Filter Results By:
Products
Applications
Manufacturers
Harmonic
Sinusoidal component of a perodic wave or for a sine wave, it is an integral multiple frequency of the wave.
-
product
Digital Harmonics Clamp Tester
HWT-301
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Harmonics and leakage current measurements.*Up to 25th harmonics current and voltage measurements.*True rms reading for ACA and ACV.*Data-hold and Auto power off function.*Conform to IEC safety requirements.
-
product
3-Axis EMF Meter Ignore/Bandpass/Analyze Powerlines
DSP-523 Gaussmeter
The DSP-523 uses a powerful digital signal processor that sets a new standard for AC gaussmeters. Now you can ignore powerlines, bandpass powerlines and analyze powerline harmonics, all with one simple meter.
-
product
Portable Power Monitor/Recorder
As the world goes to a more Energy efficient mindset, products are needed to monitor each factory’s energy requirements. The CW500, CW240 and CW120 Power monitor series allows the customer to use a portable recording device to measure voltage, current, watts, VARs, VA, PF, PA, frequency, harmonics, and demand. This 1P2W to 3P4W power monitor provides a visual report of the current power situation to prevent major energy problem and utility over charges.
-
product
High Accuracy (0.045%) Precision Multi-Channel Harmonic Power Analyzer
PA910
The PA910 power analyzers offer expanded power analysis options. The PA910 offers ultra high 0.045% power accuracy for all channels and improved voltage and current self-heating adders over those of other power analyzers. In addition, the PA910 provides easy channel selection for the user while offering 100 full precision readings per second and measurement bandwidths sufficient to handle 5 MHz waveforms.
-
product
DR Range Broadband Power Amplifiers 10 KHZ - 400 MHZ
DR Series
Class A solid stateBroadband (instantaneous single band): 10 kHz 400 MHzTypical output power : 60 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 40 W and H<-20 dBc up to 250 MHz andP1dB > 25 W and H<-20 dBc from 250 MHz to 400 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
product
Sun Trackers
STR-series
EKO Sun Trackers are very compact, robust, relatively light weight and very power efficient. Inside the Sun Tracker a Harmonic Drive with advanced motion control unit is used on each output shaft. Harmonic drive is a leading drive technology for those application where high precision, durability, low backlash, high transmission ratios and torque is required. Due to its compact design and high transmission ratio small motors could be used to keep the power consumption low.
-
product
Harmonics And Flicker Measuring System
ProfLine Series
The Teseq ProfLine system is a complete and cost effective Harmonics and Flicker measurement test system which compiles to the latest IEC/EN standards, including IEC 61000-3-2 and IEC 61000-3-3. The programmable power generation capability of up to 45 kVA (90 kVA and 145 kVA sources comprise multiple 45 kVA units) provides more than ample power to cater for a wide range of Equipment Under Test (EUT).
-
product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-01
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
product
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger
SD750100G
Zhejiang Sandi Electric Co., Ltd
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger is for DC battery system charging station. With three-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. 50-500Vdc output voltage range optional, suitable for all types of batteries.FeaturesProduct Introduction：SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module.Unique function：● High efficiency over the full load range, full load efficiency greater than 95.5%● Wide output voltage range, 100-750VDC, suitable for a wide range of Lithium and lead acid battery● 5-inch LCD touch screen, easy to operate● Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operateMain features：● Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc.● Three phase active power factor correction technology, reduces the harmonic interference to the grid● Dual DSP design, achieve the full digital control, less components means high reliability● Wide input voltage range, allows operation in most poor grid conditions● Soft start charging and soft shutdown minimize the impact on the battery.● Input, output have protective circuit breaker switch● Module adopts hot pluggable design, which is convenient for maintenance.● CAN/RS485 interface (Optional)SpecificationModel SD750100GAC input Input system Three phases + PEVoltage range 280Vac ~500VacRated voltage 440VacFrequency range 50Hz/60HzMaximum current <74AITHD (total harmonic distortion) <5%DC output Output power 40KWVoltage range 50-750Vdc ( can set)Constant power output voltage range 400Vdc-750VdcOutput current range (A) 100A ( 1~100A can set)Output current limit 1-100A continuously adjustableSteady voltage precision <±0.5%Steady current precision ≤±1% (rated range of 20% ~ 100% for output load)Load regulation rate ≤±0.5%Startup overshoot ≤±3%Peak-to-peak value noise ≤1% (200~1000V, 0~20MHz)Display Indication Light Green LED: normal operation,Yellow LED: alarm, Red LED: failureDisplay language EnglishDisplay 5’ LCD touch screenPower factor and THD Power factor ≥0.90 Full-load output power of @20%~50%≥0.98 Full-load output power of @50%~100%≥0.99 Full-load output power, input nominal voltage and frequency of @100%THD ≤5% Full-load output power of @50%~100%Protection function input overvoltage Protection Over Under Voltage automatic shutdown and restart when voltage return normalOutput overvoltage protection Over Under Voltage automatic shutdown and restart when voltage return normalOver-temperature protection Automatic shutdown. Automatic restart when the temperature return to normalShort circuit protection Automatic shutdown and lock, need power off to restart to unlockEfficiency Under Rated input voltage ≥95.2％
-
product
Analog Earth Tester
FT3151
Earthing or grounding of electrical equipment is essential to maintain safety, protecting lives, as well as prevent damage to equipment. • Three-electrode method, Two-electrode method (Simple Measurement) • Wide measurement range for 0 to 1150 Ω, based on EN standard •Switchable measurement frequency to reduce the effects of power supply harmonics • Dramatically faster setup: Comes with improved grounding rods and cord winders. CAT II 300 V
-
product
18 Bit / 300 MS/s Arbitrary Waveform Generator
AWG18
The AWG18 is an 18 bit Arbitrary Waveform Generator for high-speed / high resolution waveform generation. This module features two dedicated signal paths. A DC to 100 MHz path which is optimized for accurate time domain and frequency domain measurements up to 30 MHz. And a dedicated AC path optimized for signals between 10 MHz to 100 MHz. In combination with the built-in filters it features a typical harmonics level of better than -80 dBc for the whole range.
