Filter Results By:
Products
Applications
Manufacturers
PMC
PCI Mezzanine Card
- TEAM SOLUTIONS, INC.
product
GPIB PCI Mezzanine Card (PMC) Interface & Cable
GPIB-PMC-XL
The GPIB-PMC-XL is a PCI Mezzanine Card (PMC) GPIB controller card that converts any CPU card with PMC slots into a GPIB controller.It performs all the basic IEEE-488.1 functions such as talker, listener and system controller. The IEEE-488.2 compatible functions make it fully compliant with the IEEE-488.2 specification. In controller applications, you can control typically up to 15 devices (instruments). If operated as a talker/listener (device) interface it does exchange data and state information with the current controller-in-charge of the GPIB bus. The GPIB-PMC-XL lets Windows and Linux programs control GPIB devices.The flat ribbon cable has a standard GPIB jack on one end and a receptacle to be plugged into the GPIB card on the other end. The 30cm (12in) flat ribbon cable is included by Team Solutions, Inc.
-
product
PMC Module
PMC-MON16LED
• Fully compatible withGE Fanuc / RamixPMC498• PCI MezzanineCard (PMC) IEEE1386• 16 LEDs• Two RotarySwitches for 256Combinations• Read / Writeable• Monitoring LEDs• Front panel I/Oaccess
-
product
Multifrequency Clock Synthesizer - PMC
Model 7190
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
-
product
PMC Mezzanine Front Panel
Front panels according to IEEE 1386 | zinc die-cast or aluminum extrusion
-
product
Interface
RCNIC-A2PA
The RCNIC platform is a high performance PMC module for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
MIL-STD-1553 PCI Interface Card
PCI-1553
Alta Data Technologies’ PCI-1553 and PCIC-1553 (PMC on PCI carrier) interface modules are multi-channel (1-4) 1553 cards supported by the latest software technologies. These PCI cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
product
High Performance Data Acquisition
PMC-AD8
The PMC-AD8 module provides a high performance dataacquisition subsystem. There are (8) eight 200 KSPSADC’s for maximum performance. The Local DSP can beused to simply move data samples to the PMCbus or canprovide processing functions such as limit checking, FFT’s,digital filtering, etc. Software can be downloaded to theDSP via the PMC interface. Instrumentation amplifiersprovide over-voltage protection and gain on a per channelbasis. The PMC-AD8 can also accept external scan andtrigger signals from a front panel connector.
-
product
Mezzanine Module
RS485-MOD2
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
product
LVDS I/O Module
LVDS-MOD3
Curtiss-Wright Defense Solutions
The LVDS-MOD3 is a front panel mezzanine module designed to provide LVDS I/O functionality to Curtiss-Wright's FPGA-based processing PMC modules. This LVDS I/O module provides 32 differential pairs to the front panel. The LVDS-MOD3 LVDS I/O module is aimed at embedded application development.
-
product
Active PMC board
CAN-IB410/PMC
With the CAN-IB410/PMC HMS offers an interface board based on a modern and highly modular concept. The board covers a wide range of field buses, such as CAN (ISO 11898-2), fault tolerant CAN (ISO 11898-3) and LIN. The CAN-IB410/PMC is available with up to four CAN channels with galvanic isolated interfaces. For use in the automotive field the high-speed CAN channels can optionally be switched to low-speed CAN via software. In addition, the card can be equipped with up to two LIN interfaces. Furthermore, the modular architecture of the interface card enables the easy extension with customer specific interfaces via piggyback modules.
-
product
8-Port RS-422 Async Serial Communications Adapter PMC
2316
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS422 signaling levels
-
product
8-Port RS232 Async Serial Communications Adapter PMC
2229
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS232 signaling levels. Each port provides the full set of data and modem control lines configured for DTE
-
product
PMC Analog Out Board
MS 1821
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*32 channel single ended analog Output*Unipolar or bipolar voltage output*Programmable output voltage: 0-5V, 0-10V, 0-10.8V, ±5V, ±10V, ±10.8V and is capable of driving up to +/-20mA*16 bit Resolution*Conversion time 10usec typ*Over current protection*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
product
Mezzanine PMC
PMC-E2001
Curtiss-Wright Defense Solutions
The PMC-E2001 keeps low speed, high quality analog IO simple and takes care of ruggedization for youThe PMC-E2001 combines analog input and output channels and is an application-ready module engineered to perform precise using sigma-delta devices for waveform generation and reconstruction for audio and acoustic applications.
