Filter Results By:
Products
Applications
Manufacturers
Jitter
Unwanted signal deviation.
- Pickering Interfaces Inc.
product
LXI WTB Terminator, 109.8 ohm
60-983-003
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Infiniium V-Series Oscilloscope: 25 GHz, 4 Analog Channels
DSAV254A
25 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
28/45 GHz Single Optical Channel DCA-M with Option CDR
N1092A
High accuracy, low cost solution for optical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, fast sampling rates for high throughput, and integrated clock recovery available.
-
product
Infiniium V-Series Oscilloscope: 33 GHz, 4 Analog Channels
DSAV334A
33 GHz analog bandwidth4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Signal Generator, 20MHz, 2 Channel, Arb.
33512B
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
product
GL Products Online & Interactive Demos
*NetSurveyorWeb™ is a centralized VoIP network monitoring system. A number of GL's PacketScan™ probes and/or,PacketProbes™ are deployed in remote locations across the network to passively monitor VoIP traffic. Whenever a monitored call completes, the scan/probe calculates a variety of quality metrics (MOS, loss, delay, jitter, etc) and sends the metrics to the central Oracle database for storage.**The PacketScan™ is a feature-robust Windows® based software tool that captures and monitors live IP traffic. In the VoIP world, it can monitor and measure SIP, H323, Megaco, MGCP, T.38 and video calls. In addition to quality metricsPacketScan™ also captures signaling information and sends that to the NetSurveyorWeb™ database as well.**GL's PacketProbe™ is an advanced CPE(Customer Premises Equipment) based VoIP monitoring reporting and diagnostic appliance, stemming from GL's suite of market leading voice analysis tools.
-
product
NRZ Analysis for Signal Integrity Studio, WavePulser 40iX High-Speed Interconnect Analyzer
WAVEPULSER-SI-STUDIO-NRZ
Signal Integrity (SI) Studio uses SDA Expert (SDAX) serial data analysis software options to simplify NRZ or PAM serial data jitter, eye diagram, noise and crosstalk measurement and analysis setup.
-
product
Broadband Digital Signal Delay Lines
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-32Gbps / DC-17GHz) tunable clock/data phase shifterDelay adjustment range of 265psExhibits low jitter and limited temperature variation over industrial temperature range1GHz of bandwidth for the phase adjustment tuning portFully differential CML input interfaceFully differential CML output interface with 600mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 1WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
product
Limiting Amplifiers
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-28Gbps) limiting amplifierExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the amplitude adjustment tuning portIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with adjustable SE amplitude from 0V to 1.0VSingle +3.3V or -3.3V power supplyPower consumption: 660mWFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
product
Multi-Instrument BERT Software
N4980A
The Keysight N4980A multi-instrument BERT software provides the ability to control multiple instruments through a rich Windows-based graphical user interface (GUI). Bit error rate measurements are simple to set up with the intuitive control screens. The software is ideal for setting up and performing parallel BER measurements and jitter tolerance testing (N4980A-JTS) in multi-lane and SERDES devices. You can also create your own patterns using the powerful editing tools built into the pattern editor to meet your unique requirements.
-
product
Clock Generation Devices
Analog Devices offers ultralow jitter clock generation products for wireless infrastructure, instrumentation, broadband, automatic test equipment, and other applications demanding subpicosecond performance. Our clock products are ideal for generating the high speed, low noise clock signals required to clock high performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). ADI clock ICs integrate PLL cores, dividers, phase offset, skew adjust, and clock drivers in small chip scale packages.
-
product
HDcctv Relockers
Macom Technology Solutions Holdings Inc.
MACOM’s reclockers are specifically designed to help customers build robust solutions by removing jitter from video signals. These multi-rate products are essential when designing security and surveillance equipment.
-
product
WaveMaster Oscilloscope, 4 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 804Zi-B
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
product
PCIe Gen3 X16 Bus Expansion Via Dual X8 OCuLink (as A Single Combined X16) Via Rear I/O
PCI124
The PCI124 is one of VadaTech’s 4th generation PCIe expansion module based on the PCI-SIG specification. The Module has a Retimer/Conditioner to improve signal integrity for enhancing system performance and reliability across long cables. It removes both random and deterministic jitter from the input signals eliminating inter-symbol interference and resets the output jitter budget. It supports the full 16 lanes.
-
product
Test SIP
VoIP, Video, and IPTV products must withstand and continue to function when facing all the conditions that occur on the Internet. These include attacks from hackers exploiting vulnerabilities in security and protocols as well as the common phenomenon of congestion, delay, jitter, drops, and so on. VoIP, Video, and IPTV products must demonstrate robustness and resiliency in the face of unusual and/or illegal conditions.
-
product
Accessory for Test Chest 3G Facilitating 'EYE' Analysis
EYE~POD
Designed to interface with Murraypro's Test Chest 3G, the EYE~POD accessory module extends monitoring capability to include SDI envelope parameters from SD through to 3G. Users receive immediate visual indication of the quality of an SDI input signal with regard to both overall signal amplitude and Jitter. Drawing power from TC3G, the coupled-combo may be used on local battery power, or supported with an external mains PSU
-
product
Real-time IP network measurements
IPProbe
Real-time network measurements for multiple IP interfaces. Detection of Packet loss, IAT (Inter Arrival Time), Delay, Bitrate and ETR290 problems. Stable packet generation and receiving is a key feature required in any modern IPTV environment. Any irregularity and/or discontinuity in this packet stream means buffering problems or losing frames. IP jitter provides a means to see the distribution and stability in the IP stream.
