Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
TiePieSCOPE HS805, 2 Ch, 32MS/ch, 1 GS/s, 250MHz BW, USB Digital Storage Oscilloscope, AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS805
The TiePieSCOPE HS805 is a portable USB oscilloscope that combines a high sampling speed (1 GSamples/s on one channel, 500 MSamples/sec on two channels) with a long record of 32 MiSamples per channel. That allows you to capture long, complex signal patterns at full speed. The 250 MHz high bandwidth ensures that the signals are measured accurately and without distortion.
-
product
Test Solutions Services
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
product
Optical Tester
Model C
The Model C Optical Tester is just such a device. Extremely small geometric distortion and focal length deviation can be viewed and measured easily.
-
product
Single Channel Signal Buffer Module
Alliance Support Partners, Inc.
Signal quality problems caused by mismatched impedance can result in intermittent measurements and faulty diagnostics. This is most often observed when transporting a test program from one system to another, such as re-hosting it from an older generation system to a new one. The primary root cause of the impedance mismatch is the signal path from the UUT to the measurement instrument. The switching system technology often is responsible for much of the distortion. The Signal Buffer Module (SBM) is designed to receive a signal from the UUT with high impedance output and accurately reproduced it at the output for delivery to the measurement instrument. The SBM output matches the 50 ohm input impedance of most measurement instruments and result in significantly reduced signal distortion.
-
product
Modulation Distortion Up To 53 GHz
S95070B
S95070B software enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 53 GHz. The wide dynamic range and vector error correction of the PXI VNA results in an extremely low residual EVM from the test setup, giving you a complete picture of your device’s performance without test system interference. S95070B software measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals through spectral correlation between the input and output spectrum, without doing demodulation. Integration with the PXI VNA’s measurement flexibility enables you to do quick modulation distortion measurements along with traditional VNA tests.
-
product
Low Distortion 1kW Power Source With UK/Schuko/USA Socket.
AC1000A
Provides an EN61000–3–2 compliant source1000W power capability at 230VUp to 4·4A rms load current and up to 10A peak currentsComprehensive overload protectionConnection via standard power connectors
-
product
Fixed Attenuator
Are electronic devices used to reduce the power level of a signal by a fixed amount with minimal distortion. They are designed to have a fixed and unchangeable attenuation.
-
product
Robotics and Machine Vision Standards
Accuracy in machine vision systems is critical to achieving strategic goals regarding quality, efficiency, and consistency. Use our ACCUplace product lines to calibrate vision systems’ distortion, placement/alignment, or other field parameters in systems used for guidance, identification, gauging, and inspection. Using our specialized ACCUedge® technology, our Robotic and Machine Vision Standards are manufactured with line-edge quality that is second to none in the industry, providing the precision needed to calibrate almost any system. Should you need to alter feature patterns, size, or substrate to fit your needs, fill out our Optical Components and Standards form to start the conversation.
-
product
Meter Software Module
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Level display as five digits number*Display selectable between acceleration, velocity and displacement*RMS, positive, negative and unsigned peak values, instantaneous value *Rotary speed measurement with Photoelectric Reflex Switch (only VM-METER+)*Main frequency (only VM-METER+)*Measurement at rotation speed or multiples (only VM-METER+)*Sound level meter (A and C weighted) and noise dose meter (only VM-METER+)*THD (distortion) measurement (only VM-METER+)*One VM-METER license can be operated simultaneously up to four times with different settings*Offline measurement
-
product
Modular Mounts
M-SWITCH
The M-Switch series of adjustable, modular mounts are designed to redirect a horizontal interferometric set-up to a vertical one. This vertical orientation can help reduce distortion effects commonly found from clamping, and reduce alignment time. There are 4 primary versions of hardware designed to enable testing of mirrors, windows, lenses and lens assemblies. Holding of the part under test can be done with a variable 3 arm mount (for flexibility) or our kinematic mount (for high volume). Reference mirrors can be supplied with a variety of flatness and coating specifications to match your application needs.
-
product
HandyScope HS5: 50 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 5MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-055XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 50 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
AC Power Supply
LSP-500VAS
AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCUProtection for over hot, thundering voltage and currentTotal voltage distortion: ≤0.6%; Voltage stability: ≤0.1%/30minDownloadOutput voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400HzInput Power: single phase 220V and 50/60Hz (other input spec can be option)Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
product
Stepper Motor Drivers
Minimize noise and vibration in your stepper motor designs with our QuietStepTM adaptive stepper motor drivers. We offer a complete lineup of stepper motor drivers for office automation, industrial, and automotive applications. Our advanced QuietStepTM solutions use proprietary algorithms to reduce torque ripple and current distortion. To minimize ripple current for the various operating conditions, QuietStepTM adaptive stepper motor drivers perform on-the-fly adjustments to the amount of fast decay during a pulse-width modulation (PWM) cycle. This adaptive feature improves system performance, reduces audible motor noise and vibration, and increases step accuracy.
-
product
Embedded Local Oscillator Capability
S93084B
The S93084B tunes the network analyzer’s receivers to the output frequency of the converter under test without having to access internal LOs or a common reference signals. For converters with embedded LOs, this enables measurements of match-corrected conversion loss/gain and absolute group delay (requires S93082B and S93083B), gain compression versus frequency (requires S93086B), intermodulation distortion (requires S93087B), and noise figure (requires S93029B).
-
product
Modulation Distortion Up To 70 GHz
S930707B
S930707B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 70 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930707B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
Main Effects
The Analog Multi FX is an Authentic Analog Multi Effects Pedal equipped with everything you need to get the job done on stage and in the studio. It’s got a Switchless Optical Wah, Distortion, Effects Loop, Stereo Chorus, and Echo. Even better these are reissues of classic Morley circuits leading all the back to the 1970’s. And speaking of the 70’s it also has a new finish that pays homage to the original chrome Morley pedals. It’s Heavy-Duty spun stainless steel that’s Built like a Tank and looks great under stage lights. Each one is hand spun at our Illinois facility.
