Filter Results By:
Products
Applications
Manufacturers
Impedance Meters
measure the rate of voltage to current in a circuit at a specified frequency.
See Also: LCR Meters
- Applied Instruments, Inc.
product
Signal Level Meter
XR-3W+
From satellite dish alignment, to UHF off-air antenna pointing, to cable TV MER measurements, the XR-3 is the meter for you! The XR-3 is the most capable meter offered by Applied Instruments. It's more durable than the popular Super Buddy meter, and has added features and performance. The XR-3's modular design with field swappable modules provides wide versatility to fit different measurement applications, including DBS satellite (i.e. Dish Network, DIRECTV, Bell TV, Shaw Direct), VSAT satellite (i.e. iDirect, Hughes Ku band, and more), VHF/UHF off-air (analog and ATSC digital), and CATV (QAM and analog). The XR-3 is great for installing and troubleshooting DISH SmartBox, Blonder Tongue, and other SMATV headend systems often used in hotels, multi-dwelling units, and institutional facilities. Modular Test Instrument. Satellite Finder. Installer Signal Meters. CATV Analyzer. Modules.
-
product
Electric Fence Chargers
Mark 8
Parker McCrory Manufacturing Co.
The all new Mark 8, low impedance fencer gives you the stock holding power that you have always wanted. Shocks right through wet weeds or brush and over extremely dry ground. Features Parmak`s exclusive built-in DIGITAL performance meter that tells you the exact condition of the fence. Takes the guesswork out of electric fencing. 100% solid state, with all new low impedance, uni-junction circuitry. No moving parts. Ideal for use with high tensile single or multi-wire fences. New color coded fence and ground terminals. Red to the fence and Black to ground. The Mark 8 operates for less than 7 cents a month at 7 cents per kwh. Fuse protection, with new built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
product
Impedance Meter
ZM-100
Monacor International GmbH & Co. KG
Impedance meter for measuring the impedance (Z) of individual loudspeakers and loudspeaker lines.
-
product
Attenuators And Pulse Limiters
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
product
High Precision LCR Meter
MCR-5000 series
MCR5000 series is a multifunctional LCR precision meter used for testing various electronic components. Adopt 4.3-inch TFT LCD display, simple display, elegant layout. It is a high speed, wide band, 5 bit test resolution impedance measuring instrument with 40hz-200khz multipie frequency points and 0.1% accuracy, which can meet the requirements of component parameter detection in various occasions. Is a high - quality cost-effective tester.
-
product
LCR Meter
ET/QuadTech 1910/1920
The 1920 1 MHz LCR Meter is the most popular and designed to perform capacitance and impedance measurements on a variety of electronic components and materials over a frequency range from 20 Hz to 1 MHz. The1920 features programmable bias voltage from 1 mV to 2 V for biasing capacitors and other semiconductor devices during measurements.
-
product
LCR Meters And Impedance Measurement Products
Complete impedance measurement solutions to meet your needs from LCR to impedance meters, plus test accessories for various R&D and manufacturing applications.
-
product
42.0Hz~5.00MHz, Programmable Impedance / LCR Meter
3550
The Model 3550 Programmable Impedance/LCR Meter tests within the extensive frequency range of 42.0 Hz to 5.00 MHz. It measures L, C, R, |Z|, Y, D, Q, R, Phase, G, X, B, V, I, F, in series or parallel modes. With a basic accuracy of 0.10%, the 3550 is designed for a wide variety of automated or manual test applications. RS-232C & I/O interfaces are standard; GPIB or BCD interfaces are optional.
-
product
Broadband Current Probes
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.
-
product
Impedance meters
Electronic components meters for circuit verification in laboratories, technical schools and technical support centres.
-
product
Analog Tank Test Kit
4108
The voltmeter included in the kit, the “Model IA” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers a 0 - 2VDC range with a 10MΩ input impedance and the analog display presents a color divided scale for convenient indication as to whether or not a carbon-steel structure is receiving a suitable level of cathodic protection, with respect to the accepted 0.85V (850mV) threshold value.
-
product
Vector Network Analyzers
RF VNA to a Broadband VNA, from a Premium VNA with the highest performance and no compromises to a Value VNA that offers solid performance with suitable measurement speeds for an R&D environment. No matter what your application, Anritsu has your VNA needs covered. Choose with confidence from the pioneers in VNA measurements, introducing the Wiltron 310 Impedance Meter in 1965, and introducing the first broadband VNA, spanning 40 MHz to 65 GHz, in 1999. The first to cover a span from 40 kHz to 125 GHz from a single coaxial connector.
-
product
Benchtop LCR Meters
Keysight offers a wide range of benchtop LCR meters to meet your impedance measurement needs in the field of R&D, production, quality assurance, or incoming inspection. In addition to the high measurement performance and versatile functions of Keysight benchtop LCR meter, you will find the LCR accessories best suited for your measurement among a full lineup of Keysight impedance measurements.
-
product
FC Impedance Meters
designed for testing of the fuel cell with the small current (5 A or less), and not only the current-voltage characteristic test, the KFM2005 can easily measure for the impedance of a fuel cell using the AC impedance method, and the Cole-Cole plot. Using the measurement data of the Cole-cole plot, it is possible to calculate the circuit constant of the approximate equivalent circuit of the fuel cell. The built-in DC load (60W) is capable to operate from 0 V, and it can perform the test for the fuel cell up to 20V and 5A.
