Filter Results By:
Products
Applications
Manufacturers
- Taylor Dynamometer, Inc.
product
550 HP Water Brake Chassis Dynamometer
TD-36S
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 6,600 lb (2,994 kg)Capacity: 550 hp at 45 mph (410 kW at 72 kph)Rolls: 36 by 31 in. (914 by 787 mm)Pit Required Depth: 35 in. (889 mm)
-
product
Eddy Current Engine Dynamometers
A precise, low-maintenance, rapid response and repeatable alternative to water brake technology, Taylor’s Eddy Current Engine Dynos provide low-inertia, air- or water-cooled operation for testing engines up to 966 hp (720 kW) in a range of markets.
-
product
Connect Series Brake Testing Product Family
Maschinenbau Haldenwang GmbH & Co. KG.
MAHA Connect Series Brake Testing Product Family
-
product
Universal Compression Tester for Gasoline Engines
34000
Test compression on all domestic and foreign cars and most trucks. Adapters fit vehicles with 14mm and 18mm plugs including long reach and 5/8" hex plugs. Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold. Screw in adapters guarantee accuracy over push-in type testers. Quick side release valve permits retest without removal of adapters. Gage ranges 0-300 PSI and 0-21 BAR. Supplied in storage pouch.
-
product
Test bench for Diagnostics of Brake Valipers
MS300
Diagnostic equipment MS300 for repair and diagnostics of brake calipers. MS300 is manufactured fromanti-corrosion materials resistant to chemical effects of the brake fluid. The tabletop and the control panel are made of stainless steel, itensuresa long-lasting service of the equipment. A pressure indicator andhigh-pressure pumpcontrol elements are located on the control panel. There is also aconnection coupling fortested units. There is a gutter along the tabletops perimeter preventing the brake fluid from draining on the floor. For convenient use of tools, there is a section with perforation on the back side.
-
product
RV Protocol Trailer Light and Electric Brake System Tester
RVCHECK
The RVCHECK is a fast, easy, low-cost way to test RV lighting and electric braking systems. In addition to powering an RV trailer's lighting circuits for easy checking, your RVCHECK measures the current draw of the electric brake coils, and checks the break-away battery circuit.
-
product
Brake Fluid Boiling Point Tester With Bluetooth Printer
6513D
Peaceful Thriving Enterprise Co Ltd
This tester can measure the boil point of the brake fluid. It can obtain the wet boiling temperature of the brake fluid for technician as a reference for maintenance. It can be the reference when technician is going to change the brake fluid.The testing data print by Bluetooth printer.
-
product
Performance Dynamometer
The MD-250-HD was designed to be a performance dynamometer first, with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD can boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD with 900-hp worth of loading capacity for steady state testing.
-
product
Electronic Brake Meter
BrakeCheck
The Bowmonk BrakeCheck is a fully self-contained, portable, battery-powered brake meter that can be used by workshops, government traffic authorities, testing and inspection stations etc. to test and report on vehicle brake efficiency. The unit is MOT approved.
-
product
4-Pin Trailer Light Tester
3536C
Peaceful Thriving Enterprise Co Ltd
4-pin Small Size Trailer Light Tester & Circuit Troubleshooter for US, Plug tester into vehicles 4-pin connector and operate vehicle's turn signals, lights and brakes. When there is power present, the green light will glow.
-
product
Electric Motor Test Systems
Electric Motor Test Systems feature our highly successful water brake dynamometer which is used as an electric motor loading device.
-
product
Digital Roller Brake Tester for Cars and Vans up wot 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,200 mm
C_MBT C 3.5 W220 | VP 210152
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes.
-
product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
product
7 Flat (Spade) Pin Trailer Circuit Tester
PT7893
Easily test trailer plug circuitry on most new light trucks, SUV's and RV's. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
product
Electric Brake Force Meter With Dynamic Load Simulation And Circuit Testing
9107A
Innovative Products of America
The #9107 Electric Brake Force Meter with Dynamic Load Simulation and Circuit Testing (patents pending) is designed for use on 7-spade equipped vehicles. This new technology automatically recognizes the electronic signature of both Integrated (ITBC) and aftermarket Trailer Brake Controllers, simulates trailer load and displays real-time, brake-controller output gain and application time. It can quickly troubleshoot truck-side tow circuits, e.g., tail lights, turn signals, 12V+, reverse and ground condition and the 25 ft. cable allows for one-man, in-cab testing.
