Filter Results By:
Products
Applications
Manufacturers
- Optomistic Products
product
Universal LightProbe Sensors
Optomistic Products’ unique Two-Part Solution fulfills almost every LED test requirement you may have.First, determine your test requirements. For example: LED color and intensity test with an analog output, or, LED ON/OFF status with a digital output, etc. Then, choose from the range of Sensors listed below to address those requirements.
-
product
Force Sensors
Our force sensors are indicated for use in modal and structural analysis, process control, and general-purpose dynamic force measurements. See our range of charge modes and IEPE force sensors.
-
product
Force Sensors
Here at Flintec, our force sensor range provides solutions that integrate effectively into a wide variety of industrial applications. They include customized load pins, extensometers, torque sensors and a range of miniature force sensors.
-
product
Displacement Transducers
Procter & Chester Measurements Ltd
Pressure: Measures gas or liquid pressure. Pressure is an expression of the force required to stop a fluid from expanding. The transducer generates a signal from the pressure imposed upon it. Torque: Measures the torque (or twisting motion) on a static or rotating system. The static torque element has little movement and therefore more economic to manufacture and purchase. Rotary or dynamic torque is more complicated as the signal needs to be transferred using slip rings, wireless telemetry or rotary transformers/inductance technology so that the strain gauged shaft can continuously rotate. Displacement: Measures distance. The displacement transducers that PCM offer are slightly different to standard units. They have a strain gauge/wheatstone bridge. The benefit here is that if the customer has existing electronics that uses strain gauge/load cell technology, they can use them with these sensors.
-
-
product
Triaxial Linear Accelerometers
Columbia Research Laboratories
The Triaxial Force Balance Linear Accelerometers range from general purpose, low cost sensors, capable of measuring DC and low frequency acceleration simultaneously in three axes, to Miniature Airborne, Highly Reliable Sensors that operate from +24 to +32VDC Aircraft power. Also offered are compact, premium performance, extremely rugged sensors, well suited for demanding missile and airborne applications.
-
product
Measurement, Communications & Testing
Process & Analytical Instruments division of AMETEK
Measurement Communications & Testing provides the design, integration and installation of critical communication systems, workflow, life-safety solutions and calibration instruments for temperature, pressure and process control. It also is a leader in level measurement devices, continuous position sensors, hardness testers, force measurement devices and retractable cord reels. In addition, it offers a line of weathering test instrumentation along with laboratory and outdoor testing services.
-
product
Quartz ICP® Links
Link-style sensors measure dynamic compression and tension. They are constructed using a force ring that is under compressive pre-load between threaded mounting hardware. The threaded mounting on both ends of the sensor supports integrated link-style installations. Versions offering full-scale measurements of 10 lb to 50k lb (45 N to 220k N) compression and 30k lb (130k N) tension are available.
-
product
Force Sensors In S-form For Pull/push Direction
INELTA Sensorsysteme GmbH & Co. KG
With very small space requirement and high breaking force made from tempered stainless steel, suitable for measuring medium to high forces. Easy integration and mounting by threaded bores.
-
product
Force Sensors
Custom FlexiForce
With its paper-thin construction, flexibility, and force sensing ability, the FlexiForce FSR Sensor can measure force between almost any two surfaces and is durable enough to stand up to most environments. The unique construction and durability of these FSR sensors enables Tekscan to create custom-designed FSR sensors to meet the specific needs of many OEM customers. We also offer standard off-the-shelf sensor products for prototyping and low-quantity requirements.
-
product
Signal Conditioner
INELTA Sensorsysteme GmbH & Co. KG
Signal Conditioning of LVDT Displacement Sensors and Force Sensors
-
product
Force Sensors
TE Connectivity (TE) designs and manufactures force sensors for applications that require high performance or unique packaging, including electro-mechanical flight control, test and measurement and ultra-low cost OEM load cells for medium to high volumes. Based on our proprietary piezoresistive silicon strain gage (Microfused) technology, our sensors combine durability and long-term stability in extremely low cost packages.
-
product
Load Cells
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
product
Airlock Control System
The system is built on the basis of a panel computer with a touch screen, performing the functions of a user interface and recording the measured parameters. The stand is equipped with gate drives and a set of sensors (pressure, flow rate, force). Real-time gate control is implemented on the basis of the R-series board; for input and conversion of analog signals from the sensors, an expansion cage of the cRIO-9151 R-series boards is used.
-
product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
product
Signal Conditioner in DIN Rail Housing
Series IMA2
INELTA Sensorsysteme GmbH & Co. KG
For LVDT Displacement Sensors, DMS Force Sensors and potentiometric Sensors
-
product
3-Component Quartz Force Rings
260 Series
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
product
Force Sensors, Controls & Switches
Direct caliper motor/spindle integration for Brake by Wire systemsExtra-small form factor MSG sensors that weigh less than five gramsFacilitating system-level miniaturizationAdvanced button-type sensors designed to lower costs and improve accuracy
-
product
Force Sensors For Pull/push Direction
INELTA Sensorsysteme GmbH & Co. KG
The force sensors can be integrated easily and uncomplicatedly by the regular standard thread.
-
product
Shear Beam Force Sensors For Pull/push Direction
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
product
Modeling Capacitors, Inductors, Insulators, Coils, Motors, and Sensors
AC/DC Module
The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.
-
product
Pressure / Force Sensors
Panasonic Industrial Devices Sales Company of America
Panasonic offers high precision Pressure Sensors for industrial, medical, clean room and other gauge equipment uses. Some include a built-in amplifier and compensating circuit in a compact, low and high pressure Sensor with high accuracy and reliability.
-
product
Force Sensors
Piezoelectric force sensors, respectively piezoelectric force transducers or load cells, are perfectly suited for the precise measurement of compressive and tensile forces, both in highly dynamic applications and in quasi-static processes. In universities and industry, for basic research or quality assurance: exact data is always essential in order to measure force characteristics and make processes more cost-effective. Thanks to their rugged design, piezoelectric force sensors from Kistler keep precise track of quasi-static and highly dynamic force processes, even when conditions are difficult. Our force sensors can also handle simultaneous measurements of multiple orthogonal force components.
-
product
Linear Accelerometers
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
product
Adhesion Tester
Surf-2
Rtec Adhesion Tester is a turn key solution to measure Pull up Adhesion force, Work of Adhesion and Shear Adhesion of materials. Equipped with Ultra-Sensitive Capacitance Load Cells this tester provides µN level resolution with forces up to 5N. The High-Resolution sensors allow characterization of large samples over macroscopic length scales to study the effect of texture and other surface modifications. Integrated with High Resolution Inverted Camera, it allows the researchers to measure Contact Area vs. Force making it extremely useful in measuring Adhesion of Soft Materials, Biomimetics and Hydrogels.
-
product
Force Sensors
Specially designed for overseeing manufacturing processes. It measures with high consistency the regularity of compression load generated when fitting pieces.
-
product
Performance Exams
Sturdy sheet steel housing with safety door and electrically driven base with built-on sample mold. The compaction takes place via a rolling segment with force / path-controlled drive device from above. The sample mold and the rolling segment are equipped with software controlled heating. The measurement of force and displacement is done by electronic sensors. The entire compaction process is controlled with Windows software and PC via preselected sequence programs.
-
product
Load Monitoring Units (LMUs)
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
product
Miniature Quartz Force Sensors
Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.
-
product
DMS Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
Force Sensors
Is defined as a transducer that converts an input mechanical force into an electrical output signal. Force Sensors are also commonly known as Force Transducers.