-
-
product
Harmonic Mixers
These waveguide bandwidth harmonic mixers are designed for use with spectrum analzyers with diplexers, such as the Tektronix 492 and 494 and the Hewlett-Packard 8555A, 8565A and 8569A. They are also used as phase locking and receiver mixers for antenna measurement systems such as the Scientific Atlanta wide range receivers. When used with an external diplexer*, these harmonicmixers can be used to phase lock millimeter wave sources.
-
product
SHG Spectrometer
Second harmonic generation (SHG) is an effective technique for surface probing. By SHG, monolayer adsorbtion can be detected. With different input/output beam polarizations SHG can yield information on the average orientation of molecular adsorbates.
-
product
ESD Protection
Protection against electrostatic discharges (ESD) is part of EMC Immunity (Electro Magnetic Compatibility) requirements. It is the ability for equipment to properly operate in its electromagnetic environment by limiting the reception of electromagnetic energy that may cause physical damage. ESD can be either conducted under the form of a transient voltage or can be radiated due to its fast rising time: powerful harmonics will generate erratic behavior by the application by coupling with other signals. Printed circuit boards must be protected against the effects of electrostatic discharge.
-
product
LED Power Driver Tester
WT2080
WT2080 LED Power Driver Test Instrument is the comprehensive test instrument for LED drive power which is according to GB/T 24825-2009 and IEC 62384:2006. It can measure the following parameters: Input Characteristics Test (AC&DC), Output Characteristics Test (AC&DC), Output Start Characteristics Test (DC) and Harmonic Testing.
-
-
product
TRMS AC/DC Clamp-on Power
HT9023
HT9023 has been designed to measure AC, DC AC+DC current up to 1000A in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp also measures DC voltage up to 1500V, AC, AC+DC voltage up to 1000V, Active, Reactive and Apparent Power, Power Factor, Energy, voltage/current harmonic analysis up to the 25th with THD% calculation in balanced single-phase or three-phase systems.
-
product
Solid State GaN (Gallium Nitride) Amplifiers
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
product
Meter Testing
METES
Meter test systems with high accuracies of up to 0.02% and a wide measuring range for precise measurements in single- and three-phase applications. The meter test systems of the METES series are used to test the accuracy of Ferraris meters and electronic electricity meters under any operating conditions. The impact of system perturbations such as harmonics or flicker on the meter can be taken into consideration during tests.
-
product
Voltage Controlled Oscillators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
Power Quality Analyzer
Model PQA2100 / PQA2100E
Power Quality Analyzer is the professional portable device to measure and analyze the power system quality, supply the harmonics analysis and power quality data analysis, also provide big memory for the data storage, which is used to make the long term logger measuring to power system. The PC software can simply upload the data to PC for full analysis.
-
product
Multifunctional TRMS Power Meter
KM 6300
Kusam Electrical Industries Limited
Measurement of current, voltage, active, reactive and apparent power, Power factor, line frequency, energy, harmonic and Maximum Demand.
-
product
Air Core Smoothing Reactors
Smoothing Reactors are serially connected reactors inserted in DC systems to reduce harmonic currents and transient over currents and/or current ripples in DC systems.
-
product
Three-Phase AC Power Source 320 Vrms, 6 KVA, 550 Hz
AC6906L
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-02
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
product
Measurement
AC Selective Voltmeter
AC Selective Voltmeter is used for measuring AC voltage coming to the input channels of ADC modules and FFT spectrum analyzers. The specific feature of the AC selective voltmeter is perfomance of voltage measurements on the main signal-carrier frequency, which allows to eliminate the harmonics influence on the readings.
-
product
Test Compliance
CTS Series 3.2
AMETEK Programmable Power, Inc.
The CTS Series is a complete, turn-key compliance test system for EN IEC 1000-3-2 (Harmonics) Including A14, EN IEC 1000-3-3 (Flicker) and various EN IEC 1000-4 AC immunity tests. Consisting of an AC power source, a power analysis conditioning system (PACS) and a PC based data acquisition system, the CTS provides a complete turn-key solution for IEC testing. The Windows™ based CTS software performs the IEC tests and generates detailed test reports. Comprehensive data files are stored on disk to allow post test analysis.
-
product
Energy and Harmonics Analyzer
STAR3
STAR 3 is a high quality 96x96mm panel energy analyser provides brilliant features at a price never reached before. The new bright red LCD display, the harmonic analysis, the wide set of measured parameters including the THD available in all the models, the multi-protocol capability of the RS485 port and the high accuracy class 0.5%, the 3 years-warranty period, allow to consider the STAR 3 the new state of art of the panel analysers market
-
product
Portable Test System
MT786
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