-
product
Short Termination, 4-Terminal Pair
42091A
Use for performance tests of the 4-terminal pair LCR meters and impedance analyzers.
-
product
Multifunction Electrical Installations Meter
MPI-520S
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
product
Impedance Meter, Audio, 200Ω, 2KΩ and 20KΩ scales
72-6948
Active device is essential for reliable installation of background music and paging systems in residences, offices buildings and public areas. Avoid costly service calls and amplifier damage by verifying actual speaker system impedance prior to operation. Unlike conventional volt/ohm meters, which measure DC resistance, this unit utilizes an internal 1KHz oscillator to measure true impedance. Accurately measure speaker lines that utilize impedance matching volume controls, switchers, transformers and passive crossovers. Because this unit accurately measures up to 20Kohm, it may also be utilized with 25V, 50V, 70V, and 100V speaker line transformers in commercial installations.
-
product
Four Terminal Pair Standard Resistor Set
42030A
The 42030A is a standard resistor set consisting of nine precision resistor standards which range from 1 mΩ to 100 kΩ. These resistors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.
-
product
Impedance Standards and Calibrators
Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.
-
product
Short Circuit Loop Impedance Meter
AMZC-306
Voltage measurement up to 750V and up to 250V with resolution 0,1V ; Measurements using Uni-Schuko adapter or test wires 1,2; 5; 10 and 20m ; Loop impedance measurement with resolution 0,01Ω and much more
-
product
Audio Frequency Oscillator
PD-5
2.5- 100 volt output6 position output voltage selectorCompatible with all "Mark" receivers (Mark II, III, IV, V)Pulse "Identifying" signalBattery charging circuit built-inLED impedance meter
-
product
Plus Precision LCR Meter
7600
The 7600 Plus LCR Meter performs precision impedance measurements over a frequency range of 10 Hz to 2 MHz. The LCR Meter can measure 14 different impedance parameters with 0.05% accuracy, meeting today's requirements for component and material testing. The ease of use and user-friendly menu programming makes the 7600 Plus ideal for applications in product development, incoming inspections, or production line testing.
-
product
General Purpose & Portable Impedance / LCR Meters
252
TEGAM''s Models 252, 253, and 254 are equivalent to ESI 252, 253, and 254. Perfect for component inspectors or manufacturing operators performing manual testing of inductors, capacitors, or resistors. An optional limits comparator is available for sorting components according to their measured parameters.
-
product
Transmission Measuring Set
Model 2031 / 2031A
- Compact Two in One Instrument with Level Oscillator & Level Meter- Selectable Spot Frequencies upto 4KHz- Digital dB Meter to Measure Level from-60dBm to +20dBm- Under / Over Range Indication- Built-in Rechargeable Battery- Lo-Batt Indication- Easy to Operate, Light in Weight & Portable- Selectable Spot Frequencies from 200Hz to 4000Hz- Extra Switchable Input & Output Impedance of 1120 ohms)
-
product
Audio Frequency Output Power Meter
PGP Electronics Private Limited
PGP Electronics AF Output Power meter, model 3301provides reliable measurement of Audio Frequency Output Power. The audio power output meter, measurable from 0.01mW to 30W in 12 decades with 10 different termination impedances with both balanced and un balanced inputs. The instrument is very useful to conduct students projects, design and test simple sub systems in laboratories. New improved design features provides reliable working even in adverse environments.
-
product
LCR Meters
An LCR meter measures impedance (inductance, capacitance and resistance) at spot frequencies.It is used for testing components and materials in R&D applications and in componet manufacturing.
-
product
AC/ DC mA Current Clamp-on Transducer
CA-60
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
product
50Hz-100kHz LCR Meter
11022/11025
Chroma Systems Solutions, Inc.
0.1% basic accuracyTransformer test parameters (11025), Turns Ratio, DCR, Mutual Inductance0Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz test frequencies21ms measurement time (≥100Hz)Agilent 4263B LCR Meter commands compatible4 different output resistance modes selectable for non-linear inductor and capacitor measuringHigh resolution in low impedance(0.01mΩ) and high accuracy 0.3% till 100mΩ rangeAdjustable DC bias current up to 200mA (constant 25Ω) (11025)1320 Bias Current Source directly control capability0.01mΩ ~ 99.99MΩ wide measurement range (4 1/2 digits)Dual frequency function (11022 option) for automatic productionBIAS comparator functionComparator function and 8/99 bin-sorting functionPass/fail judge result for automatic productionHandler interface trigger edge (rising/falling) programmableTest signal level monitor functionStandard RS-232, GPIB, and Handler I/FOpen/short zeroing, load correctionLabView® Driver
-
product
Earth Contact Resistance Tester
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
product
Chroma LCR Meters
Chroma Systems Solutions, Inc.
Some of the key features to look for in an LCR meter (also known as an impedance meter) are: accuracy, test frequency, measured parameters, test voltage and test current. Additionally, an easy to understand display of test results and the ability to access and use these results has become increasingly important. Component testing often requires much more than simply a resistance, capacitance or inductance value at a given test frequency and stimulus voltage. An LCR meter or impedance meter must have the flexibility to provide multi-parameters over wide frequency and voltage ranges.
-
product
HIGH FREQUENCY DC BIAS
6565 SERIES
The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.
