Filter Results By:
Products
Applications
Manufacturers
- PJ Electronics, Inc.
product
Multi-Operational Surge Tester
MB Model
Bench all-in-one versatile Multi-Operational Surge Tester that you need for all of your electrical insulation testing. The Hi-Pot tester has separate L.E.D. panel meters for direct readout (voltage and leakage current) so that no interpolation on the scopes display is ever needed. This MOST can surge test extremely low inductance windings, DC armatures, etc.
-
product
Inductance Standard
1482 Series
The GenRad 1482 Standard Inductors are the standard of choice in metrology labs. Used today by national metrology institutes and primary standards bodies around the world, these inductors have no peer or equivlent.
-
product
LCR Meters
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
product
Single-Stage Current Sensors
The robust low-noise single stage current sensors are available with input inductances from 24 nH to 1.8 µH and a flux noise of 1.2 µPhi0/sqrt(Hz).
-
product
Filter Test System
DU7216/7218
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
product
Smart Card Module Test Cells
Current and voltage measures are executed on defined pins, in stable conditions.Measurements:- Open/short- Input leakage current- IDD Supply instant/average current test (static/dynamic mode)- Input capacitance @13 MHz and inductance- Retro modulation index (RMI)Test of passive devices:- Capacitors- Resistors- Resonators
-
product
DC BIAS CURRENT UNIT
3265B SERIES
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
product
HV AC Voltage Test Systems
Fivestar HV Testing Equipment Co., Ltd.
FSHV offers three different types of AC voltage test systems, the conventional type is AC test transformer design, mainly for testing objects of medium & low capacitance products, particularly for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (like inductive voltage transformers). Another is AC resonant test systems, according to series resonance circuit XL=XC (2πfL=1/2πfC), by setting F frequency of power supply or L inductance of reactor, generate a pure sinusoidal waveform of the test voltage, and the required input power is only 1/Q. Variable frequency type operates in a frequency range from 20Hz to 300Hz, ideal for field commissioning test of power cables and GIS/GIL. Variable inductance type outputs continuous AC voltage of power frequency (50/60Hz), mainly for factory testing of high and ultra-high voltage cables, power transformers, GIS, etc.
-
product
20000 Counts LCR Meter
LCR612 / LCR612R
Dual Displays provide quick tested results readouts,with L.C.R. Display values up to 19999 counts and Q.D.R. display values up to 9999 counts (Auto range). Basic accuracy: 0.5% for Resistance ;0.7% for Inductance, Capacitance
-
product
Capacitance Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Inductance capacitance meter is a kind of stable performance, safe and reliable, high precision of handheld 3 1/2 a manual switch range digital instrument. Can be used to measure the capacitance, resistance, triode magnification beta and other functions
-
product
High Frequency LCR Meters up to 30MHz
11050
Chroma Systems Solutions, Inc.
The Chroma 11050 Series HF LCR Meter is a precision test instrument designed to accurately measure and evaluate passive components at high speeds. Its measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components. The HF LCR Meter has a broad testing frequency range 75kHz~30MHz/1kHz~10 MHz/60Hz~5MHz suitable for analyzing component characteristics under different frequencies. Its 0.1% basic measurement accuracy provides stable and highly reliable results. A fast 7ms measurement speed effectively increases productivity when working in an automated environment.
-
product
Electrical Property Measurement
Materials Analysis Technology Inc.
This technology is used to identify the electrical characteristics, such as resistance, capacitance and inductance, of semiconductor devices. Characteristics measured from fail and normal chips could provide important clues for further failure analysis.
-
product
E-field Generators for EMC Testing
AR RF/Microwave Instrumentation
AR E-field generators offer exceptional uniformity between the elements. Our ATE10K30M uses low inductance high-power internal load resistors to terminate RF power, and offers well-matched input VSWR. The ATE10K100M is our own patent-pending folded-dipole type design. And we haven’t yet found a test object the ATE10K25M–1 can’t handle.
-
product
Battery Testers
designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more.
-
product
DC Current Bias Supply
DC1000A
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
product
Low Inductance BNC Cable, VOLT:DC 60V
PX0105A
The Keysight PX0105A is suitable for narrow current pulse measurement down to 10 μs pulse width. It supports the Keysight M9602/03A.
-
product
Autocompute LCR-Q Meter
Model 4910
Aplab Model 4910 is a microprocessor based digital Autocompute LCR-Q Meter that meets today’s laboratory requirements, in the production line and the quality assurance area. It features fully autoranging and automatic operation over a wide range of measurements. Model 4910 measures inductance, capacitance, resistance and quality factor to a basic accuracy of ±0.25% of the reading for values upto 2000H, 2000μF, 2M ohm and Q factor upto 99 respectively. Measurements can be made at a frequency of 100Hz or 1KHz as required and either the series equivalent or parallel equivalent component values can be displayed.
