Filter Results By:
Products
Applications
Manufacturers
Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
- Pickering Interfaces Inc.
product
PXI 4 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-021-184X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXIe-4339, 25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
783531-01
25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4339 is a universal bridge input module ideal for test cell installations requiring both accuracy and flexibility. Completely configurable through software, each channel can take bridge-based measurements and direct voltage measurements. Eight input ranges in ratiometric mode and four in voltage mode accommodate a wide variety of sensor types for your changing application needs. The PXIe‑4339 also features per-channel wide bandwidth analog outputs, programmable excitation, Transducer Electronic Data Sheet (TEDS) support, and digital filtering.
-
product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit, Custom Version
APCI-3501-8-2P
*"-2P" indicates custom version*8 analog output channels, 14-bit*Optical isolation 500 V*4 digital Input*4 digital output*24 V, optically isolated*Watchdog
-
product
Serial Analog Interface
Model 2361B
* Model 2361B-24 Provides four isolated analog outputs with programmable ranges.* Provides four isolated high-current drive signals and 8 digital inputs. * Includes 4 floating analog inputs.* 1 U high rack mount kit mounts one or two 2361Bs.* Includes US 115 VAC Power Adapter* Compatible with our earlier 2361 and 2361As.
-
product
Advanced Test Platform
980 12G
The Teledyne LeCroy quantumdata 980 12G-SDI Video Generator / Analyzer module supports video and audio functional testing of next gen broadcast monitors, conversion devices and sources up to 12G-SDI. The module is equipped with four (4)12G-SDI-capable output ports. The output ports can be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. A genlock input supporting both SD analog black burst and HD tri-level to sync the output clocks with a "house sync" but the module can also run off its internal clock. The module's four (4) SDI input ports can also be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. For single link operation only port 1 on the input or output is functional.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Multi-Function DAQ
Full spectrum of DAQ cards provides analog input and output, digital input and output, and counter/timer circuitry.
-
product
RTM Actuator Signal Conditioning Board
MS 3630I
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
Test Pattern Generator Delay & AV Sync Analyzer
VQDM-100
Versatile compact and robust multi-purpose tool for R&D and glass-to-glass QA/QC Instant visual-aural quality estimation plus automatic latency, AV sync and 3D LR sync measurement Multi-channel time-line analysis, including video frames continuity testing 4 Light Sensors with vacuum caps, 4 Audio inputs (standard line levels) 2 channels of AV timing analysis, simultaneous measurements of Video and Audio Latencies Real time multi-channel data acquisition via USB port Unique sophisticated set of static and dynamic test patterns up to 1080p@60fps - see more details in separate VQL page Source of VQDM, VQMA2, and VQMA3 Test Patterns for VideoQ Analyzers Multi-format digital and analog AV outputs: HDMI, YPrPb, S-video, SPDIF, LR analog audio Networkable unit, easy expansion with any external USB storage device: live clips, user content, etc.
-
product
10 Channel ADC FMC Module
ADCFN10-AC – HPC
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
product
USB I/O Module for Sound and Vibration
JSV-4431-USB
4-channel ICP analog voltage input 102.4KS/s maximumsample rate, simultaneous acquisition Analog-to-digital converter：delta-sigma, 24 bits Phase Accuracy < 0.05deg@10KHz Optional Input voltage range: ±10 V,±5V, ±1Vm ±100mV ； Signal conditioning: anti-aliasing filter Digital filter: user-defined low pass, high pass, band pass, band stop Dynamic range: 100 dB ICP current: 0-4 mA, optional 1-channel analog output voltage：±3.5 V; update rate: 96 kS/s Overload indication: software display
-
product
16-Bit Multi-Function CPCI Card With A/D, D/A And Digital I/O Channels
GX3216 Series
The GX3216 is a multi-channel analog input and output cPCI module, supporting 16 differential input channels and two analog output channels. Dedicated 1 MS/s D to As and A to Ds allow simultaneous acquisition and generation of analog signals. Input ranges are software-selectable as ±10 V, ±5 V or ±2.5 V. The inputs are divided into two channel groups, with an independent software-controlled range assignable to each group. Two analog output channels provide software-selected output ranges of ±2.5 V, ±5 V or ±10 V and independent of the input range assignments. Output data is provided via two dedicated control registers, or through a 256 K-Sample FIFO buffer for waveform generation. Six bidirectional digital I/O lines are also available and can be programmed as inputs or outputs.
-
product
Monitoring Relays
A Monitoring Relay is a protective control device. The basic functions are to receive input signals, monitor and determine them, and output an alarm signal if a set value (threshold) is reached. Monitoring Relays monitor power supplies (voltage, current, power, phase), temperatures, and other analog signals and detects abnormalities in machines and equipment by determining values against alarm thresholds.
-
product
Portable Paperless Recorder
5.7” Colour TFT LCD (320 x 240) with Backlight8 Input Temperature Measurement / Logging (ºC/ºF )Colour Graphic Display of 8 Curves at the same timeDigital & Analog (bargraph) Data DisplaySelection of 11 Types of Thermocouple (K, J, E, T, R, S, N,..)Easy Socket for Thermocouple Mini ConnectorBasic Accuracy 0.05 % ± 1ºC (K Type)28 Hours Recording with Lithium Battery of 3400 mAHStatistics Data (Histogram) for easy AnalysisProgrammable Hi-Lo Alarm with TimerDisplay of Max & Min Values for each InputSampling Rate 8 Inputs / 1 SecondHide or Display Selected CurvesStandard 2G SD Memory Card (Stores 3.8 Year of Data)SD Card Directly Read by PCRead & Delete Data files DirectlyBuilt-in Calendar ClockAccept Analog Outputs from InstrumentsScreen Hardcopy for Easy Documentation Ready to Use Package ( Thermocouples, SD Card & Battery)
-
product
Universal Control Unit For CAN Applications
PCAN MIO
The multiple input output module (MIO) is a universal, modular control unit for use in the industrial and automotive sectors. The module has two CAN interfaces and several analog and digital inputs and outputs. Incoming signals can be processed via the microcontroller and then output via the CAN interfaces or output channels. The behavior of the PCAN-MIO module is freely configured with comprehensive Windows software. A large number of function blocks and other settings are available to the user for creating such a configuration.
