Filter Results By:
Products
Applications
Manufacturers
- Applied Instruments, Inc.
product
Portable RF Signal Generator
ACE 5400
The ACE 5400 portable RF signal generator has four carriers that can be activated individually or in any combination. Each frequency and amplitude is adjustable by the user. The ACE 5400's basic and straight forward performance is perfect for applications that require a precise, stable RF stimulus. Applications: Testing and aligning CATV return bands; Great for institutional networks.
-
product
COTS VME Board Tester
*Developed for support of Virginia Class Submarine at the COATS Integration Facility.*Provides Stimulus and Measurement Subsystem (SMS) to control, monitor, and evaluate VME assets used in the Non-Propulsion Electronic System (NPES) of the submarine.*Provides Native Environment Subsystem (NES) that simulates the operational configuration of typical NPES installations, and permits the test and evaluation of several types of VME assets.
-
product
Fault Diagnostics in Power-Off State
QT55
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
360 EC-RTL
During a typical development process, there are many occasions where a change needs to be made to a block, which must then be retested to ensure functional equivalence. For example, once a block has been proven to operate correctly, a designer may wish to optimize some section, maybe to improve the coding style, reduce the gate count or streamline operation. Today, an engineer must execute an entire simulation regression run to verify each change. This often requires a lot of time and may also need additional stimulus, with no guarantee that an exhaustive functional check will be performed.
-
product
Modulation Distortion Up To 53 GHz
S95070B
S95070B software enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 53 GHz. The wide dynamic range and vector error correction of the PXI VNA results in an extremely low residual EVM from the test setup, giving you a complete picture of your device’s performance without test system interference. S95070B software measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals through spectral correlation between the input and output spectrum, without doing demodulation. Integration with the PXI VNA’s measurement flexibility enables you to do quick modulation distortion measurements along with traditional VNA tests.
-
product
RF Automated Accelerated Reliability Test Station (AARTS)
RF-HTOL
The RF Automated Accelerated Reliability Test Station (AARTS) systems are designed to stress devices with RF, DC, and thermal stimulus. The systems were designed from their inception to include RF stimulus - it was not added as an after-thought. Hence, the software and hardware are fully integrated and provide full-featured support.
-
product
Detector Test Bench
RTB 3000
The RTB 3000 Detector Test Bench from Santa Barbara Infrared (SBIR) is a flexible integrated IR detector test station for evaluation of single element detectors, linear arrays, and focal plane arrays. The RTB 3000 provides the radiometric stimulus necessary to perform accurate IR detector testing in both laboratory and production environments.
-
product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
product
Pulse Generators
Keysight Technologies offers the most comprehensive portfolio of stimulus solutions for the generation of digital and analog waveforms and data signals. The Keysight instruments cover a frequency range from 1 μHz to 56 Gb/s and an output amplitude range from 50 mV to 20V.
-
product
Measurement and Analytics Solutions
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
product
Modulation Distortion Up To 70 GHz
S930707B
S930707B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 70 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930707B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
6U CPCI D/S, S/D, I/O & Comm Board
78CS2
NAI’s 78CS2 is a 6U cPCI Multifunction I/O and Communication Board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five independent function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Modulation Distortion Up To 125 GHz
S930712B
S930712B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S93072B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
VXI Precision Waveform Synthesizer
3151B
The Racal Instruments™ 3151B Waveform Synthesizer combines 250 MS/s waveform generation performance, versatility, and compact size into a singleslot VXIbus format. The 3151B is a greatly improved version of a field-proveninstrument ideal for VXI test stimulus generation. It replaces the 3151A+ and other similar units which were standard on many military and commercial test platforms.
-
product
JTAG Boundary-Scan I/O Modules
SCANIO Family
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
product
Carbon Monoxide Detector Tester
Solo C3
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
product
MEMS Handler
4664-IH
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
product
6U VME D/S, S/D, I/O & Comm Board
64CS4
NAI’s 64CS4 is a 6U VME multifunction I/O board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five intelligent, function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Modular Power
RFP Controller
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
Accessories: Test Hardware
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
product
Resolver to Digital and Digital to Resolver Converter
DP-VME-5031
DP-VME-5031 is a Resolver to Digital and Digital to Resolver Converter module. This module has four resolver to digital converters as measurement channels and six digital to resolver converters as stimulus channels.
-
product
Protocol Analyzer and Exerciser
Keysight's protocol test solutions for each technology typically consists of both protocol analyzer application as well as a stimulus solution, such as an exerciser or traffic generator. Keysight's protocol test solutions combine multi-protocol analysis, traffic generation, performance and conformance verification to debug, validate and optimize your designs using high speed protocol standards.
-
product
PCI D/S, S/D, I/O & Comm Board
76CS3
NAI’s 76CS3 is a PCI/PCIe multifunction I/O and communication board designed for applications requiring Digital-to-Synchro/Resolver (D/S) and Digital-to-LVDT/RVDT (DLV) stimulus output, as well as I/O and communication functions. This full-slot board contains five independent, function module slots. The board can be configured for 6 separate D/S channels, or for D/S in combination with I/O and communication modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Thermal Sensitivity Tester
NTE-2A
The NTE-2A Thermal Probe is a sophisticated, non-invasive device for the clinical evaluation of neuropathy and the assessment of short fiber neurological function. Individual thresholds are compared to normals to statistical normals. These results provide an accurate means of tracking chronic changes in small fiber nerve function. It can be used for pain studies and in any application were a variable, accurately-controlled temperature stimulus is required. The NTE-2A is often used in conjunction with the Vibratron II to assess peripheral neuropathies.
-
product
Benchtop Wiring Analyzer
2115
The Model 2115's compact size makes it the ideal choice for many benchtop or portable test applications. The small size does not mean you sacrifice any functionality. The 2115 delivers a full 1500 volt isolation and 2 amp continuity test stimulus. With the optional AC breakdown test providing 1000 VAC test stimulus, you will meet all test requirements.
-
product
Power-Switching Test System
High Voltage Switching Test System
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
product
CXA-m PXIe Signal Analyzer
M9290A
Deploy a smaller microwave footprint, no trade-off in precision: Rely on fully specified performance up to 26.5 GHz in 4 slots Optimize your balance between speed, sensitivity and accuracy with the choice to operate in swept or FFT modes Perform fast calibrated stimulus response measurement with full-band tracking generator Smooth the transition between R&D, manufacturing, and maintenance: CXA-m is code compatible with benchtop X-Series signal analyzers and ESA spectrum analyzers
-
product
High Speed Digital Analog
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
product
True-Mode Stimulus
S95460B
S95460B provides mismatch-corrected true-mode stimulus and enables accurate balanced measurements on M980xA PXI vector network analyzers.