-
product
PMC Module
PMC-1553-TACEx
Operating temperatureCommercial: 0 to +70 °COptional: -40°C to +80°C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 20’000 ft
-
product
PMC Intelligent Interface Card
IIB-1553-PMC
The IIB-1553-PMC is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the PCI Mezzanine standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card.
-
product
ATCA Rear Transition Module
ART103
The ART103 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC103 carrier board. The ART103 is a passive RTM that allows for the additional connectivity of two GbE ports, Management 10/100Mbit Ethernet, Management RS-232 serial interface and three PCIe x4 lanes for expansion. One of the PMC J4s (user defined I/O) is routed to the back.
-
product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
product
Radar Scan Converter PMC
Eagle
Curtiss-Wright Defense Solutions
Eagle is a flexible and powerful radar scan converter that is based upon field-proven technology and comes in a compact and mechanically ruggedized PMC form factor. Eagle features a low power, rugged design, enabling it to operate in a wide range of environments, including conditions of high temperature and vibration.
-
product
cPCI to PMC Compatible Adapter/Carrier
cPCIBPMC6UET
cPCIBPMC6UET ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up to two PMC cards into a standard cPCI slot. cPCIBPMC6UET has two PMC card slots mounted to a universal voltage 6U 4HP cPCI card.
-
product
Expansion Adapter Chassis
TB3-TO-CMC-LP
The TB3-TO-CMC-LP is an expansion adapter chassis using the Intel Thunderbolt 3 interface. The adapter allows the use of a front I/O XMC or PMC card outside its normal confines of a single board computer (SBC) or PC hosted carrier card. The TB3-TO-CMC-LP enables the deployment of XMC or PMC modules in systems previously unable to host them -- laptops, small form factor PCs, and other computers lacking add-in slots.
-
product
PMC Bus Analyzer / Exerciser
PMC650
The PMC650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
product
6U cPCI PMC carrier
DP-cPCI-5400
In general, PMC cards provides modular and cost effective solution for engineering various applications in process control, medical electronics, aerospace, defence and telecom sector.
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
PMC (ccPMC VITA 20)-to-4X PCI Express (PCI-e/PCIe) Adapter
6773
Our Conduction-Cooled PMC (ccPMC VITA 20)-to-4X PCI Express (PCI-e/PCIe) Adapter w/ VITA 46 Differential I/O (6773) permits the insertion of a single PMC into a PCI Express (PCIe/PCI-e) slot (4X). The adapter orients the ccPMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector.
-
product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
product
Dual PMC Carrier for 6U CompactPCI
TCP262
The TCP262 supports standard PMC front I/O and CompactPCI rear I/O fully compatible to the TCP260. The PMC slot 2 (upper PMC) I/O lines are connected directly to the CompactPCI connector J5. The PMC slot 1 (lower PMC) I/O lines are connected directly to the CompactPCI connector J3.
-
product
PMC to PCI Express Adapter w/ TSI384
6083
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI express primary side and a PCI/PCI-X secondary side.
-
product
CompactFlash Card
PMCF3
PMCF3 is a COTS IEEE 1386.1 compliant PMC with removable CompactFlash card up to 6 GB that offers a convenient way to add large capacity, non-volatile memory to rugged system solutions. Targeted at the world's defense and aerospace OEM marketplace, this cost-effective CompactFlash adapter is ideal for use with our families of COTS SBCs and PMC carrier cards.
-
product
PCI to PMC Adapter/Carrier
PCIBPMC
1/2 Length Bridge Based PCI Adapter Carrier Card with PMC Mounting Slot. The PCIBPMC ( PCI Bridge PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCIBPMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit bus operation. The PMC user IO connector Pn4 is brought out to one of two connectors for access (DIN IDC or SCSI II). The signals corresponding to the PrPMC standard Ethernet and Serial lines can optionally be connected to the Ehternet and Serial port connectors at the top edge of the board.
