Filter Results By:
Products
Applications
Manufacturers
- Optomistic Products
product
LED Test
Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.
-
product
Corrosion Analysis
Resipod
Resipod is a fully integrated 4-point Wenner probe, designed to measure the electrical resistivity of concrete in a completely non-destructive test. It is the most accurate instrument available, extremely fast and stable and packaged in a robust, waterproof housing designed to operate in a demanding site environment. The Resipod is the successor of the classic CNS Farnell Resistivity Meter.Surface resistivity measurement provides extremely useful information about the state of a concrete structure. Not only has it been proven to be directly linked to the likelihood of corrosion and the corrosion rate, recent studies have shown that there is a direct correlation between resistivity and chloride diffusion rate and even to determination of early compressive strength. This makes it one of the most versatile NDT methods for concrete.
-
product
Corrosion Test Chamber
CME SF-CCT
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
product
7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit
#8029
Innovative Products of America
Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
product
Ozone Test Chambers
Labodam Ozone Test Chambers are designed to detect the concentration of ozone while requiring low maintenance, having well-built corrosion resistant bodies, and while utilizing noiseless generators.
-
product
Sulfur Dioxide Test Machine
SQ-010
This instrument is designed according to GB/T2423.19-1981, GB/T2423.33-2005, ISO6988 (replaced DIN50018: 1988-06), DIN50900, DIN53210 and EC, MIL, ASTM etc to do sulfur dioxide gas corrosion test.
-
product
Salt Spraying Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is glad to be the ODM/OEM manufacturer of Salt Spraying Chamber,Salt Spray Test Chamber,salt spraying test chamber,Salt spraying chamber,Salt spraying chamber sales enterprises all over the world! 1：It adopts 5mm or 8mm imported gray and white impact resistant P.V.C board, with high temperature resistance up to 85℃ and corrosion resistance. 2：Support frame: ¢ 10MM fiberglass rod, corrosion resistant. The steel V-frame and the fiber rod angle are placed to ensure the specimen is inclined at 15-30 degrees. 3：Pressure barrel is welded seamlessly with 2.0MMSUS304 stainless steel plate 4：The heating adopts titanium alloy electric heating tube. It has high corrosion resistance and long service life is 3-5 years higher than ordinary stainless steel heating tube. 5：The cover is made of 5MM imported transparent (Germany YLIS) acrylic sheet. It has fine workmanship, beautiful appearance and high transparency.
-
product
Analog Tank Test Kit
4108
The voltmeter included in the kit, the “Model IA” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers a 0 - 2VDC range with a 10MΩ input impedance and the analog display presents a color divided scale for convenient indication as to whether or not a carbon-steel structure is receiving a suitable level of cathodic protection, with respect to the accepted 0.85V (850mV) threshold value.
-
product
Servopulser Overhead Actuator Type Fatigue And Endurance Testing Machine
EHF-U Series
This is a multi-functional fatigue testing machine suitable for specimens, structures and full-sized parts. It is an overhead actuator type with a broad test space, so it is ideal for various types of environmental tests, such as those in corrosion tanks or constant temperature tanks.
-
product
Non-Contact Resistance Online Tester
Non-Contact Resistance Online Tester is our company devotes ourselves to Grounding resistance test technical research’s another new high-tech product for more than ten years. Detector adopts weather fastness material manufacture, temperature resistance, cold-resistant, corrosion prevention, fire prevention. Detector’s structure is rigorous and firm, against rain, dustproof, installation and use outdoors. Non-contact measurement, safe and reliable, Ease of installation. Grounding down lead is directly through the detector perforation, Will not affect lightning protection grounding effect and the normal operation of the facilities. Ensure high-accuracy, high stability and high reliability of long time on-line monitoring outdoors, underground mine and indoors.
-
product
Salt Spray, Salt Fog & Cyclic Corrosion Testing
We service most industry segments with harsh environment, salt fog corrosion testing.If your product is coated or painted for the marine, automotive or military industries, we are equipped to provide accredited testing within multiple chambers.We provide ASTM sample preparation for coated and painted articles to ensure that your test is performed correctly.We also provide custom configurations with varied salt concentrations and temperatures for many customers with products that are used in unique environments. Products like circuit boards, electronic devices and sensors may all have specialized testing requirements.
