Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
LXI High Voltage Matrix 2-Pole 100x2
60-310-102
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing. The 60-310 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
-
product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-5V-I
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
product
MVME5500 NXP® MPC7457 VME Single Board Computer
MVME5500
Customers looking for a technology refresh for their application while maintaining backward compatibility with their existing VMEbus infrastructure can upgrade to the MVME5500 series and take advantage of the enhanced performance features.
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
PMC Dual Channel MIL1553B Board
MS 1722
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
product
Dip Coating Systems
SCS Dip Coating systems, which are available in free-standing floor or tabletop models, are specifically designed for production applications that do not require large in-line systems. SCS dip coating systems can be used to apply a range of coatings, as well as photo-resists and solder masks, that are part of printed circuit board applications all with a level of precision that manufacturer's demand. Both SCS models include a host of features that make them an ideal choice for lab and production operations.
-
product
PXI I/O Board
MZ-TrigIO
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
product
VP F6x/msd, 6U VME processor board
VP F6x/msd
VP F6x/msd is a 6U VME processor board designed to extend the life for VMEbus deployments by using the tried and tested Universe-II VME bridge. It is based on a 4-core Intel® Xeon® E3-1505L v6 processor.
-
product
MVME4100 NXP® 8548E Processor VME Single Board Computer
MVME4100
The MVME4100 features the NXP 8548E processor, storage options, extensive I/O including 1 PMC site and up to 4 optional XMC sites via expansion cards. It provides a high-performance cost-effective path for currently deployed VME infrastructure.
-
product
Extreme Rugged PC/104-Plus, PCI-104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM3-BT4
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
Test Points
TestStation LX2
TestStation LX2 is Teradyne's largest pin count in-circuit test system. Configurable up to 15,360 pins, TestStation LX2 utilizes the new UltraPin II 128HD pin card for testing large, complex, and heavily-integrated printed circuit board assemblies.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Development System
FE-900
# Emulates Philips P89LPC932 Microcontrollers# Real-Time and Transparent Emulation up to 12MHz# 8K Emulation Memory# Real-Time Trace# Uses Philips Bond-Out Technology# Ceibo Windows Debugger and Keil uVision2# High-Level Support for all C/C++ Compilers and Assemblers# On-Line Assembler and Disassembler# Target Board, ISP Programmer and Power Supply Included# PLCC-28 Emulator Plug Included (TSSOP-28 Optional)
-
product
Multi Protocol Boards
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
product
RF Deluxe
ICAP/4Rx
ICAP/4Rx RF Deluxe is an extended version of ICAP/4Rx, including simulation capability for RF frequency design. This powerful system includes everything you need to design and verify all types of board, engineering system and IC-level design. Of course, ICAP/4Rx Power Deluxe includes Intusoft's time-tested "IsSpice4" analog and mixed-signal simulation kernel, featuring more enhancement than any SPICE kernel on the market for convergence, accuracy, speed and interactive capability.
-
product
DG I/O Backplane Extender Board
9286-1015
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
product
Analog Output/Arbitrary Waveform Generator PXI Card
GX1649 Series
The GX1649 is a 3U PXI digital to analog output board designed specifically for applications where multiple DC or AC analog outputs are required. The GX1649 offers 64 output channels with 16-bits of precision signal sourcing performance and can be used as a DC source or arbitrary waveform generator.
-
product
Solder Paste Wetting Tester
SP-2
SP-2 is wettability testing machine forsolder paste, parts electrode and PC board,adopted SP-Tension-Method (Temperature Profile Method).
-
product
PCI Express Card With Eight Isolated Inputs, Eight Relay Outputs, And Change Of State Detection
PCIe-IIRO-8
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
product
PXI Express Board Virtex-5 DAC Module1GHz, 14-bit DAC
SMT781
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or S XT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit, Custom Version
APCI-3501-8-2P
*"-2P" indicates custom version*8 analog output channels, 14-bit*Optical isolation 500 V*4 digital Input*4 digital output*24 V, optically isolated*Watchdog
-
product
Meter Warm-up Board
3000/3001
The Catalog 300X Universal Meter Warm-Up Board is designed to go from the shop floor to a customer location. TESCO's Warm-Up Board is made from a high quality industrial fiberglass enclosure and is light and durable. TESCO's warm-up board is the portable, effective solution to your shop, vehicle, or remote meter warm-up needs.
-
-
product
High Frequency Coaxial Analytical Probes
D-COAX offers four analytical probe models: HyPac model for package characterization, and two models, Omni and OmniJet, for board level characterization, and DP1.4mm differential, single-ended probe.
-
product
Advanced 4-CH Encoder Card with High-speed Triggering Function
PCI-8124-C
PCI-8124-C is a 4-CH trigger board which is suitable for advanced line scan application which need high line rates. PCI-8124-C has internal FIFO to realize the high speed position compare and trigger pulse output. For this application, ADLINK proposes you can use PCI-8134 and PCI-8124-C together to gain the advantage of motion control and high speed trigger function. For position compare, PCI-8124-C provides two method: linear function or variable interval. PCI-8124-C also provides the variety of mapping function between comparator and trigger output. The comparator condition can be associated with latch signal, TTL input and EA/EB signal.
-
product
GPS Clock
TK 42
A reliable and accurate GPS clock for LTE. The TK 42 is a plug-in board specifically designed for use in Long Term Evolution (LTE) cellular network base stations.The clock outputs 10MHz and 1PPS differential signals and will continue to operate in extreme temperature variations. The clock has typically 5 s of drift in a 24hr period whilst under holdover.
-
product
GENASYS High Density Matrix Switch Card, 104 X 8 X 8
GX6188 Series
The GX6188 is a 6U PXI, high density matrix, GENASYS architecture switching card. The card provides the user with the ability to connect and interface resources to multiple UUT connections. The board consists of two matrices - a 104x8 and a 8x8 matrix. The GX6188 can connect to 104 UUT switching points, eight external resources and an eight channel global bus via front panel connectors. Multiple GX6188 cards can be connected using the global bus. Like other GENASYS switch cards, the GX6188 features an integral, 3-dimensional switching architecture which provides the flexibility to connect test system resources to multiple UUT connections as well as supporting an expansion bus connection without sacrificing I/O matrix connections when building multiple switch card configurations.
-
product
Serial (RS-232/422/485) Module for Multi Protocol 4000 Boards
Serial Module for Multi Protocol 4000 BoardsNOTE: The M4KSerial module is now a Legacy product. All new projects should use the M4KSerialPlus module (these modules are not compatible)
-
product
PXI 16 x SPST Reed Relay
40-115-021
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
