ELA and PA systems in the theatre, at live concerts or at festivals
-
product
Acoustical Generator (STIPA Reference)
TalkBox
The TalkBox is an acoustic signal generator for speech intelligibility measurements in evacuation and announcement systems, as well as for level alignment of teleconference or other audio systems. It allows you to perform a complete end-to-end evaluation of the speech intelligibility STI from the talker’s microphone to the listener’s ears.
-
product
Precision Sound Level Calibrator
CAL200
The Larson Davis CAL200 Sound Level Calibrator is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment.
-
product
XOn Accoustics System
XOn Accoustics System
The "XOn Accoustics System" unites the flexibility and efficiency of an industry PC with the sensitivity and capabilities of a high resolution microphone. The system provides a wide selection of measurement methods. In the standard model, the following routines are already included: 3rd Octave Analysis, 1/n Octave Analysis, FFT analysis, FFT power spectrum density, FFT power spectrum analysis.
-
product
Sound And Vibration Measurement
With over 20 years of professional experience, rigorous testing, and quality control, BSWA measurement microphones lead the market with excellent performance.
-
product
50KHZ MEASUREMENT MICROPHONE
M50
The M50 is a precision engineered 50kHz omnidirectional measurement microphone ideally suited for acoustical measurements including high-end loudspeaker design and quality control, scientific research, measurements of ultrasonic or subsonic transducers, or any application where an extremely accurate free-field measurement microphone is required.
-
product
ultimate measurement microphone
cm-145
The CM-145 is a very low noise, flat frequency response, omni-directional microphone built to IEC651 Type 1 standards and comparable to the B & K 4006. This is an electret condenser microphone with a 1/2 diaphram of nickel-copper alloy. Included with the microphone is a shock mount, foam lined wood storage box and individual calibration chart.
-
product
Class 2 Sound Pressure Level Meter
Castle Sonus GA216B
This class 2 Sound Level Meter (GA216B) is a feature packed instrument that is fully complient with IEC 61672-1:2002. This meter provides you with the ability to measure sound pressure (Lp) and peak (Cpeak) simultaneously, a requirement for multiple tasks including initial spot-check assessments to the Control of Noise at Work Regulations 2005. The body is designed from tough, crack resistant ABS plastic, ensuring your new Sound Level Meter will survive the conditions for which it was intended. Coming with a high specification measurement microphone which has been calibrated before you receive it, you can be sure your readings are accurate from day one.
-
product
23KHZ Measurement Microphone
M23
The M23 is a precision engineered 23kHz omnidirectional measurement microphone ideally suited for acoustical measurements including loudspeaker design and quality control, sound system setup and troubleshooting, room acoustics, or any application where an accurate free-field measurement microphone is required.
-
product
GSM RF Interference Test System
Guangzhou Jumho Electric Co., Ltd.
Cell phones and other wireless devices radiate powerful electromagnetic fields that can cause interference and noise in microphone signals. The interference and noise is called RF interference, which is an unwanted “signal” that occurs at the same time and frequency as a data signal. The RF interference disrupts the flow of data and degrades quality-of-service. Jumho Electric provides a cost-effective RF interference test system for GSM interference level measurement of wireless microphone.
-
product
USB-4431, 102.4 kS/s, 100 dB, 0.8 Hz AC/DC Coupled, 4-Input/1-Output Sound and Vibration Device
780164-01
The USB-4431 is designed for sound and vibration measurements. Input channels incorporate integrated electronic piezoelectric (IEPE) signal conditioning for accelerometers and microphones. The four USB-4431 input channels simultaneously digitize input signals. The analog output (AO) channel is ideal for stimulus-response tests and can be synchronized to the AI channels.
-
product
Outdoor Microphones
Is a measurement microphone for all-weather conditions designed for use with sound level meters.
-
product
Measurement Microphones
All microphones are omni-directional and 48V phantom powered. The XL2 Analyzer microphones include an electronic data sheet. The Automated Sensor Detection (ASD) of the XL2 automatically reads this data sheet, and recognizes the microphone model, sensitivity and calibration data. This ensures accurate measurement results.
-
product
Sound & Vibration
Ono Sokki Sound & Vibration measurement products - sound level meter, microphone & amp, accelerometer, vibration, laser doppler vibrometer, and related software.
-
product
Sound Level Indicators
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, a sound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site.An important attribute to consider when searching for a suitable sound level meter is its type or class. The type or class of a sound level meter defines the device's accuracy as per American National Standards Institute (ANSI) or International Electrotechnical Commission (IEC) guidelines. Typically, "type" is the grade according to the ANSI S1.4 standard, whereas "class" is the grade according to the IEC 61672 standard. There are two types or classes assigned to sound level meters: type 1 / class 1 or type 2 / class 2. For assessing noise in basic industrial, commercial, educational, recreational or residential applications, a type 2 / class 2 sound level meter usually will suffice. For precision-grade assessments often made in a laboratory, a type 1 / class 1 sound level meter primarily is used. PCE sound level meter products are lightweight, easy-to-use and manufactured in accordance with the highest industrial standards.
-
product
USB-4432, 102.4 kS/s, 100 dB, 0.8 Hz AC/DC Coupled, 5-Input Sound and Vibration Device
780421-01
The USB-4432 is designed for sound and vibration measurements. Four of the input channels incorporate integrated electronic piezoelectric (IEPE) signal conditioning for accelerometers and microphones and built-in antialiasing filters that automatically adjust to your sampling rate. The fifth input channel does not include IEPE support.
-
product
Real Time Audion Spectrum Analyzer
TrueRTA's audio spectrum analyzer software shows you a detailed picture of what you're hearing in real-time, that is, as it happens. You can create your own professional measurement system starting with TrueRTA software on your PC. Then add the measurement microphone, preamp and USB interface of your choice. TrueRTA accurately tests audio systems using a Windows PC with basic sound capability. TrueRTA turns your PC into a powerful audio test system normally seen only in better audio research and design laboratories. TrueRTA runs under Windows Vista, 7, 8 and 10.
-
product
PXIe-4497, 204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module
781369-01
204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module - The PXIe‑4497 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4497 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4497 delivers simultaneous sample on all channels. In addition, the module includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gain, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
product
1/4-inch Measurement Microphone and Preamplifier
MI-1531/MI-3140
The 1/4-inch diameter condenser microphone MI-1531 with its preamplifier MI-3140 enable to measure the high frequency band more than 20kHz which it is impossible by using the 1/2-inch microphone. Amplifier is not required in use as it is a back electret-type condenser microphone, which differs from a bias-type microphone. And also, the MI-1531 achieves a measurement at Max. 168 dB as a performance of a microphone itself.
-
product
Special microphones
G.R.A.S. Sound & Vibration A/S
Special microphones are often required for applications where there are particular requirements regarding the methods of measurements and configurations
-
product
2-Channel Front End
BEQ II.1
*Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.
-
product
23KHZ Reference Measurement Microphone
M23R
The M23R is a precision engineered 23kHz omnidirectional measurement microphone ideally suited for acoustical measurements including loudspeaker design and quality control, sound system setup and troubleshooting, room acoustics, or any application where an accurate free-field measurement microphone is required.
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
instrumentation microphone
josephson c550h
A precision omnidirectional measurement microphone by Josephson Engineering that is thermally conditioned for stability and manufactured in California. These mics are individually calibrated and matched for sensitivity at the Josephson facility. The nose diameter fits nominal ½” calibrators perfectly. This is an excellent product and a great value for an instrumentation microphone and is supplied with a mounting clip and vinyl pouch.