-
product
Composite Salt Spray Test Chamber
YWX/Q-010X
Composite Salt Spray Test Chamber stimulate the actual natural conditions to do accelerated corrosion test, all the testing are based on common states on the natural environmental: such as combine with salt spray, hot air drying, humidity, low temperature and so on. The test samples are widely used on the intense changes in the environment, like automobile parts, aviation equipment, building materials, coating, electric and electrical machinery so on. YWX/Q-150X series is full compliance with ASTM D4728I, EC 60068-2-1, IEC 60068-2-14 and EIA/JEDEC JESD22-110-B standard requirements etc.
-
product
Environmental Testing Equipment
It is to do adaptability and properties test for materials under different environment conditions, which includes salt spray test to determine corrosion resistance and temperature and humidity chamber to do a variety of high-low temperature alternating test.
-
product
TDS/Conductivity And PH Testing Instruments
DS & pDS Meters™
No water supply is completely pure. Every industrial, commercial, or natural source contains dissolved solids or salts. These impurities contribute to scale, corrosion, poor taste, and environmental pollution that endanger animal and plant life. Myron L® Company has two proven ways to measure such impurities. Our DS Meters™ provide fast, accurate, on-the-spot measurements of total dissolved solids (TDS) or conductivity. pDS Meters™ test conductivity or TDS, plus pH. Readings from their highly stable circuitry help assure product quality, prevent equipment damage and verify in-line instrumentation in a wide range of applications.
-
product
Cells and Electrodes
Electrochemical cells are designed to their special purpose. The method, the matter and their reactions as well as the environmental conditions define the limitations and demands for electrochemical cells and the electrodes. Standard corrosion testing cells may have a large volume, since corrosion products shall not change the solution grossly during the test. On the other hand, it may be valuable to collect corrosion products - then a very small volume is desired ("eluation cell"). Special corrosion tests for pitting reqiure a setup where undesired crevice corrosion is excluded ("Avesta cell" , "Quarfort Cell" or "Flushed port cell". Or you want to investigate in crevice corrosion, then the cell design should meet such conditions. Have a look to the variety of cells shown here, and call us if you have a special task where a fresh design is required.
-
product
Salt Spray Test Environmental Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Salt spray chamber is used to test materials likes paints, electroplating, non-organic, pastry film, anode treatment and rust prevention oil’s corrosion resistance performance. Besides, anti-corrosion treatment of various materials to make their products resistant to corrosion.
-
product
Salt Spray Corrosion Test Chamber
CX-Y60L
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Salt Spray Corrosion Test Chamber for Nss / Acss / Cass Test is used to test the anti-erosion quality of the surface of all materials after the rust-proof of painting, coating, electroplating, anoding and rust-proof of greasing.anti corrosion treatment for a variety of materials, corrosion resistance of their products.
-
product
Field Machine
The Portable Field Machine is our most versatile full specification corrosion testing instrument. Its rugged construction and protective water resistance IP68 enclosure enables it to be operated at extreme locations throughout the world. This instrument takes laboratory precision outdoors to oil rigs, pipelines, concrete walls and just about anything that needs corrosion monitoring in situ. The potentiostat, ZRA, integral Frequency Response Analyser and Sweep Generator are exactly as provided in the laboratory Gill 8 model ensuring the most accurate testing available. The choice of tests is not limited; the AC, IR Compensation and DC tests plus the Sequencer and Analysis that are supplied with this field instrument are the same as supplied with the laboratory instruments.
-
product
Engler Viscometers
Labodam Engler Viscometers are designed according to the ASTM D1665 Test Methods for Engler Viscosity of Petroleum Products standard. It is devised with digital temperature controller and its chambers are made with stainless steel to avoid corrosion.
-
product
Salt Spray Machine
UI-E01A
Salt Spray Machine – Salt Spray Test Chamber is used to test material Corrosion resistance by producing salt fog. So it is also called salt fog test chamber. This salt spray cabinet is widely used in painting, coating and other industries. Salt Spray Test Method includes ASTM B117, B268, CNS 3627, 3885, 4159, 7669, 8886, JIS D-0201, H-8502, H-8610, K-5400, Z-2371, ISO3768, 3769, 3770, GB/T2423, GJB 150 and etc.
