Filter Results By:
Products
Applications
Manufacturers
Pulse Amplifiers
increase amplitude while keeping waveform. AKA: Pulsed Amplifiers
- Pickering Interfaces Inc.
product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
product
CZT Gamma-Ray Detector Spectrometer
GR Family
The Kromek GR family is a range of CZT-based high-performance gamma-ray spectrometers. They are completely self-contained, with built-in preamplifier, shaping amplifier, baseline restorer, pulse height digitizer, and HV supply. The digitized pulse heights of detected gamma-ray signals are sent to a PC via the USB. The unit is powered entirely from the USB bus, so no external power supply is needed.
-
product
DC-Coupled Pulse Amplifiers
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
product
Non-Programmable Signal Conditioning
7525
The Dynamics 7525 Differential Amplifier was designed for use in high-speed data systems. It is completely compatible with all tape recorders for direct recording and is also useful for isolating digital or high-speed impulse signals when you cannot afford to reconstruct the signal or change pulse characteristics.
-
product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
product
Pulsed And CW ESR/EPR And DNP: Synthesizer Up To 140 GHz With Output Power Up To 30 Watt
Insight Product Company offers a high-power synthesizer of pulsed signals. They are ideal for ESR, EPR, and DNP experiments. The synthesizer has a high frequency stability (10-6), and allows control over the duraction and begining time of pulses. The synthesizer also enables phase manipulation, where each pulse is shifted by 90 or 180 degrees relative to the previous pulse. In contrast with the PIN modulators and injection-locked power amplifiers this synthesizer has absolutely no residual signal in the "OFF" position.
-
product
Power Sensors
RTP5540
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 40 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Pulsed ESR/EPR: Pulsed Injection-locked IMPATT Amplifiers
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
product
Gated Integrator | Boxcar Averager
GIA100
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
product
Pulsed Injection-Locked IMPATT Amplifiers
Pulsed ESR/EPR
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
product
RF Amplifiers up to 2500 MHz
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
product
Dual Channel High-Voltage Amplifier
2350
The Model 2340/2350 High Voltage Amplifier expands the amplitude range of any standard, 50 function, pulse, or waveform generator to 400 volts p-p. Model 2340/2350 comes standard with a fixed gain of +50, and gains from 10 to 100 are available as special order.
-
product
Pulsed Fiber Amplifier
MOPA
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
product
CEP Stable Lasers And CEP Phase Stabilization
Carrier envelope phase stabilization (CEP) is an enabling technology for metrology and for the generation of few cycle pulses. As one of the pioneers in the field we have developed products that allow to stabilize the carrier envelope phase of light pulses of few cycle pulse oscillators and amplifiers.
-
product
Power Sensors
RTP5518
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 18 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
product
Centralized Motion Controllers
Pulse train motion controllers generate high-frequency digital signals to control servo motors and steppers, matching performance and precision positioning of high-performance servo amplifiers.
-
product
Optical Parametric Amplifier
AVUS is an Optical Parametric Amplifier (OPA) that provides widely tunable high energy pulses and high repetition rates (up to 1 MHz). AVUS offers highest average output power on the market and is designed for 1 µm fs pump lasers.
-
product
PNA-X Network Analyzers
Keysight's PNA-X is more than just a vector network analyzer. It is the world’s most integrated and flexible microwave test engine for measuring amplifiers, mixers, frequency converters, and other active devices. The hardware includes two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points. These hardware features provide a powerful core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device under test.
-
product
6-Channel VME Pulse Amplifier
V860
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
product
Photodetectors
Detection of weak light pulses on the few-photon level is crucial for many applications. The Menlo Systems' detector portfolio includes PIN photodiodes with low noise RF amplifiers, ultrafast avalanche photodetectors with integrated high voltage supplies, and detectors based on homo- and heterodyne detection.
-
product
Power Sensors
RTP5006
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 6 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements.This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Compact Fiber Seeders
LightWire FPS Series
LightWire FPS series fiber lasers are dedicated for seeding solid state Nd:YAG amplifiers. Compact, cost efficient FPS series models deliver sub‑10 ps pulses at 1064 nm wavelength with the average output power up to 200 mW and pulse energy up to 50 nJ.
-
product
MICROWAVE POWER MODULES
Ultra-compact “drop-in” microwave amplifier blocks; Pulsed or CW operationExternal TWT connections are eliminatedSafe and easy installationHigh reliabilityExcellent thermal managementS to Ka band frequency rangeParticularly suitable for airborne applications or where space and weight are criticalTWT based and solid state versions availableITAR free versions available
-
product
YDFA Amplifier
a high-gain three staged polarization maintaining optical amplifier unit designed for applications requiring high efficiency optical amplification in the 1060 nm regime in both CW and pulse mode operations.
-
product
Frequency & Pulse Distribution
Timetech frequency distribution amplifiers and pulse distribution units.
-
product
RF Front-End ICs
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
product
Double Taper Horn Antenna
MDTH series
This product is the antenna that corresponds to the radar pulse immunity test for automotive equipments. Automotive manufacturers have required the electric field strength of 600 v/m. Amplifier system and cable will be cheaper, and will contribute to the ecology.
-
product
Broadband Power Amplifier
Panda Microwave design, manufacture, and support a wide variety of Power Amplifier. RF amplifiers product line from Panda Microwave consists of low noise amplifiers, Power Amplifier Module and Solid State High Power Amplifier. Our Power amplifiers cover frequency range from 100MHz to 50GHz and used Thin-film Technology. Our low noise amplifiers have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifiers system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
product
Clock Drivers
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
product
Field Strength Meter
FIM-72A UHF
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
