Filter Results By:
Products
Applications
Manufacturers
Vertical Cavity Surface Emitting Lasers
a semiconductor laser diode with light emmission perpendicular from top surface.
- Virginia Panel Corporation
product
Vertical Hinged Mounting Frame, G6, 5U, 2 Positions
310113397
This 2-position G6 Vertical Hinged Mounting Frame is for use with standard racks or PXI chassis. These mounting frames attach to flanges supplied by the chassis manufacturer and allow the receiver to hinge down for wiring access.
-
product
Optical Modules
VI Systems GmbH introduces the fiber coupled 850nm vertical cavity surface emitting laser (VCSEL) transmitter module VM64-850M for data rates of up to 80 Gbit/s. The transmitter module features a V-connector for the electrical input signal and for the optical output a 50/125 multi mode fiber which is terminated with a standard FC/PC connector. The left picture below shows the module. The picture on the right shows an optical eye diagram at 32 Gbaud (64 Gbit/s) in a back-to-back test configuration as tested by partners at the Heinrich Hertz Institute in Berlin.
-
product
SparkFun Distance Sensor
1.3 Meter, VL53L4CD (Qwiic)
This SparkFun Distance Sensor Breakout utilizes the VL53L4CD next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at short ranges for its size. The VL53L4CD from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 1mm to 1300mm away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
product
Wet Oxidation System For VCSEL Fabrication
VIXEL-320
s a wet oxidation system intended for the fabrication of Vertical Cavity Surface Emitting Lasers. It is an atmospheric-pressure oxidation system with in-situ monitoring of oxide aperture formation. It accommodates single wafers of up to 150mm (6? in diameter.
-
product
SparkFun Distance Sensor Breakout
4 Meter, VL53L1X (Qwiic)
This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 40mm to 4m away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
product
VCSEL Light Source
ams supplies LiDAR systems with specific light sources, called VCSEL (Vertical Cavity Surface Emitting Laser). These VCSELs offer specific advantages over other types of light sources as for instance Edge Emitter Lasers:
-
product
PCI Three-Axis Laser Board
N1231A
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
Fixed Wavelength CW Laser Source (DFB)
Laser 1200 Series
The Laser 1200 Series is a highly customizable fixed-wavelength Continuous Wave (CW) laser source available in a wide range of wavelengths and powers.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
product
Optoelectronics and Photonics
SemiProbe has developed probe stations for a wide variety of optoelectronic and photonic device applications, including light emitting diodes (LEDs), vertical cavity surface emitting lasers (VCSEL) and photo diodes. Testing and handling small, fragile, thin wafers with thousands of die on them poses unique challenges that require innovative solutions.
-
product
Fixed Wavelength CW Laser Source (FP) - MATRIQ
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
product
Fixed Wavelength CW Laser Source (FP) - PXI
Laser 1100 Series
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
Tunable Laser Source - MATRIQ
The Laser 1000 Series is a fully-compliant micro-ITLA laser with up to four channels in a compact benchtop form factor.Offering 0.01 pm resolution tunability across C or L bands, exceptional power accuracy up to 16.5dBm, and optional dither suppression, this is a versatile and cost-effective general purpose instrument.
-
product
Laser Surface Velocimeter
LSV-1000
The LSV-1000 represents Polytec?s new, compact velocimeter generation for non-contact length and speed measurement of continuous goods. The sensor provides length and velocity data fast, laser-precise and reliably for control and cut-to-length applications.
-
product
External Cavity Diode Lasers
ECDLs
High-performance ECDLs and injection-locked optical amplifier.
-
-
-
product
Cavity Stabilized IMPATT Oscillators
Available Frequencies: from 26.5 to 140 GHz Maximum CW power: 300 mWatt Frequency stability: from 0.05 to 0.2 MHz/C
-
-
product
Surface Analysis
Innova-IRIS
This provides researchers a perfect combination of chemical or crystallographic information at high spatial and spectral resolution with the most advanced atomic force microscopy characterization. The Innova-IRIS can be integrated with your choice of a leading Raman system to provide the best opaque sample TERS investigations available today. However you tailor your system, your application will benefit from Bruker exclusive, high-contrast IRIS TERS probes and the best tip preservation and lowest drift, guaranteeing that alignment is preserved even over the optical integration times necessary to interrogate weak Raman scatterers.
-
product
Zero Field Cavity
Zero field cavities generate a zero magnetic field in an air gap. They are mainly used to calibrate hall probes for their zero scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using Zero Field Cavity.
-
product
Laser
Helium Neon Laser whose frequency is stabilized to saturated absorption lines of Iodine molecules.
-
product
Vertical Measuring Projector
Sinowon Innovation Metrology Manufacture Ltd.
◆ The lifting system adopts cross roller rail and precision screw drive, which makes lifting drive more comfortable and stable;◆ Coating process reflector, clearer image and great dustproof;◆ Adjustable contour and surface illumination, to meet with difference workpiece demand;◆ Imported high light and long using life LED illumination ,to ensure precision measurement demand;◆ High resolution optical system with clear image and magnification error is less than 0.08%;◆ Powerful Bi-axial fan cooling system，highly increase using life;◆ Powerful and colorful DRO DP400，realized fast and accurate 2D Measurement;◆ Built-in Mini-printer, can print and save data;◆ With standard 10X objective, optional 5X,20X，50X，100X objective，rotary table, foot switch ,clamp, etc.
-
product
6U Vertical Card
440
VECTOR Electronics and Technology, Inc.
Chassis for vertical card installation
-
product
Surface Analysis
Bruker Nano Surfaces provides industry-leading surface analysis instruments for the research and production environment. Our broad range of 2D and 3D surface profiler solutions supply the specific information needed to answer R&D, QA/QC, and surface measurement questions with speed, accuracy, and ease. Bruker’s AFMs are enabling scientists around the world to make discoveries and advance their understanding of materials and biological systems. Our tribometers and mechanical testers deliver practical data used to help improve development of materials and tribological systems.
-
product
Surface Comparators & Magnifier
127
Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made.
-
product
Surface Thermometers
Tel-Tru® Manufacturing Company
Tel-Tru Surface Thermometers are designed to measure surface temperatures on a wide variety of surfaces and are available in several configurations.
-
product
Surface Profilers
Taylor Hobson offers a world leading range surface form, surface finish and metrology solutions for 3D contour,ideal for the most demanding applications.
-
product
Laser Levels
Use a laser, an amplified, focused beam of light emitted from a solid-state device called a diode.
-
product
Laser Interferometers
Measurements of the length displacement or yawing and pitching, measurements of rotation angles, measurements of overshoots during vibrations or when stopped and of uneven speed, etc. can be handled. Length measuring instruments can be used for a variety of purposes, including precise inspection of heavy duty equipment.
-
product
Lasers And LEDs
AGILE features a broadband spectral output from <400 nm to >2000 nm and pulse repetition rates from 10 kHz to 1 MHz, making it the ideal light source for the majority of fluorescence lifetime applications. Using the Time-Correlated Single Photon Counting (TCSPC) technique, fluorescence lifetimes from a few picoseconds to microseconds can be accurately resolved. It is also compatible with Multi-Channel Scaling (MCS) mode for lifetimes up to 10 μs.