-
product
Salt Spray Testing/Cabinet Based Corrosion Testing
Sometimes referred to salt mist, salt fog, humidity or corrosion testingAll corrosion and environmental related tests can be tailored to customer requirementsTypical exposure times range from 16 hours to over 1000 hoursAccelerated corrosion testing can be used to check protective coatings, surface finishes and material compatibilitiesOur facilities provide a continuous controlled corrosive exposure and can combine salt spray and humidity environments.
-
product
Connector Board for Cable and Harness Tester
CB49
CAMI Research Inc. (CableEye®)
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors. There are nine preset locations for automatic detection & display of 4, 6, 8, 10, 12, 14, 16, 18, and 20-pin connectors. Yet, any single set may be fitted with any combination of lower pin count connectors that total to 20 or less (e.g. a 14-pin with a 4-pin). Connectors soldered in non-preset positions will also appear graphically correct once they are mapped with PinMap (optional software). Sold as a set of two boards, each Micro-MaTch test board may be paired with other CableEye adapter boards to accommodate any combination of connectors.
-
product
Salt Spray Test Chambers
Labodam salt spray test chambers are reliable instruments for testing the corrosion resistivity of products with painted, organic, or inorganic film surface.
-
product
Salt Spray and Fog Chamber
SS30
Bemco's Standard SS30 Salt Spray and Fog chamber meets all standard military, commercial, and ASTM salt fog corrosion and humidity corrosion tests. The SS30 is currently in redesign to incorporate a clear - see through top with the same advanced features of the previous fiberglass system. This chamber has a workspace of 48-inches wide by 36-inches high by 30-inches deep.
-
product
4/5 Pin Trailer Harness Checker / Towing Maintenance Kit
#8026
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
product
Sand Test Chambers
Labodam sand and dust test chambers are corrosion resistant equipment that tests the stability, quality, reactivity, and characterists of products against the sand and dust exposed environmental conditions. These test chambers are carefully designed as per the CE and ISO standards and provide rpotection against current leakage, overload, over-current, short circuit, over temperature, motor overheating, and over pressure for safe and precise results.
-
product
Corrosion Testing
The salt spray test is a standardized test method used to check corrosion resistance of coated samples. Coatings provide corrosion resistance to metallic parts. Since coatings can provide a high corrosion resistance through the intended life of the part in use, it is necessary to check corrosion resistance by other means. Salt spray test is an accelerated corrosion test that produces a corrosive attack to the coated samples in order to predict its suitability in use as a protective finish.
-
product
Digital Tank Test Kit
4109
The voltmeter included in the kit, the “Model DPM” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers two ranges, ±2VDC and ±20VDC with a 20MΩ input impedance. Since the voltmeter is digital [in contrast to the meter in our analog tank test kit (Cat. # 4108)], both negative and positive voltages are displayed. `
-
product
ISO Scratching Tool
1537
The Elcometer 1537 ISO Scratching Tool is a simple but effective instrument that is used to scratch the surface of samples in preparation for adhesion, salt spray and corrosion tests.
-
product
7 Spade Pin Circuit Tester / Maintenance Kit
#8028
Innovative Products of America
Test, clean and restore 7 spade pin connections.The tester will verify that the tow vehicle is sending proper signal to the connector, while accompanying cleaning tools will remove corrosion, and verify proper pin size on both male and female truck/trailer plugs. For use with 7 spade connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardPatentedKit Includes: #7893: 7 Spade Pin Circuit Tester, #8023: Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
Meter Test Switches
TESCO introduced the original Meter Test Switch in the early 1920’s. Today, TESCO’s line of Test Switches has been redesigned with the intention to combine the best features of tried and proven switching methods with improvements in materials and construction. All of the current carrying parts are bright tin plated to prevent corrosion. Good operating contact is assured on periodic meter tests, even when the switch has been idle for long periods of time in an unfavorable atmosphere.
