Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
VTAC Wired
VTAC Wired configurations reduce resistance and increase signal integrity with a seamless transition from wire to connector. This can be demonstrated in an example using the results of VPC quality and performance testing on VTAC patchcords. The results are reflected in the graph below. Insertion loss was tested on one-meter long patchcords with SFP+ terminations on either end. The second data line (red) shows the same patchcord, but bisected and terminated with VTAC connectors in its center. The results show no significant deviation from the SFP signal until approximately 6.25 GHz. Even at 6.25 GHz, there is only -1dB of difference between the two patchcords, which is approximately a 10% loss. With signal integrity playing such an important role in high speed testing, the obvious choices for high bandwidth data testing are VTAC Wired products.
-
product
6-Port Hardened Industrial Gigabit Ultra PoE DIN-Rail Switch
TI-UPG62
4 x Gigabit Ultra PoE ports2 x dedicated SFP slots240 watt power budget12 Gbps switching capacityHardened IP30 rated metal switchIncludes DIN-rail and wall mountsExtreme -40 to 75 ºC (-40 to 167 ºF) operating temperature rangeDual redundant power inputs with overload current protectionAlarm output triggered by power failurePower supply sold separately (TI-S24048)
-
product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
*ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch*24-port fully managed Gigabit Ethernet switch*Pre-installed ADLINK PacketManager accelerates packet processing*Layer 2/3 switching with advanced support for VLANs, QoS and IPv6*Two 10 Gigabit Ethernet SFP+ uplink ports*Supports IPMI based on PICMG 2.9 (System Management Specification)
-
product
Intel® Xeon® E3 Quad-Core 10 Gigabit Ethernet AdvancedTCA® Processor Blade
aTCA-9300
The ADLINK aTCA-9300 is a high performance AdvancedTCAR (ATCA) processor blade featuring dual 4-core IntelR XeonR processor E3 1275V2 /1225V2, IntelR C216 Chipset, four channel memory up to 32 GB of DDR3 memory and 300 W power supply subsystem. Versatile connectivity includes dual 10GbE Fabric Interfaces, dual GbE Base Interfaces, quad front panel GbE egress ports, front panel dual COM and USB 2.0 ports and front panel VGA connector. An onboard SATA connector supports CFast up to 32 GB and the optional RTM (aTCA-R6270/R6280) supports an 8-channel mini-SAS port, dual 10GbE SFP+ ports, dual USB ports and dual hot-swappable SATA bays providing additional network throughput and storage capacities.
-
product
100BASE-T1 SFP Module
Art.-Nr.: TE-1430
Convert between 100BASE-T1 and Standard Ethernet The 100BASE-T1 SFP Module is the optimum solution to convert between 100BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 100 Mbit/s full-duplex 100BASE-T1.
-
product
Multi Checker
AMC-70
AMC-70 can check SFP TX and RX power level by simply inserting SFP into it. If you use UPM (Universal SFP-typed Power Checker Module) provided. AMC-70 can measure optical power.
-
product
1000BASE SFP Transceivers
CommFront offers a range of high-quality, high-performance SFP transceivers ranging from MM 850nm / 0.3 miles (550m) to SM 1550nm / 100 miles (160km). SFP (Small Form-Factor Pluggable) is a compact, hot-pluggable network interface module used for data communication and tele-communication applications. SFP equips with one or two fiber optic connectors (e.g. LC connectors) for connecting a fiber optic cable or sometimes an RJ45 connector for connecting a copper cable. Because of its compact size and flexibility, many Ethernet Switches come with SFP ports so individual ports can be equipped with any suitable type of transceiver as required.
-
product
Optical Fiber Transceivers
Optical Fiber Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP). Fiberinthebox provide a full range of optical transceivers, such as SFP+ (SFP Plus) transceiver, X2 transceiver, XENPAK transceiver, XFP transceiver, SFP (Mini GBIC) transceiver, GBIC transceiver, CWDM/DWDM transceiver, 40G QSFP+ & CFP, 3G-SDI video SFP, WDM Bi-Directional transceiver and PON transceiver.
-
product
NI-7935, Xilinx Kintex-7 K410T FPGA, Controller for FlexRIO
783766-01
The NI‑7935 features a programmable FPGA and embedded processor optimized for deployment in the field for reliable, extended operation for applications requiring advanced I/O capability with embedded signal processing. It includes a Xilinx Kintex‑7 K410T FPGA, 2 GB of onboard DDR3 DRAM, a dual‐core ARM Cortex‑A9 processor running NI Linux Real‑Time, and 2 SFP+ ports for data streaming. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
4-port LAN Module With Intel® I350-AM4/I211-AT Ethernet Controller
AX93336
The AX93336 LAN module is built with an Intel® I350-AM4/I211-AT GbE Ethernet controller, incorporating Jumbo Frames and Intel® VT-c (Intel® I350-AM4) to optimize network traffic processing. It also comes with an optional LAN bypass function to ensure smooth network connectivity at all times, making it an ideal solution for users seeking better protection of their essential business communications in the event of a power outage, system shutdown or crash. This LAN module’s high-density design is specifically adapted for Axiomtek’s 1U and 2U rackmount network appliances, featuring four 1 GbE RJ-45 or four SFP ports plus a PCIe 2.0 x8 golden finger for expansion flexibility, giving customers the freedom to streamline their individual network infrastructure deployments to fulfill fast-changing networking demands quickly and cost-effectively.