-
product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
product
Truck Chassis Dynamometer
Truck chassis kit includes: heavy-duty tube-steel frame and 30"-diameter "dually" wide-roll assembly with machined-in "traction grooves," air brakes, diamond-tread deck plate, floor anchors, wheel chocks, vehicle tie downs, eddy-current absorber and controller with overdrive, S-beam load cell, DYNOmite-Pro data-acquisition computer, inductive RPM pickup, DYNO-MAX software, electronic auto-load control, 28-channel data harness, engine-temperature thermistor, and more.
-
product
Brakes
Power off, fail safe holding brakes. When voltage is applied, the friction disk is released allowing the motor shaft to rotate. Pittman power off brakes are best suited for parking brake applications used to hold a load in position, and are ideal for creating brake motor packages for small frame servo and stepper motors.
-
product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P | VP 230046
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
product
Water Brake Engine Dynamometers
H36 Series
Low rpm. High torque. Ultra-low inertia. And yet, it comes in a compact package that uses as little of your valuable floor space as possible.
-
product
Exacting Electric Motor Testing
The Taylor Dynamometer Electric Motor Test Stand is designed to provide maximum reliability, excellent durability and flawless performance. Using our extensive line of Water Brake engine dynamometers, Taylor Dynamometer has systems available for testing electric motors from 5 to 13,000 hp (3.7 to 9,694 kW). Include an instrumentation package to achieve your testing requirements. From simple speed, torque and power display systems with manual control to completely automated testing solutions, Taylor Dynamometer has a system to meet your testing requirements.
-
product
Electronic Brake Meter for Forklift Trucks
BrakeCheck FLT
The BrakeCheck FLT is our portable brake tester designed specifically for forklift trucks.The Bowmonk BrakeCheck FLT is a fully self-contained, user-friendly, portable brake tester, which has been developed with a leading forklift truck manufacturer to take account of the slow speed and tilt of forklift truck vehicles. The instrument records the braking efficiency and percentage of braking imbalance in a matter of minutes.
-
product
Electrical Testers
Part of towing responsibly is making sure your trailer lights are working properly. Whether you have just installed a new vehicle-to-trailer wiring harness or are trying to locate the cause of an electrical problem, CURT connector testers are great for testing tail lights, turn signals, brake lights, ground connections and other electrical components on your trailer.
-
product
End-Of-The-Line Tester
Certifier 1200
Presenting a vehicle test station for electrical, brake, and ABS End-Of-The-Line testing from LITE-CHECK, the leader in economical, technician-friendly test equipment. With state of the art software and hardware automatic operations are recorded for a complete printed report of the vehicles electrical and air system. Heavy-duty test station for complete electrical, air brake, ABS, and 121 brake timing & end-of-line testing.
-
product
Super MUTT Deluxe Standard Edition
#9008-SE
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
-
product
Brake Test Systems
GIANT 9000 Series
The major test target is to detect noise and vibrations generated by the vehicles brake. Our intention was to build a dynamometer that can operate either with brakes mounted to the complete vehicle, or with just the axle module mounted to a universal adaptor system or wheel suspensions.
-
product
Trailer Light Tester
Checkmate 1200
Checkmate 1200 is a good, basic light tester for trailer light systems that can also serve double duty to power anti-lock brake systems.
-
product
Engine Dynamometers
Taylor’s engine dynamometers deliver the best overall value by driving productivity, ensuring uptime and bringing you rapid return on investment. We offer a variety of engine dynos including hydraulic (water brake), eddy current, AC, portable and small engine dynos. We even offer mobile test centers and engine dynamometer accessories. Search below to find what you’re looking for, or give us a call today.
-
product
Force Sensors, Controls & Switches
Direct caliper motor/spindle integration for Brake by Wire systemsExtra-small form factor MSG sensors that weigh less than five gramsFacilitating system-level miniaturizationAdvanced button-type sensors designed to lower costs and improve accuracy
-
product
Trailer Buddy 4/5 Pin One Man Trailer Wiring Tester
220
*Tests 4 & 5 Pin Flat connector wiring *Each signal from vehicle emits a unique tone *Loud beep can be heard over shop noise *One person makes complete test in 30 seconds! *Just apply brakes, turn signals, running lights& engage reverse *Tester also emits unique tone for any shorts in the wiring! *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
