Filter Results By:
Products
Applications
Manufacturers
Earth Bond
Checks a ground circuit's ability to handle fault current in the event of insulation failure.
-
product
Electrical Installation Testers
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
product
Medical System
Sentinel I
Chroma Systems Solutions, Inc.
The Sentinel I System provides fully automated Electrical Safety Testing to IEC/EN/UL/CSA 60601-1. This system is ideal for testing medical products with one or no patient connections or low volume production where operators can manually change leads between different patient connections. This is a 5 in one Hipot test system that can test Hipot, Ground Bond, Insulation Resistance, Patient Leakage, Earth Line Leakage, Enclosure Leakage and Patient Auxiliary Leakage.
-
product
Electrical Safety Test Equipment
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
product
Safety Test Panel for Geyser
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of Geyser. In addition to the conventional safety tests, test for performance is also included.
-
product
Safety Test Panel for Water Cooler
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of washing machines. In addition to the conventional safety tests, test for performance is also included.
-
product
Earth Bond Test Set
EC-12
The Earth bond test is a basic safety test prescribed in many standards to test samples for the integrity of earthing continuity throughout the sample.
-
product
Bond Tester
Sigma
Sigma is the most advanced bond tester. It comes with game-changing automation capabilities and high specifications
-
product
Bond Testers
Has automated the test process with microprocessor-controlled data acquisition. Designed to provide the expected internal bond strength for various types of paper, coated products and paperboard, this instrument measures the impact energy imparted to the specimen. The machine consists of a base, sample-preparation press, tape dispenser, dual-range pendulum (0 to 0.325 ft. lbs. and 0 to 0.650 ft. lbs.) and Digital Display. Internal Bond software is available.
-
product
Ground Bond Tester
HYAMP® Series
HYAMP III includes productivity-enhancing features and proven safety technology to reduce the compliance bottleneck on the production line. All models verify the integrity of your product's ground circuity with accurate 4-wire measurements and offset capability.
-
product
Bond Alignment Systems
With the invention of the world’s first double sided alignment system in 1985, EV Group has revolutionized MEMS technology and set worldwide industry standards in aligned wafer bonding by separating the alignment and bonding process. This process separation results in higher flexibility and universal application of the wafer bonding equipment. The EVG bond alignment systems offer highest precision, flexibility, ease of use and modular upgrade capability and have been qualified in numerous high throughput production environments. The precision of EVG bond aligners accommodates most demanding alignment processes in MEMS production and in emerging fields like 3D integration applications.
-
product
Earth Leakage
National Meter Industries Inc.
This new range features a series of improvements intended in particular for installing unitson switchboards. Along with the usual attachment elements, this unit can be installed onDIN rails using an accessory, which facilitates its installation.
-
product
AC Ground Bond Tester
448
Our 448 model is a 4-in-1 tester with 500VA AC Hipot, DC Hipot, Insulation Resistance and Ground Bond testing capabilities. The 448 is capable of a 500VA AC Hipot output to comply with 100mA leakage current test compliance requirements. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application.
-
product
Earth Resistance Testers
.Multi Test Voltage.Conductor resistance measurement(DET4300).Soil resistivity measurement(DET4300).LCD background light.Data hold.Working LED indicator.Low battery warning.Function symbol display
-
product
Earth resistivity meter
16GL-N
Last release of a very popular family of earth resistivity meters, this 16 bits geoelectrical instrument represents a really performing and affordable solution for Vertical Electrical Soundings at medium and great depth. Reliable and lightweight, 16GL-N is characterized by really first-rate performances, even if it remains extremely easy to use. The possibility to download data through USB enables a quick interpretation with the data inversion software. It is recommended, as to exploit its capabilities, to use it in conjunction with one or more P-100-N rechargeable accumulators.
-
product
Earth Resistance Tester
2678
Shenzhen Chuangxin Instruments Co., Ltd.
RK2678 series Earth Resistance Tester is used to measure the grounding resistance of the electrical equipments’ internal. It’s suitable for measuring the ground wire resistance of the various motors, electrical appliances, instruments and meters, household appliances and other equipment enclosure etc.