-
product
One Core Loop Tester
DAMUL is an innovative and portable optical power checker accompanying 1-core loop back function. DAMUL can check SFP TX and RX power level by simply inserting SFP into it. If you use UPM (Universal SFP-typed Power checker Module) optionally provided, DAMUL can measure optical power. Also, when using SPM (SFP-typed Power checker Module) optionally provided, DAMUL can identify 18 CWDM wavelengths as well as its power automatically. DAMUL provide users high productivity for optical power checking work on fiber optic systems such as WDM-PON.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
PXIe System Sync Module, 2 Port
M9032A
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
product
Quickly & Accurately Validate Any Pluggable Transceiver from 10M to 100G
iOptics
iOptics offers a complete, powerful and easy-to-use tool for CFP and QSFP qualification and can validate the full range of low- to high-rate transceivers including SFP, SFP+, XFP, CFP, CFP2, CFP4, QSFP+ and QSFP28. iOptics offers a faster, streamlined and automated test sequence aimed at quickly and simply validating any type of 10M to 100G interface. It is the ideal solution for multirate field commissioning with a simple one-button pass/fail. It offers automated stress testing for lab qualification and is also ideally suited for data center and data center interconnect (DCI) testing.
-
product
SFP+ Cable, 3m
784076-03
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
FOTS-ORL
S-120
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
16 Channel VME Digitizers
SIS3316
With the SIS3316 you have the option to use an Ethernet SFP or an optical SFP medium to implement non VME readout.
-
product
Dual-Port HS-1760 Test & Simulation PXI Express Module
PXIe-C1760
Avionics Interface Technologies
3U PXI form factor fits into PXIe or PXI hybrid slotTwo independent ports programmable as NC or NT(s) simultaneouslyTwo SFP sockets accepts FC-0 AS5653 or AS5625/AS5627 transceiversSupports NC-to-NT transfers, NT-to-NC Transfers, Mode Codes, and BroadcastFull control of sequence and exchange managementSupports large file exchangesFull Monitoring of all Bus TrafficTriggering and FilteringFull Error InjectionSupports DMA for high speed streaming of data to/from the boardIRIG-B Time Code Encoder/Decoder for Data CorrelationOptional Special FC-0 physical layer compliance with SAE AS5653Optional fcXplorer Analyzer for decoding HS1760 frames
-
product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Gigabit Ethernet
SFP Transceivers - Copper
Copper SFP transceiver modules (1000Base-T) are 100% compatible with Cisco equipment, include RJ-45 connector, and compliant with applicable industry standards.
-
product
Gigabit Ethernet
SFP Transceivers - 1000Base SFP
SFP transceiver modules (1000Base SFP) from M2 Optics are 100% compatible with Cisco equipment, include LC connectors, and are compliant with industry standards.
-
product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
ATCA Rear Transition Module
ART108
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
product
Fiber Cable, Multimode, OM3, 100m
784184-100
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
100Gbps Ethernet Packet Generators
Axtrinet (AXTRINET IS A TRADING NAME )
1x 100GbE QSFP28 port, 4x 25GbE SFP28 / 10GbE SFP+ / 1GbE SFP ports, Status Indicators
-
product
XMC Mezzanine Module 2 x SFP+
DN3-SHARK XMC 2.0
The DN3-SHARK is a is a XMC standard mezzanine card, equipped with a dual port 10Gbps Ethernet controller.
-
product
3U cPCI Serial Dual-Port SFP+ 10Gbps Ethernet NIC
SN5-TOMBAK
The SN5-TOMBAK is a peripheral slot card for CompactPCI® Serial systems, with a dual port 10Gbps Ethernet controller. Both ports are available via SFP+ front bezel connectors for optical cables via SFP+ transceivers or SFP+ twinaxial copper cables.
-
product
1000BASE-T1 SFP Module
Art.-Nr.: TE-1437
Convert between 1000BASE-T1 (automotive Gigabit Ethernet) and SGMII Interface. The 1000BASE-T1 SFP Module is the cutting-edge solution to convert between 1000BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 1000 Mbit/s full-duplex.
-
product
10Gbit Ethernet Test Engine
XGT-200
The Ethernet test engine XGT 200 provide a comprehensive test for next generation Ethernet solution. There are many different test modules, it can help clients to verify the performance of their Ethernet. XGT-200 have two 10/100/1000Mb/s RJ45 , two 100/1000M SFP and two 10Gbps SFP+ it can generate test profession streams that you need and analyze them ,then provide the test result. XGT-200 provide install and maintain services and activate new profession service. XGT-200 can provide many kinds of test functions, it can help you to control and know the quality of your Ethernet.
-
product
QSFP+ Twinaxial Cable, 5m
785685-05
1-Pin, Male QSFP+ to 1-Pin, Male QSFP+ SFP Cable - The QSFP+ Cable connects to the quad small form-factor pluggable (QSFP) ports on some PXI Ethernet Interface Modules and other hardware devices. The model also has multimode optical fiber options that you can use in tandem with QSFP+ optical transceivers. The cable is rated for transmission speeds up to 40 Gbps and is offered in different lengths.
