Filter Results By:
Products
Applications
Manufacturers
Electro-Chemical
chemical action when combined with electricity.
- PalmSens BV
product
Potentiostat / Galvanostat / Impedance Analyzer
PalmSens4
PalmSens4, is a USB and battery powered Potentiostat, Galvanostat, and optional a Frequency Response Analyser (FRA) for Electrochemical Impedance Spectroscopy (EIS). The PalmSens4 has a large potential range (-5V to 5V or -10V to 10V) and current range (100 pA to 10 mA) with a high resolution and low noise. This instrument is a complete laboratory instrument but its compact and rugged design makes it also ideal for field work.
-
product
Scanning Electro-chemical Microscope
920D
The scanning electrochemical microscope (SECM) was introduced in 19891 as an instrument that could examine chemistry at high resolution near interfaces. By detecting reactions that occur at a small electrode (the tip) as it is scanned in close proximity to a surface, the SECM can be employed to obtain chemical reactivity images of surfaces and quantitative measurements of reaction rates.
-
product
DS Sensor
Z-Gard DS Sensor
The Z-Gard DS Sensor is designed to detect the presence of carbon monoxide and nitrogen dioxide gases in parking garages, vehicle storage areas or wherever else these two toxic gases could be found. These sensors employ electrochemical sensors which generate a representative output signal proportional to the calibrated operating range.
-
product
Reference Electrodes
Reference electrodes are widely used as: electrochemical measurements (CV, LSV, DPV, etc.) electrochemical devices (detectors for HPLC, biosensor, etc.)
-
product
Chloride Test System
C-CL-2000
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
product
Water Quality Products
When you need to perform critical water testing, look to us for an extensive selection of electrochemical meters, controllers, probes, electrodes, test kits, buffers, and standards. Our field and laboratory instrumentation include water analysis instruments for dissolved oxygen, temperature, pH, conductivity, salinity, and turbidity.
-
product
DigiElch Electrochemical Simulation Software
DigiElch 8 from ElchSoft is an electrochemical simulation program for a wide variety of systems involving charge transfer reactions, adsorption, and charge-coupled chemical reactions such as proton-coupled electron-transfer (PCET). A demonstration version of DigiElch 8 is available.
-
product
Electrochemistry
Portable Line
Portable Line potentiostats/galvanostats combine electrochemical research in the laboratory with on-site research using well-established electrochemical techniques.These small and affordable portable instruments enable you to develop applications for your specific research needs. Portable Line instruments are an ideal solution in many research areas, such as (bio)sensor, corrosion, or (bio)fuel cell.
-
product
Time-Resolved Electrochemical Quartz Crystal Microbalance
400C Series
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
product
Power Potentiostat/Galvanostat
1100C
The Model 1100B series power potentiostat/galvanostat is designed for electrochemical applications that require relatively large current and high compliance voltage, such as battery studies, corrosion, electrolysis, and electroplating. The current range is 2 A, and the compliance voltage is 25 V. The instrument contains a high speed digital function generator, a fast data acquisition system, filters for current signals, iR compensation circuitry, a potentiostat, and a galvanostat (Model 1140B). The potential control range is 10 V.
-
product
Electrochemical Measurements
A portable pH-meter from CHAUVIN ARNOUX is ideal for mobile applications: in the field, in the laboratory or in production. It can be used for quick, accurate, professional measurements of pH, Redox potential and temperature.
-
product
Electrochemical Converter
C800
The Control 800 series of electrochemical converters combines high performance digital conductivity and analog pH measurements with intuitive operation. It has been designed for easy integration into skids and panels to cover a wide range of bioprocess applications in both, conventional stainless steel and single-use systems.
-
product
Corosion Testing
Materials Evaluation and Engineering
Electrochemical corrosion experiments can provide a variety of data related to the pitting, crevice corrosion, and passivation behavior for specific sample/solution combinations. These data are useful in selecting materials and/or determining how manufacturing processes affect corrosion properties.
-
product
Transmitter Monitors Carbon Monoxide
CO-R
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
product
AVL Battery Test Systems
Supplied as either a free-standing test rig or as a containerized solution, the battery test system supports the evaluation and life-time investigation of electrochemical energy storage systems used in hybrid and electric vehicles.
-
product
Process Trace Oxygen Analyzer
GNL-IN90
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
GNL-IN90 trace oxygen analyzer adopts the electrochemical principle, can test oxygen concentration in 0-10/100/1000ppm - See more at: http://en.ci-ele.com/8aedb8bf-ef48-4f8c-127a-797c939a6181/5e56e024-971a-1704-6125-0787e9eca192.shtml#sthash.SNo0Q2tG.dpuf
-
product
Formaldehyde Meter
-Backlit LCD displays simultaneously formaldehyde (HCHO), temperature, humidity, easy to monitor.-Occupational safety monitoring shows TWA (8 hours) and STEL (15 mins).-Use high-precision electrochemical sensors.-The maximum / minimum / average hold.-Stores 200 records manually.-Data hold.-Formaldehyde maximum and minimum alarm value setting.
-
product
Materials And Chemical Analysis
Anderson Materials Evaluation, Inc.