-
product
Earth Tester
TAURUS PRECIOHM ET
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
product
Analog Earth Tester
FT3151
Earthing or grounding of electrical equipment is essential to maintain safety, protecting lives, as well as prevent damage to equipment. • Three-electrode method, Two-electrode method (Simple Measurement) • Wide measurement range for 0 to 1150 Ω, based on EN standard •Switchable measurement frequency to reduce the effects of power supply harmonics • Dramatically faster setup: Comes with improved grounding rods and cord winders. CAT II 300 V
-
product
Earth Ground Tester
Weshine Electric Manufacturing Co., Ltd
UT520 series can perform precise 3-wire and simple 2-wire earth resistance measurement for power and electrical systems, lightning protection equipment, and ground system of all electrical equipment.
-
product
Bond Testing
Our complete line of bond testing (BT) flaw detectors provides unmatched capabilities for the location of discontinuities and other flaws in composite structures. We offer a wide range of measurement features and application-specific options for flaw detection.
-
product
Digital Earth Resistance Testers
ST-1520
Capable of measuring earth voltage.2mA measuring current permits the testing of earth resistance without tripping earth leakage current circuit breakers in the circuit.Auto power off function.The timer operates automatically for approximately three to five minutes when the "push button switch" and "timer on button" are pressed together.
-
product
Fixed GEO Earth Stations
Kratos Defense & Security Solutions, Inc.
Kratos provides a broad range of fixed earth stations ranging from 3.5m to 18m and configured in receive-transmit or receive-only mode. These antennas offer outstanding electrical performance and exceptional versatility to support low PIM at certain Ku bands and all X-band systems.
-
product
Earth Testers
Sanwa Electric Instrument Co., Ltd
Most facilities have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. A ground electrode provides the contact between the electrical system and the earth.
-
product
Ground Bond Tester
260 Series
Our 260 Series makes Ground Bond testing simple. We offer two models so that you can have a simple and easy-to-use Ground Bond tester that provides the output current you need to satisfy NRTL specifications. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 260 Series can easily be deployed in both laboratory and production line environments.
-
product
Earth Resistance Tester
Weshine Electric Manufacturing Co., Ltd
specially designed and manufactured for the field measurement of ground resistance, adopts digital and micro-processing technology, 3 wire or 2 wire method to measure ground resistance, with unique calibration function for wire resistance, anti-interference ability and environmental adaptability, to ensure the long-term measurement of high precision, high stability and reliability; The instrument out shell adopts waterproof protection case, anti-collision, anti-fall, waterproof (protection grade IP65),which is strong, safe and durable, the instrument is also equipped with large capacity rechargeable lithium battery pack, especially suitable for outdoor construction site to use.
-
product
Earth Leakage Relays
Variable Earth Leakage Relays in compact 35mm din rail mounting cases for use on 3 phase electrical systems.
-
product
AC Ground Bond Testers
440 Series
The 440 Series provides advanced 4-in-1 test capability in a convenient one-box solution. This new series performs AC Hipot (448 - 500 VA), DC Hipot, Insulation Resistance and 40A AC Ground Bond tests while taking up minimal production line space. The 440 Series is simple and easy-to-use; reducing setup time and increasing production line throughput for your application. With multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Learn about our 5 Year Warranty.
-
product
Clamp Earth Tester with Bluetooth Connection
MET-10X
MULTI MEASURING INSTRUMENTS Co., Ltd.
Next clamp-type grounding resistance tester that can connect to a smartphone via Bluetooth and save data on an our cloud server.
-
product
Earth Ground Clamp Meter
T2000
T2000 is a professional clamps specially developed to evaluate resistance of earth rods with no need to disconnect any part of the system (STAKELESS METHOD)
-
product
Guardian Ground Bond Tester
19572
Chroma Systems Solutions, Inc.
Wide resistance measurement range : 0.1 ~ 510 mΩHigh performance AC current output : 45 ACompact size ground bond testerProvide reliable and stable test resultsBuilt-in resistance compensation functionStandard RS-232 interfaceOptional GPIB InterfaceCompatible with the model 19070 series Hipot Tester2-Year factory warranty
-
product
Earth Leakage Relay
Nippen Electrical Instruments Co.
NIPPEN's Earth Resistance Testers are used for measuring earth electrode resistance, soil resistance, earth continuity, neutral and earth loop resistance, resistance of various components etc.They are used in Railways, Defence, Utilities, Power Plants, Geological Surveys and other Industries.Direct reading type models SET/DET/TET provide direct readings of resistance on moving coil type meters, having a linear scale, 70mm long knife edge pointer and an external zero adjustment.