-
product
Parasitics Extractor Tools
FastHenry
Massachusetts Institute of Technology
FastCap and FastHenry, from MIT (Massachusetts Institute of Technology) are two free parasitics extractor tools for capacitance, and inductance and resistance. Quoted in many scientific articles, are considered golden references in their field. .
-
product
Metal Alloy Low Resistance Chip Resistor
MR
*Low Resistance / TCR / Inductance*Excellent long term stability*RoHS compliant and halogen free*Lead free*High precision current sensing and voltage division
-
product
300 V Battery Analyzer
BA6011
The BA6010 Series battery analyzers measure voltage and resistance of modern battery technologies with high accuracy, resolution, and speed. Additionally, these instruments provide auxiliary measurement parameters inductance, capacitance, dissipation factor, impedance, quality factor, reactance, and phase angle in degrees and radians.
-
product
Automatic Capacitance Inductance Tester
HTRG-H / 397
Wuhan Huatian Electric Power Automation Co., Ltd.
Measure each phase capacitance, total capacitance and inductance of compensation capacitor.
-
product
DC Electronic Load
Model - KM-mPD-501
Kusam Electrical Industries Limited
KM-mPD-501 DC electronic load mainly focuses on the testing of power circuit on PCB. KM-mPD-501 offers a solution for function test of Switch step up, Stepdown, Regulators and Driver IC . Engineer puts components, such as CPU, DSP, FPGA; etc on a PCB after the power circuit has been tested. It’s not complete to use a meter to measure the voltage. KM-mPD-501 offers engineer OVP, OCP and OPP functions that help engineer know the value of overload current . On the other hand, engineer can use a programmable DC power supply (mPP series) to offer external power and connect PCB’s output to KM-mPD-501. Then engineer can easily get output watt, figure out the efficiency of power circuit and check if inductances, capacitances and resistances perfectly work with the power circuit. KM-mPD-501 not only offers loading emulation of current but also provides OVP and OPP. User can use these functions to test solar power battery, rechargeable battery and motor driver. In school laboratory, KM-mPD-501 helps students do experiment on power circuit, linear circuit and driver circuit.
-
product
Repeated Charge Discharge Test Set
The IS 13341 : 1992 has laid down the requirements for Ageing Test, Self-Healing Test and Destruction Test on Shunt Capacitors of the self healing type for AC Power Systems. The Ageing Test is to be performed at a specified voltage of 1.25 times the rated voltage for 750 hours. The test is to be followed with a repeated discharge cycle test which involves charging of the capacitor to a DC voltage and discharge of the same through an Inductance. Sivananda Electronics has developed this equipment for the benefit of capacitor manufacturers, for the first time in India.
-
product
Capacitance Tester
LCR55A
The ultimate electronic component verifier measures inductance, capacitance, resistance, transistors, diodes and microwave diodes.
-
product
ESD Testers
Hanwa Electronic Ind. Co.,Ltd.
◆Adaptable to the following international standard waveform;JEDEC, ESDA, AEC, and JEITA◆This system’s uniquely short discharge circuit is made possible by its original mechanical design.◆The short circuit minimizes the influence of inductance and capacitance on the data.◆The use of a single circuit ensures data stability for each device pin tested.
-
product
Source Measure Units and LCR Meters
Source Measure Units are high-precision, high-accuracy DC instruments that can both source and simultaneously measure voltage and current. Additionally, LCR Meters can measure the inductance, capacitance, and resistance (LCR) of electronic equipment.
-
product
Digibridge
1659
The GenRad 1659 Digibridge RLC Tester is an easily programmable, microprocessor-based high performance passive component tester. It automatically identifies the type of component under test and measures in the proper range. The result is simple, precise, unambiguous RLC component testing. The GenRad 1659 RLC Digibridge is an instrument for measuring primary parameters of inductance (L), capacitance (C) and resistance (R) and secondary parameters of dissipation factor (D) and quality factor (Q). GenRad designed this single compact unit with maximum flexibility and operator convenience in mind. The simple front panel design of the Digibridge requires less effort to operate. Digital display and user friendly control allows test parameters and limits to be set easily.
-
product
Precision Current Sensing Resistors
PCR4T
Precision cement resistors designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow high precision measurements even with low resistance values. PCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a ceramic molding. This resistor has low inductance and has high pulse power.
-
product
Electronic Power Testers
Axi'An Beicheng Electronics Co., LTD.
Electronic Power Testers by RuoShui; HART process calibrators, process calibrators, digital earth resistance tester, insulation resistance tester, SMD resistor, digital capacitance inductance meter, LCR meters, surface resistance meter, and more
-
product
LCR Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Inductance capacitance meter is a kind of stable performance, safe and reliable, high precision of handheld 3 1/2 a manual switch range digital instrument. Can be used to measure the capacitance, resistance, triode magnification beta and other functions.
-
product
Electric Motor Checker
CIE/1001
Cambridge Instruments & Engineering Co.
Housed in attractive wooden body with sunmica finish. For comprehensive check of Rotor and Stator Inductance, Resistance and Insulation Resistance without dismantling the Motor. Only to isolate the power supply.