Materials characterization, failure analysis, quality control, and materials and process development services are offered. Our analytical techniques allow us to assess elemental and chemical material composition, thermal properties, coating thickness, electrochemical properties, surface chemistry, surface wetting, corrosion rates and pitting potentials, contamination and degradation problems, metallography, fractography, phase transitions, static coefficient of friction, adhesive bonding strength and causes of adhesive bonding failures, surface tension and surface energy, tensile and compressive strength, bend deflection, lapshear strength, elasticity properties, UV and visible light absorption and reflection, density and porosity, and many other material properties integral to improving your products.
-
product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
product
PARSTAT MC Multichannel Potentiostat
The PARSTAT® MC (PMC) is the most modular and robust multi-channel electrochemical testing platform on the market.The PMC chassis provides a robust environment up to 10 modules, up to 20 channels.
-
product
Bipotentiostat
700E
The Model 700D series are computerized general purpose potentiostat / bipotentiostat / galvanostat instruments. A typical application involves a rotating ring-disk electrode (RRDE), but these systems can also be used for other applications where dual channel measurements are essential, such as dual channel electrochemical detection.
-
product
Electrochemical Analyzer
EC Epsilon EClipse
The Epsilon EClipse™ is the latest electrochemical analyzer manufactured by BASi. It is a potentiostat/galvanostat with a second working electrode for bipotentiostat measurements. It comes with software that enables the most popular electrochemical techniques such as cyclic voltammetry, chronoamperometry, and chronopotentiometry (select Techniques below for a more complete list). The Basic Plus software can be purchased to enable pulsed voltammetry and stripping voltammetry techniques.
-
product
Addon Cards
Fit the IM6/Zennium electrochemical workstation to your application. Control external potentiostats, capture additional physical properties or enhance your system to a true parallel impedance analyzer.
-
product
Cells and Electrodes
Electrochemical cells are designed to their special purpose. The method, the matter and their reactions as well as the environmental conditions define the limitations and demands for electrochemical cells and the electrodes. Standard corrosion testing cells may have a large volume, since corrosion products shall not change the solution grossly during the test. On the other hand, it may be valuable to collect corrosion products - then a very small volume is desired ("eluation cell"). Special corrosion tests for pitting reqiure a setup where undesired crevice corrosion is excluded ("Avesta cell" , "Quarfort Cell" or "Flushed port cell". Or you want to investigate in crevice corrosion, then the cell design should meet such conditions. Have a look to the variety of cells shown here, and call us if you have a special task where a fresh design is required.
-
product
Signal Generators
"Signal generator" is the generic name for instruments which produce time - dependent voltages which are used to stimulate other processes, e.g. electrochemical reactions. Standard types are ramp generators, also called sweep generators which produce linearly varying voltages, pulsgenerators, sine wave generators and arbitrary signal generators. Generally, D/A - converters are also to be regarded as "signal generators". This page, however, deals with stand-alone signal generators only.
-
product
Electrochemical Migration (ECM) Testing
Testing for electrochemical migration (ECM) would occur in the case of a field failure return. Metal migration between isolated conductors on a completed printed circuit assembly may produce electrical shorts.Why does this growth occur and what do you need to look for? Basically, we need to know if our assemblies are “dirty.” By dirty, we mean littered with ions. Ions on printed circuit assembly surfaces can cause short circuits. In simple terms, shorts occur when the space between the conductors is bridged by dendrites formed by re-deposited metal ions. This metal migration is best described by IPC as a reverse plating of the conductors in the presence of ions, water and an electrical potential.
-
product
The Golden STM
*Golden (chemically resistive) vibration isolated STM body with implemented preamplifier*Computer with PCI board based SPM controller *Anfatec Scan & Anfatec Present*19“ STM controller (extra low noise 24 bit converters)*HV display for z-direction*High voltage amplifiers for the x-y-tube scanning*Optional: PC controlled bi-potentiostat and electrochemical cell
-
product
EIS Battery Analyzer
BA8100
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
product
Scanning Probe Workstations.
BioLogic has over 25 years of experience producing scanning probe electrochemistry instruments. Initially this included a number of single technique instruments, with the first modular scanning electrochemical workstation, the M370, introduced in 2006, under the Uniscan name.Scanning probe electrochemistry has found use in academic and commercial research settings. It is applicable in any field in which bulk electrochemical measurements have been used. Scanning probe electrochemistry has found widespread use in: Corrosion and coatings, Biology, including biosensors and biotechnology, Batteries, fuel cells and photovoltaics, Materials, Catalysis
-
product
Oxygen Analyser
Rapidox 1100
The Rapidox 1100 oxygen gas analyser is the company’s most cost-effective and versatile range of gas analysers fitted with either zirconia or electrochemical type gas sensor.The zirconia oxygen sensor is the most common solution providing fast and accurate gas analysis over the range 1ppm to 30% O2 and is particularly suitable for aggressive industrial applications.Users have a choice of two electrochemical oxygen sensors: one for low ppm measurements of 1ppm up to 1% and another for high percent measurements in the 1ppm to 30% oxygen range. Electrochemical sensors are ideal for high oxygen applications or ppm applications where VOC’s, flammable gases, CO, H2 or He is present in the gas sample. A special “oxygen clean” version of the high range analyser is also available.Together the three sensor types offer an oxygen measuring solution for almost any application possible.
