Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Cable Assembly, 50-Pin D-Type, Male to Male, 0.5m HV, Exit Away From Pin 1
40-970-050-0.5m-MM-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
product
NI-9870, 4-Port, RS232 C Series Serial Interface Module
779891-03
The NI‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
product
Lasers FP/DFB-LDs For OTDR
C is a 1 650 nm Multiple Quantum Well (MQW) structured Distributed Feed-Back (DFB) pulsed laser diode DIP module with single mode fiber and internal thermoelectric cooler. It is designed for light sources of Optical Time Domain Reflectometer (OTDR).
-
product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
132W to 204W - Single Output
iQE Series
*Standard Quarter Brick Footprint*18-60 Vdc, 36-75 Vdc Inputs*5, 12, 15 Vdc Outputs*1500 Vdc Isolation*-40 to 125 °C Operating Temperature*> 90% Efficiency
-
product
COM Express Type 10 Mini Module With Intel® Pentium® Processor N4200 & Celeron® Processor N3350
CEM311
The CEM311 is designed to support the Intel® Pentium® N4200 quad-core and Celeron® N3350 dual-core processors (codename: Apollo Lake). Integrated with Intel® Gen 9 graphics, the CEM311 with the support of DX12.0, OCL 2.0, OGL 4.3 delivers outstanding graphics computing, 4K resolutions and media performance. The rugged system on module supports a wide operating temperature range from -20°C to +70°C to ensure stable operation in harsh environments. The embedded platform offers onboard 4GB or 8GB of DDR3L memory and an optional eMMC flash up to 64GB. Overall, the CEM311 can be served as an excellent solution for graphics-intensive applications over the Industrial IoT, including industrial control, medical imaging, digital signage, gaming machines, military, and networking.
-
product
2.5 GHz, 0.9 pF, 1 MOhm Active Voltage Probe
ZS2500
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS2500 is ideal for 2.5 GHz and lower oscilloscopes.
-
product
Thermalert Clinical Montoring Thermometer With Analog Output
TH-5/AOP
The TH-5?AOP is one of our most economical precision thermometers in the Physitemp product line. The TH-5/AOP offers the same high accuracy (0.1°C ±1 digit) and resolution as all our other thermometers, but with a narrow temperature range. The TH-5 is ideally suited for either a laboratory or hospital setting where continuous temperature readings within the physiological range are sufficient.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 2m HV, Exit Away From Pin 1
A050DF4-T-HA200
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
4 Wire Earth Resistance & Resistivity Tester
4236 ER
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.● Optical USB to RS-232 data transmission.● The stored data can be transferred to a PC.● 2 optical LEDs are built-in for data transfer.
-
product
4 Relay Channels, Non-latching
RY1
The RY1 module features 4 individual single-pole, user SPDT Form-C (changeover/break-before-make type) relays (channels). Each channel has a common input terminal (C), a normally closed output terminal (N/C), and a normally open (N/O) output terminal. The channel either energizes or de-energizes the relays (close or open) so that the signal provided on (C) may be switched/directed to either the (N/C) or (N/O) terminals.
-
product
RTD Measurement for CompactPCI
CPCI390
The CPCI390 has a 3U form factor and features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm limit checking. Sensordata is available in °C, °F, K and Ohm. All inputs are optically isolated from the system.
-
product
Advanced 4-CH Encoder Card with High-speed Triggering Function
PCI-8124-C
PCI-8124-C is a 4-CH trigger board which is suitable for advanced line scan application which need high line rates. PCI-8124-C has internal FIFO to realize the high speed position compare and trigger pulse output. For this application, ADLINK proposes you can use PCI-8134 and PCI-8124-C together to gain the advantage of motion control and high speed trigger function. For position compare, PCI-8124-C provides two method: linear function or variable interval. PCI-8124-C also provides the variety of mapping function between comparator and trigger output. The comparator condition can be associated with latch signal, TTL input and EA/EB signal.
