Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
37-Pin D-Type Male Solder Pin HV
92-960-037-M-HV
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
Socket Phone
Design for phone device test and system verify.Phone device: CPU,flash,baseband,LPDDR,power IC.etcPitch range from 0.30 to 1.27mmKey material: PEI,Peek,Torlon,PPS.etcContact with top pogo pin
-
product
Wafer Probe Loadboards/PIB
DTS has a full line of standard PIBs for all major tester platforms. Custom PIB designs can accommodate any test head, prober and manipulator configuration, including probe card changers, overhead direct dock setups and cable interfaces. DTS wafer test loadboards are compatible with a variety of pogo pin interface towers. All PIBs are constructed with impedance control, precision matched line lengths, full power and ground planes and both analog and digital resources to provide high quality signal integrity directly to the device.
-
product
Test Probes and Pins
Spring Loaded Test Probes for Circuit Board Testing, "Pogo Pins" Test Electronics sources and stockes a large variety of Test Probes and Spring Loaded Test Pins. Let our applications engineers help you find the correct pin for your test fixture application.
-
product
Micro Pogo Pin Tips for ZD Differential Probe Qty 6
PACC-ZD009
Micro pogo pin tips for ZD differential probeQty 6
-
product
Custom Pogo Pin Rings & Blocks
Reduce your cost-of-test with our pogo pin blocks and interfaces that transform complex DUT boards or breakout boards into universal motherboard-style interfaces. Eliminate the need to purchase or build a new board for every unique device, unit, or package.
-
product
Module Fixture
Design according to customer's requirementsUse on auto or semi-auto test eqiupments and handler.Pitch range from 0.30mm and above.Pin amount: 2 and above.Key material: Peek,Torlon,PPS,PEI.etcContact with top pogo pin
-
product
ATE Socket
Design ATE socket according to customer's requirementsUse on auto-test eqiupments and handler.Pitch range from 0.30 to 1.0mm.Pin amount: 2 and above.Key material: Peek,Torlon.etcContact with top pogo pin
-
product
Pogo Pin
Probe pin is also known as pogo pin or spring probe. It is designed to test the connection between two circuit boards and devices or equipment under test.
-
product
Screw Pins
C.C.P. Contact Probes Co., LTD.
CCP's Screw Pin is an extremely smart way to utilize a pogo pin as a connector as well as a mounting part.
-
-
-
-
product
100 Pin 1.27mm Pitch Micro-D Cables - 100 Pin To 100 Pin For Pickering Products
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 100-pin Micro-D connector.
-
product
Pin Electronics (PE)/ Pin Drivers ATE
Analog Devices integrated pin electronics (PE) support speeds up to 2.5Gbps at high accuracy and low power, all manufactured on ADI's proprietary fab processes, providing unmatched test solutions needed for cost-sensitive, test applications.
-
product
6 Pin Round Pin Tester / Maintenance Kit
#8027
Innovative Products of America
Test, clean and restore 6 round pin trailer connections. Included tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 6 round connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsPatentedKit Includes: #7897: 6 Pin Round Pin Tester, #8022: 6 Round Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
200 Pin LFH Cables - 200 Pin to 200 Pin for Pickering Products
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin LFH connector.
-
product
37 Pin Breakout Interface
VSI-Breakout-37
The VSI-Breakout-37 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
-
product
500 Pin SEARAY Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
PIN Diodes
PIN photodiodes convert light to current – without a bias voltage having to be applied. Silicon is commonly used as an inexpensive detector material in the Vis range. For higher demands, InGaAs is used; it covers the widest spectral range from the Vis to the NIR. We offer silicon carbide as a “solar-blind” detector specifically for the UV range.
-
product
200 Pin LFH Cables - 200 Pin to 200-Pin
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
20 Pin GMCT Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
compactPCI Bus Pin Assignment
VECTOR Electronics and Technology, Inc.
cPCI Bus pin assignments per PICMG 2.0 R3.0
-
-
product
200 Pin LFH Cables - 200 Pin to 200 Pin for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin LFH connector.
-
product
8 Pin Power D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
IEC61032 Test Probe Pin
CX-112
Shenzhen Chuangxin Instruments Co., Ltd.
1. Jointed test finger probe (Figure 2 / Test Probe B / IEC 61032)This is a precision probe made in accordance with all IEC standards. Examples are IEC 61032, 60950, 61010 and 60601; and it is also used for Canadian and USA standards. It features a palm simulator and a restricted joint movement, which simulates the characteristics of the human hand. The finger is made of stainless steel and the rest of the instrument is Delrin®. Handle is designed to accept either a banana jack or a force gauge.It is no longer necessary to have a separate probe for the medical safety standard. This one probe will meet all the different requirements that are in the IEC standards.
-
product
10G Pin Photoreceivers
Macom Technology Solutions Holdings Inc.
MACOM offers PIN photodiode based photoreceivers in a variety of packages, including OEM module and instrument-style. A wide range of 10G solutions are available for applications up to 15 Gb/s covering 800-1650 nm wavelengths.
-
product
50 Pin Breakout Interface
VSI-Breakout-50
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
