Filter Results By:
Products
Applications
Manufacturers
TAPs
network jump enabling undetectable data monitoring. AKA: Test Access Points
See Also: Network Monitoring, Network Taps, Aggregator Taps
- Applied Instruments, Inc.
product
CATV Return Band Two Carrier Generator
PC-2
The PC-2 is a compact, temperature-stable two RF-carrier source. It is designed to be used for activating and testing the return-band. When used with a signal level meter, the PC-2 assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.
-
product
Copper TAPs
Profitap Copper TAPs provide complete access and visibility into your network by creating an exact copy of full-duplex 10M/100M/1G/10G traffic at wire speed with no impact to the network link. Profitap Copper TAPs introduce no point of failure to the network. They are designed for redundant powering, which allows a second power supply to activate if the first were to become unavailable. In case of complete power loss, Profitap Copper TAPs guarantee that the link remains operational by instantly switching to a fully passive mode.
-
product
RF Taps
Praxsym’s RF Taps afford access to a cable system for monitoring function and performance without interrupting service. The taps also cause minimal insertion loss when the coupled port is open, as in normal system operation. Like all Praxsym products, these high-quality devices have honest specifications, and are well-documented over the bands they are designed for.
-
product
SparkFun 6 Degrees Of Freedom Breakout
LSM6DSO (Qwiic)
The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DSO breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature!
-
product
Bypass TAPs
Bypass TAPs provide fail-safe access for active in-line network security and performance tools. In the event that an active in-line tool becomes unavailable, either due to a hardware malfunction, power loss, software problem, or planned maintenance, bypass TAPs ensure the network link stays operational.
-
product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
product
High-Performance Intelligent Pod for Corelis Boundary-Scan Controllers
ScanTAP 4 & 8
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires equipment with high-performance specifications and extended features.Corelis ScanTAP pods are designed for use with PCI-1149.1/Turbo and PCIe-1149.1 high-speed JTAG controllers. Featuring 4 & 8 independent Test Access Ports (TAPs), up to 80 MHz clock rates, and advanced TAP capabilities such as analog voltage measurement, the ScanTAP family of intelligent pods is the ideal JTAG interface for high-performance environments.
-
product
Handheld Broadband Noise Generator
NS-1
The Model NS-1 is a handheld broadband white Gaussian noise source. It generates a wide, even, RF noise-signal. The NS-1 is popular for testing network components and aligning a building's coaxial cable network. The NS-1's noise-signal is also used to provide the RF source for measuring insertion loss of cable, splitters, taps and more.
-
product
RF Couplers
Directional, bi-directional, dual-directional and RF Taps; over 475 models with power handling from 0.5 to 300W covering DC to 65 GHz!
-
product
Copper Network TAPs
Network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers copper network TAPs in network speeds of 10/100M or 10M/100M/1000M (1G). Copper TAPs are purpose-built hardware devices used for out-of-band monitoring tools and make a 100% copy of your networks data allowing your monitoring tools to see every bit, byte and packet.®
-
product
SM / Expansion Unit
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
product
Multi-ratio CT Auto Test Box
PCT200 Series
The ATB01 PCT200 series Auto Test Box is specially designed as an accessory of PCT200i and PCT200Ai for automatic testing of the multi-ratio CT with multiple taps.
-
product
Filtering Network TAPs
Filtering network TAPs allow you to filter out the packets and traffic that is not needed by the tool to perform its function. Filtering ensures that monitoring ports do not become oversubscribed with unneeded data. Filtering TAPs are purpose-built hardware devices that let you see every bit, byte and packet.®
-
product
Outdoor Exposure Tester
OET
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
product
Hipot Tester
NX Hipot+
* 50 to 1500VDC Hipot Testing * 50 to 1000VAC (optional) * Expandable to 1024 test points * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
product
Robotic Probing of Circuit Cards
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
-
product
Design for Test
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
product
CATV Pocket Calibrator & Return Band Signal Source
PC-1
The PC-1 is a compact, temperature-stable RF-carrier source. It is accurate enough to calibrate spectrum analyzers, signal level meters or any other receiving devices. When used with a signal level meter, the PC-1 CW test signal generator assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.
-
product
Fiber TAPs
Profitap fiber TAPs provide secure in-line network access for the monitoring of 1–400 Gbps fiber networks. By splitting the light flowing on the network link, fiber TAPs deliver an exact copy of the data for real-time monitoring and analysis, without disrupting the network. Passive fiber optic TAPs require no power, and therefore introduce no point of failure when deployed in a network.
-
product
Switch Box for CT Analyzer
CT SB2
The CT SB2 switch box is an accessory for the CT Analyzer which allows automatic testing of multi-ratio current transformers. It is connected to all taps of the current transformer and to the CT Analyzer.
-
product
ABex Terminal Module for JTAG Technologies JT 37x7 BSCAN Cards
ABex TM-JT37x7
The ABex TM-JT37x7 is an ABex terminal module for the JTAG Technologies Boundary Scan Controller PXI/PXIe JT 37×7. In combination with the JT 2147/ABex from JTAG Technologies it integrates the POD functionality into the module.In combination with the PXI/PXIe JT 37×7 and the JT 2147/ABex it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
product
Boundary-Scan Test and In-System
PCIe-1149.1
The Corelis PCIe-1149.1 is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the PCIe-1149.1 offers up to 80 MHz clock rates on 4 or 8 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
Regeneration TAPs
Regeneration Fiber TAPs allow the tapping of fiber optic networks, while mitigating the power reduction of the optical signal that results from splitting.
-
product
Bypass Network TAPs
Bypass TAPs (bypass switches) are used to connect a monitored network segment to an active, in-line security device and monitor the device's health. If your security tool goes off-line, the bypass TAP automatically 'switches to bypass mode' keeping your network link up while you resolve the issue. Garland's Bypass TAPs with failsafe technology guarantee 100% network up-time and let your security devices see every bit, byte, and packet.®
-
product
Serial / USB Communications
Advantech offers serial / USB converters, isolators, repeaters, surge suppressors, data taps /splitter, USB hubs, and industrial communication cards.
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
product
Test Database Software Module
The relational test database is the pivotal point of the software structure. On one hand, this is where the test applications and test systems used for productive testing are stored; on the other hand, it provides the storage space for all DUT-related test data. Depending on customer requirements, the test database may either be hosted locally on the test system or centrally on a server, supporting several test systems. The database performance is sufficient for a high-volume production environment with many test systems which access the central database in parallel. LXinstruments prefers to implement the database as a license-free MySQL database; it is however also possible to realize a version based on Microsoft SQL.
-
product
PXIe-8522, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module
787312-01
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8522 also provides LEDs on the front panel to help you monitor the network link and activity.