-
product
Test Receiver
FSWT
The R&S®FSWT is the right tool for detecting compromising emanations. With two equivalent, switchable RF inputs, up to 500 MHz measurement and analysis bandwidth and two analog outputs for video voltage and demodulators, the R&S®FSWT fits perfectly into typical test setups and easily replaces older instruments.
-
product
PCI-6115, 4 AI (12-Bit, 10 MS/s/ch, Buffer Rate 32MS), 2 AO, 8 DIO, PCI Multifunction I/O Device
778554-01
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6115 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6115 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6115 dimensions require chassis slots that can accommodate full-length PCI modules.
-
product
Power Supply, 80 V, 65 A, 5,200 W
N8758A
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8758A is an 80 V, 65 A, 5,200 W, single-output power supply in a small 2U package. It offers flexible AC input options, analog / resistance control of output voltage and current, and parallel and series connection of multiple supplies to achieve more output current or voltage.
-
product
USB-6212, 16 AI (16-Bit, 400 kS/s), 2 AO (250 kS/s), Up to 32 DIO USB Multifunction I/O Device
780107-01
16 AI (16-Bit, 400 kS/s), 2 AO (250 kS/s), Up to 32 DIO USB Multifunction I/O Device - The USB‑6212 is a multifunction DAQ device. It offers analog input, digital input, digital output, and two 32‑bit counters. The device provides an onboard amplifier designed for fast settling times at high scanning rates. It also features signal streaming technology that gives you DMA-like bidirectional high-speed streaming of data across USB. The device is ideal for test, control, and design applications including portable data logging, field monitoring, embedded OEM, in-vehicle data acquisition, and academic. The USB‑6212 features a lightweight mechanical enclosure and is bus powered for easy portability. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
RTM Sensor Signal Conditioning Board
MS 3631I
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
product
Party Line Intercom Conversion
COMMS Series
The stand-alone COMMS 300 and the OG-COMMS openGear® units provide a means to interface between two channels of 2-wire party-line intercom audio and two channels of 4-Wire analog line-level signals. The unit is capable of performing auto nulling for each channel with the push of a button. In addition, each of the 4-Wire input and output channel levels are monitored and displayed on easy to understand front panel VU meters.
-
product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
product
VME Analog Output Module
DP-VME-2115
DP-VME-2115 is an industrial standard 24 channel D/A (Digital to Analog) board. It incorporates most of the features which are demanded in industrial applications. Each Digital to Analog Converter (DAC) is provided with a separate reference voltage selection either from internally generated reference or from the external input. This external input reference signal is passed into the protection circuits before it is fed to any active components. The input protection circuit is designed for ± 25Vp-p input ranges. The DAC output may be unipolar or bipolar and the output is jumper selectable, which is routed to the VME P2 connector, with short circuit protection of upto 30mA.
-
product
Low Cost Splitter Systems
RATCAT Family
The CAT Snake Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5/6/7 cable. Each of its four channels can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds of feet away. The CAT Snake is a fully passive unit which can be input directly into analog or digital consoles. Each channel is isolated which means channel 1 can send a DMX Signal while channel 2 is sending balanced analog all down the same shielded CAT5 cable. Multiple CAT Snake stage boxes can be daisy chained to allow the same four analog channels to be dropped in multiple locations. Each CAT Snake stage box has an Ethercon input and Ethercon parallel output that allows the CAT Snake to be used as a hard-wire split.
-
product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
Radiation Microdosimeters
Teledyne e2v HiRel Microdosimeter is a compact hybrid microcircuit which directly measures total ionizing dose (TID) absorbed by an internal silicon test mass. The test mass simulates silicon die of integrated circuits on-board a host spacecraft in critical mission payloads and subsystems. By accurately measuring the energy absorbed from electrons, protons, and gamma rays, an estimate of the dose absorbed by other electronic devices on the same vehicle can be made. The Microdosimeter can operate from a wide range of input voltages. The accumulated dose is presented to three dc linear outputs and one pseudo-logarithmic output giving a dose resolution of 14 µrads and a measurement range up to 40 krads. These outputs are intended to be directly connected to most analog-to-digital converters (ADCs) or spacecraft housekeeping analog inputs (0-5 V range), which makes minimal demands on the host vehicle. The Microdosimeter incorporates a test function to allow electrical testing of the hybrid without the need for a radiation source.
-
product
PMAC Input/Output (IO) Modules
PMAC Input/ output (I/O) modules offer a wide range of analog or digital IO including AC, DC, TTL and analog.
-
product
Modbus Analog Output Modules
DAT3020 Series
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
product
32x ADC, 16x/0x DAC & 8x Digital I/O PMC Module
TPMC533
The TPMC533 is a standard single-wide PCI Mezzanine Card (PMC) compatible module providing 32 channels of simultaneous sampling true differential bipolar 16bit analog input, 16 or no channels of simultaneous update single-ended unipolar/bipolar 16bit analog output and 8 channels of tri-state 5V-tolerant TTL digital input/output. All signals are accessible through a HDRA100 type front I/O connector.
