Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
EBIRST 100-pin SCSI Termination Fixture
93-019-104
93-019-104 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Magnetizing Fixtures
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
product
Test Fixtures
Canadian Microelectronics Corp.
This fixture clamps to microstrip or CPW lines at the edge of an RF board and is usable at any position without limit on size of circuit. The base is magnetic and it can be locked and released by a knob to accommodate any kinds of circuit configuration. Available for frequency ranges up to 40 GHz.
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Vacuum Test Fixtures
Vacuum fixture kits for Pylon block fixture, Teradyne, Keysight, Digitaltest,Seica, Cobham (Aeroflex), ATX exchangeable system.
-
product
Automatic Fixture Removal
S93007B
The S93007B automatic fixture removal (AFR) is the easiest way to remove fixture effects from non-coaxial device measurements and runs on the PNA/PNA-L/PNA-X Series B model network analyzers
-
product
SMD Test Fixture
16034G
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
product
Burn-In Test Fixtures
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
product
Test Fixture Adapters for In-Circuit Test Fixtures
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
product
Test Fixture Kits
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
product
Test Fixtures
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
Exchangeable Test Fixture
MA 2109/D/H/S-5
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
product
Functional Test Fixtures
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials. The fixture is a section of coaxial transmission line broken to allow the insertion of planar test materials. Although ASTM D4935-10 is currently limited to an upper frequency of 1.5 GHz, the EM-2108 meets and complies fully with both the impedance and SE requirements called out in ASTM test method D4935-10 up to 10 GHz. These results are shown in Figures 1 & 2. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred.
-
product
System Test Fixture
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
-
product
Test Fixture and Test Programing
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
product
Stand-Alone Test Fixture
MA 2013/D/H
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 22,00 kg
-
product
Test Fixtures
REINHARDT System- und Messelectronic GmbH
Is a fixed state of a set of objects used as a baseline for running tests. The purpose of a test fixture is to ensure that there is a well known and fixed environment in which tests are run so that results are repeatable.
-
product
Clamshell Type Mechanical Fixtures
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
product
In‐Circuit Test Fixtures
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
Test Fixture
N1295A
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
product
Magnetic Material Test Fixture
16454A
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
product
Test Fixtures & Test Sets
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
product
Stand-Alone Test Fixture
MA 2013/D/H/Pylon
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 24,00 kg
-
