Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI Fault Insertion Matrix Modules
All of our fault insertion matrices feature a breakout arrangement that allows faults to be attached to the sensor lines via the Y axis. This includes the breaking of a connection or the adding of a series defect – all of which can simulate connectivity problems in the system. The three pin breakout versions allow the connection to be swapped for a “bad” sensor simulation.
-
product
Test Phone - Professional TS54 Pro
CZ20154
The CZ20154 is the top of the range in latest design technology providing voice, data, and video technicians/engineers all the functionality essential in a test set. Buttinskis are now required to deal with modern high speed digital services - something this test phone has been specifically designed for. On top of all the tests performed by the CZ20123, TDR length measurement to 900m is included for the first time on a buttinski. Not only can you measure cable length but you can identify the fault location of an open or a short. Further, tone generation is included as standard providing 5 different search tones and SmartToneR that confirms you have located the correct pair. Never before has this level of features been available in a buttinski. No longer do you need to carry a separate butt set, TDR, toner, and identifier - this buttinski does it all in the one tool !
-
product
Fault Trapper
#TFT100
Stop guessing about circuit breaker tripping issues. See why, when and where a circuit breaker trips. For the first time, you can detect the type of fault, and locate the position of an electrical “event” that causes intermittent and persistent circuit breaker trips, and No Fault Found (NFF) conditions. The critical information needed to reduce […]
-
product
Overhead Line Fault Locators
We're professional overhead line fault locator manufacturers and producers in China, supplying the best customized service. Feel free to buy high quality overhead line fault locator from our factory. All our portable products used in utility locations are with CE certification.
-
product
Valves Testing Equipment
A PD or PHD Pinhole Detector is ideal as it has an audible alarm which sounds when a fault is found. Additionally, the test voltage can be set accurately, which is particularly important when testing thin linings. A DCCT mains-powered porosity tester can be used if the process needs to be incorporated into a production line
-
product
VLF test system
BAUR PHG 80 portable
BAUR Prüf- und Messtechnik GmbH
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
product
Smart Electric Tester
SET-12
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
product
Current Protection Relay
The main earth fault protection relays in distributions systems, power stations & large manufacturing / processing plants can fail to detect a high impedance break down to earth causing hazard to human life & potential damage to plant & equipment. In these & other situations demanding extra sensitive earth fault protection, using solid state techniques, can be applied to detect earth currents down to 0.5% of the CT nominal current.
-
product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
HD Tester with VGA, Audio, Video, HD-TVI
M-HD-360A
Fuzhou Metricu Technology Co Ltd
Analog camera testHD-TVI camera test, HD-CVI camera test, AHD camera testDC12V 1A power outputVGA input, support 1920 x 1200P 60FPSAuto HD, auto recognize HD coax camera type and resolutionUTP cable test, detect the near-end, mid-end and far-end fault point of the network cable crystal head
-
product
Time Domain Reflectometer
ETDR 10A-2
Compact dual channel precision full function portable easy to useTDR for fault location on balanced loaded and unloaded cables.
-
-
product
Portable Waveform Recorder
HTLB-602 / 371
Wuhan Huatian Electric Power Automation Co., Ltd.
Intelligent instrument integrating fault recording, generator characteristic test and other functions.
-
product
Fault Diagnostics in Power-Off State
QT55
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
product
Voyager Intermittent Fault Detector
The Voyager includes a spread spectrum TDR so that the fault can be located. Once an intermittent is detected, the TDR is immediately connected to the failed test point and used to determine the distance to the fault.
-
product
Visual Fault Locator VFL
X4007
X-4007 series visual fault locator is used for the measurement in single-mode or multi-mode fibers. It features a rugged design, a universal connector and an accurate measurement.
-
product
Recloser Controls
Schweitzer Engineering Laboratories, Inc.
Recloser controls provide fault location, isolation, and system restoration using protection and communications capabilities, such as Automatic Network Reconfiguration and single- and three-phase tripping. They allow you to automatically reconfigure your distribution system to isolate faults, quickly restore service, and reduce customer impact.
-
product
PXI Dual Bus 64-Chan 2A Fault Insertion Switch, N/O Through Relays
40-190B-402
The Dual Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel.
-
product
Volt Gradient Detector
K&S Engineering and Scientific Ltd
The Voltage Gradient Unit is used to pinpoint faults by the pool of potential methods
-
product
Integral Intelligent Flame Detector
FS-100
FS-100 utilizes SMT technology which integrates a photoelectric sensor, a microprocessor, and a Human-Computer Interface (HCI) and an output interface together, sending out various outputs including an ON/OFF flame signal, a fault signal, a 4-20mA signal, and an RS-485 output (meets the MODBUS standard) via the quick connector.
-
product
Cable Route Tracing and Identification
Cable pinpointers and fault locators from Megger make the process of cable route tracing and identification quicker and more accurate. These pinpointing systems are portable for everyday fieldwork and provide services from power and telecoms to water, rail and gas utilities. HV and LV buried cables can be traced to a depth of up to 5m.
-
-
product
Advanced Data Acquisition And Control System
ADACS
This high-speed damage-control system was built around Arc Fault Detect and Continuous Thermal Monitoring (AFD/CTM) from the Johns Hopkins Applied Physics Laboratory. When AFD/CTM detects dangerous arc faults — powerful discharges of electricity between conductors — the ADACS system immediately cuts power to the affected circuit before it can damage equipment or injure nearby personnel. Altogether, the system prevents loss of life, preserves countless repair dollars and assures continuous readiness.
-
product
Ethernet Speed Certifier & Network Tester
Offers a complete solution to test and speed certify the data-carrying capabilities of Ethernet network cables up to 1 Gb/s by testing for noise in the network, detecting faults in the cable wiring, and ensuring that cables are able to support the speed capabilities of active equipment.
-
product
Tactical Radio Test Set
CTS-6010
The CTS-6010 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
product
Cable Assembly, Twisted Pair, Differential Signals, 78-Pin D-Type Male To Female, 0.5m
A078DMR-078DFR-9A050
The A078DMR-078DFR-9A050 is a 78-Pin Male to Female D-Type Cable Assembly with twisted signal pairs suitable for differentialsignals and is designed to be used with Pickering's 40-200 fault insertion switch.
-
product
PXI BRIC8 FIBO Matrix Dual 120x4 3pin brkout
40-592A-106
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
PXI-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
778858-01
96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module—The PXI‑6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Geologic Stresses on Faults & Fractures Software
3DStress®
3DStress® provides a user-friendly and interactive tool to investigate geologic stress states and effects on developing and reactivating faults and fractures. Components include Mohr circle plots with Hoek-Brown failure criteria, stress-ratio plots, stereonet and three-dimensional (3D) visualization tools to enable the user to illustrate hypothetical situations or complex real-world fault and fracture systems, and a patented stress inversion algorithm that does not require slip direction information.