-
product
Modulation Distortion Up To 125 GHz
S930712B
S930712B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S93072B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
Distortion Test Set-Up
Model E
The Model E Distortion Tester is for testing those products that may have moderate amounts of distortion, such as pressed and formed parts of glass or plastic. It can be used for performing the distortion test required in several military specifications, such as MIL SPEC DTL-43511D.
-
product
Time-Resolved Electrochemical Quartz Crystal Microbalance
400C Series
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
product
PCIe-6738, 16-Bit, 32 Channels, 1 MS/s Analog Output Device
785822-01
The PCIe-6738 is a high-speed, high-density analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications such as stimulus-response tests, including acoustic distortion testing, and simulation such as three-phase power simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24-bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PCIe-6738 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
Function Generator
G5100A 50MHz Function / Arbitrary Waveform Generator can create stable, precise, clean and low distortion sine waves by using DDS (Direct Digital Synthesis) Technology. With fast rise and fall times up to 25 MHz for square waves and 200KHz for linear ramp waves , the G5100A also can reach users』 demand on waveforms。
-
product
ACCUplace Dot Distortion Target
AP-DD Series
All machine vision lenses will show some type of distortion. Minimizing or correcting that distortion is crucial in most applications. The ACCUplace Dot Distortion target is designed to detect the presence of both barrel/pincushion distortion as well as alignment distortion that causes the keystone effect. The precise amount of distortion is determined from an array of precisely placed dots in a regular array. The results can be used to correct for any distortion that occurs within the optical system. The AP-DD is offered on three standard substrates; Chrome on Glass (CG) Opal (OP) and Photo Paper (RM).
-
product
Intermodulation Distortion Measurements
S93087B
The S93087B intermodulation distortion (IMD) measurement makes it very easy to set-up and calibrate swept IMD measurements with a spectrum-analyzer-like display. Not available with Option 200, 210, 400 and 410.
-
product
Static Axial Clip-On Extensionmeters
The 2630 series and W-6280 series of extensometers offer speed of attachment and ease of use. The light-weight, rugged cross-brace design eliminates errors caused by physical distortion, while built-in protection ensures that damage is not caused by over-extension. The low operating-force arms of the extensometer reduce the possibility of knife-edge slippage when testing hard or smooth surfaced materials. The 2630 series extensometers can be installed or set in place accurately and consistently, with the gauge length locking device automatically releasing itself after attachment, ensuring speed and reliability of operation. This unique "cone-latch" mechanism also overcomes the problems associated with having to remove pins or clips prior to starting a test, or tests being conducted with the extensometer accidentally locked at gauge length. Because of their larger frame size, the W-6280 series extensometers require two handed operation to attach the instrument to the specimen, so these extensometers still rely on a pin to set the gauge length. All extensometers except the W-6235 allow the ability to measure both positive and negative strain allowing compressive or flexural test measurements.The 2630 series and W-6280 series extensometers include different gauge length and strain range options to suit a wide range of specimen characteristics. All 2630 series and W-6280 series extensometers comply with both the ASTM E 83 and IS0 9513 standards, and gauge lengths are available in metric or U.S. customary units. Calibration certificates are supplied, showing the individual performance of each unit at its factory calibration.Static strain measurement on a wide range of materials and specimens including metals, plastics and composites.
-
product
SparkFun THAT 1646 OutSmarts Breakout
The THAT 1646 OutSmarts Breakout Board offers an easy solution to adding a balanced audio output to your circuits. The THAT OutSmarts technology has been designed as a high-grade analog line driver and offers a low distortion and high common mode rejection in real-world audio applications. Each breakout board combines the THAT 1646 IC, its supporting components and a ¼" TRS (Tip Ring Sleeve) socket. With these powers combined, you will find it very easy to use the output drivers on breadboards and in projects!
-
product
Fuzz & Distortion Pedals
A fuzz pedal takes your sound and clips it extremely hard - known as square-wave clipping - thereby compressing the distortion to make an almost unrecognisable sound.
-
product
Renishaw Styli
Advanced Industrial Measurement Systems
Renishaw’s styli are some of the most accurate in the market. The balls on the end of the styli are bonded to the stems to ensure that there is no wiggle room – as compared to the traditional ball drilling method to fix the stem to the ball – which causes distortions, and thus measurement errors. Renishaw’s styli are a much more capable option for the CMM. These balls also perfectly spherical, are located at the optimum position on the stem, are threaded nicely and are extremely sturdy during measurement. Additionally, Revolution® CMM’s are supplied with Renishaw Grade 5 High Accuracy Styli.
-
product
Calibrating Equipment
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
product
RF Amplifier
SA812C
Hangzhou Softel Optic Co., Ltd.
SA812C1/SA812C2 Field Bidirectional AGC Amplifier is a new high gain amplifier. Adopt optimized circuit design and scientific and rational process. High performance AGC control circuit inside is useful for stable gain and low distortion. It's the best choice for large and medium-sized bidirectional CATV transmission network.
-
product
High Power AOD Driver
The Acousto-Optic Deflector (AOD) RF Driver is a three channel, three phase high power driver amplifier intended to drive devices such as the Harris H-902. The driver accepts a single low level RF input and produces three high power phase shifted outputs. The driver features adjustable gain, power monitoring, and programmable automatic protection features. The exceptional linearity and headroom allow the use of multi-tone and complex waveforms with minimal distortion.
-
product
Distortion Detector
DD-1
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment.