-
product
High-Speed Digital Testing
Silicon Turnkey Solution, Inc.
High-speed devices create significant challenges for functional testing, for example, the need for high-bandwidth interfacing to maintain signal integrity at multi-gigabits per second data rates and the ability to measure high-speed bit error rate and jitter. STS brings extensive experience in high-speed functional testing for commercial, military and aerospace devices to meet the most stringent customer requirements. Our highly integrated testing laboratory and efficient workflow are designed with one goal in mind: to shorten time-to-market and enhance our customers’ ability to compete.
-
product
Infiniium V-Series Oscilloscope: 16 GHz, 4 Analog Channels
DSOV164A
16 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Jitter Noise Generator
J7000
The J7000A Series instruments high crest factor output is used as a random jitter source for serial data bus applications, including PCI Express Gen I & II, Serial ATA, and Fiber Channel. The noise source is designed for the PCI-SIG total jitter (Tj) model serial data application, but can be used for any random jitter noise application.
-
product
Single-Lane PCIe Equalizer/Redriver
MAX14950A
The MAX14950A dual equalizer/redriver improves PCI Express® (PCIe) signal integrity by providing programmable input equalization. This feature reduces deterministic jitter and redrives circuitry to reestablish deemphasis, which compensates for circuit-board loss at high frequencies. The device permits optimal placement of key PCIe components and allows for longer runs of stripline, microstrip, or cable.
-
product
Function/Arbitrary Waveform Generators
SDG800 Series
The SDG800 series function/arbitrary waveform generator family outputs waveform functions up to up to 5 MHz (pulse), 10 MHz (square), 30 MHz (sine) and has a sampling rate of 125 MSa/s. They are powered with SIGLENT’s EasyPulse technology which produces low jitter, fast rising/falling edges without being affected by frequency, even at low duty cycle settings, allowing the user a wide range of pulse widths and transition times. This results in a much more versatile generator than other similar DDS designs.
-
product
Mixed Signal Oscilloscope: 33 GHz, 4 Analog Plus 16 Digital Channels
MSOV334A
33 GHz analog bandwidth4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Super Phosphor Oscilloscopes
SDS1000X-E Series
SIGLENT’s new SDS1000X-E Series Super Phosphor Oscilloscope is available in 100 and 200 MHz bandwidths and 2 or 4 analog channels. It has a maximum sample rate of 1 GSa/s and a standard record length of 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.The SDS1000X-E series employs a new generation of SPO (Super Phosphor Oscilloscope) technology that provides excellent signal fidelity and performance. The system noise is also lower than similar products in the industry. It comes with a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/ sec (sequence mode).
-
product
Transimpedance Amplifiers
Advanced Science and Novel Technology, Co., Inc.
Broadband transimpedance amplifier for low noise receiver side applicationsFeatures automatic input offset control and a peak detector8GHz of analog bandwidth for limiting of input data60dB of transimpedance differential gain15pA/sqrtHz of input referred noise density (0.1 to 10GHz)CML output interface with 50 termination and 225mVp-p single-ended swingSingle +3.3V power supplyPower consumption: 250mWExhibits low jitter and limited temperature variation over industrial temperature rangeUnpackaged bare die
-
product
28/45 GHz Quad Optical Channel DCA-M
N1092D
High accuracy, low cost solution for optical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, and fast sampling rates for high throughput.
-
product
Dual Channel Arbitrary Function Generator
TGF4000
High resolution, low jitter pulses can be generated up to 100MHz as can wide bandwidth white noise. A extensive array of modulations is provided using internal and external sources. Gated, burst and sweep modes can use internal or external trigger sources. Remote control via USB and LXI compliant LAN (standard) can be supplemented by optional GPIB if required.
-
product
Pulse Pattern Generator, 3.35 GHz, dual-channel
81134A
When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. On top of that, it allows to generate application-specific signal levels like pre- and de-emphasis (PCI Express) or squelch (Serial ATA). The Keysight 81134A lets you test your DUT instead of the pulse or data source!
-
product
Digital Storage Oscilloscope
SDS6000A
The SDS6000A series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 170,000 wfm/ s (normal mode, up to 750,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. Tools such as History waveform recording, Search and Navigate functions, Mask Test, Bode Plot, Power Analysis, and Eye/Jitter Analysis allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 25 MHz arbitrary waveform generator, as well as serial decoding are also features of the SDS6000A Digital Oscilloscope.
-
product
Quality Of Service
Traffic is prioritized according to its importance and some types of traffic are more sensitive to latency, jitter and packet loss than other. Xena offers QoS validation solutions in accordance with RFC 2544 and Y.1564, as well as advanced statistics functions that help users track, analyze and troubleshoot QoS to maintain a high service quality guarantee. Testing that link performance complies with a Service Level Agreement (SLA) includes verifying Frame Transfer Delay (FTD), Frame Delay Variation (FDV) and Frame Loss Ratio (FLR) at the Committed Information Rate (CIR) defined in the SLA. Verifying the SLA with the Xena1564 allows doing the test on a line simultaneously loaded with traffic from other services.
-
product
SDI Reclockers
Macom Technology Solutions Holdings Inc.
MACOM’s reclockers are specifically designed to help build robust video broadcast systems by removing jitter from Serial Digital Interface (SDI) video signals. These multi-rate products are essential when designing high definition (HD) and ultra high-definition (UHD) systems that are compliant with the Society of Motion Picture and Television Engineers (SMPTE) standards.