-
product
Optical Tester
Model C
The Model C Optical Tester is just such a device. Extremely small geometric distortion and focal length deviation can be viewed and measured easily.
-
product
*VME J2 9 slot
101VMEJ209-0900
VME J2 backplane 9 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
product
ET+UT System
Xiamen IDEA Electronic Technology Co., Ltd.
1.ET and UT detection system and testing equipments for pipe hydraulic pressure vessel 2.test: NDT Ultrasonic & eddy current3.Scan mode: A,B,C type scan4.Brand: IDEA
-
product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
product
NI-9411, ±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module
779005-01
±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module - The NI‑9411 works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and devices. The NI‑9411 is a correlated digital module, so it can perform correlated measurements, triggering, and synchronization when installed in a CompactDAQ chassis.
-
product
Current Transducer
IN 1000-S
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
product
I²C/SPI Interface Device
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
product
Data Acquisition PCI Card
UPC2100
The UPC2100 PCI Sensor Interface card provides real-world data acquisition and control for your PC. Up to 16 sensor inputs in any mix or combination are accepted by the UPC2100. No external signal conditioning is required. The UPC2100 includes configuration and data acquisition software and is compatible with C#, .NET, C++, Visual Basic, LabView.
-
product
Digital Hardness tester
THL270
Pen type Leeb hardness tester Converts to all common hardness scales (HL.HV,HB,HRC,HRB,HRA,HS). The machine also include interface to connect with impact device C, DC, G, D+15, DL
-
product
Heat Stress WBGT Meter
Heat Stress Index measures how hot it feels when humidity iscombined with temperature, air movement, and radiant heat Black Globe Temperature (TG) monitors the effectsof direct solarradiation on an exposed surface Air Temperature (TA) plus Relative Humidity (RH) Selectable units of F and C In/Out Function displays the WGBT value withor without direct sun exposure Auto Power Off with override Built-in RS-232 interface with optional Windowscompatible software Complete with two AAA batteries
-
product
Dial Durometer
Model 1600
he Model 1600 features a full-sized dial face for readability to within 1/2 point. The Model 1600 offers the maximum accuracy available in a dial model gauge at a minimum cost. Available ASTM Types: A, D, B, C, DO, E, M, O, OO, OOO, OOO-S, RR and CF
-
product
Isoperibol Calorimeter
AC500
The AC500 determines calorific value, a key indicator of quality and value in solid and liquid fuels, through measurement of the heat released after combustion of a sample. This stand-alone benchtop unit uses a fully-integrated circulation system for a compact footprint—no additional heaters or coolers required. An integral water-measuring station simplifies sample preparation, and a Windows®-based operating system uses an electronic thermometer accurate to 0.0001°C to measure temperature every six seconds. Two-channel correction is possible through constant temperature monitoring in both the outer jacket and the calorimeter proper.
-
product
Data Logger Centesimal Thermometer
HD2127.2
Centesimal thermometer in the range ±199.99°C, decimal outside this range, 2 inputs for Pt100 probes with SICRAM module.
-
product
Coaxlink Duo PCIe/104-EMB
Ruggedized board for industrial and transportation embedded applicationsSmall stackable PCIe/104 form factorExtended temperature range: -40 to +85°C / -40 to +185°FSustained shock: 40 g/11ms (all axes - half-sine and saw tooth)Optional conformal coatingTwo CoaXPress CXP-6 connections: 1,250 MB/s camera bandwidthPCIe 2.0 (Gen 2) x4 bus: 1,700 MB/s delivery bandwidth
-
product
On-line TOC Analyzer
T1 - TOCADERO Series
- Highest analytical precision with short measuring time- Catalyst-free high-temperature process at 1200°C with "Fast Change Technology- Most modern hardware components andindustry 4.0 features- Minimal material requirements and support costs- Highest processing quality- "Made in Germany"- Global service and support- Convincing cost of ownership
