Filter Results By:
Products
Applications
Manufacturers
- CAMI Research Inc. (CableEye®)
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
CAMI Research Inc. (CableEye®)
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large library to match your connector. Then touch the tester probe to the connector pins one-by-one to automatically detect and assign a test point to each pin. A synthetic voice reads probed pins as you touch them so you don’t need to take your eyes off the connector you’re probing. Finally, enter pin labels of your choice if you wish to override the standard designations.
-
product
ICE 3000 Series
ICE3005
The ICE3005 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in a cosite environment and is factory configured for an ARC-210 interface. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the two-port design. The ICE3005 also includes a separate audio processor circuit that mitigates popping and drop-outs in the R/T audio that are common in hopping or blanked waveforms. The ICE3005 incorporates extensive Built-in-Test capability and is qualified for military applications. A mounting tray is available for easy incorporation on your platform. Cost-effective modifications are available on the ICE3005. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
Preamplifiers
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
product
Impedance Matching Pads
Surface mount and coaxial 50 Ohm / 75 Ohm impedance matching pads for CATV systems, broadband networks, test setups and more!
-
product
Discrete Detectors
TRAL test station is a quasi-universal test station designed to measure parameters of discrete (or small linear array) infrared detectors sensitive in a wide spectral range from about 700nm to about 16 000 nm (NIR/SWIR/MWIR/ LWIR detectors or broadband non selective detectors). All main types of infrared detectors can be tested: photonic detectors: photovoltaic/photoreconductive, cooled/non-coooled, thermal detectors, pyroelectric detectors etc.
-
product
ICE 3000 Series
ICE3006
The ICE3006 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in the cosite environment. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the three-port design (LOS and SATCOM). The ICE3006 incorporates extensive Built-in-Test capability and is qualified for airborne applications. A mounting tray is available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3006. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX02
The N5293AX02 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 110 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
product
Test Set Solutions
This product category contains specialized low-PIM filter-based offerings for 3GPP/4G/5G LTE test sets and broadband emissions monitoring.
-
product
120 GHz Frequency Extender, Pulsed DC Bias
N5295AX02
The N5295AX02 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 120 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
product
Calibration
RF Test Equipment
We calibrate following types of RF test equipment:EMF test systems (frequency selective)EMF test systems (broadband)Field strength transfer standards (e.g. RefRad)Line Impedance Stabilisation Network (LISN)Cable, attenuator, couplerAntennaField Probe
-
product
Horn Antenna
TDK HRN-0118
The TDK HRN-0118 broadband horn antenna (1 GHz to 18 GHz) is designed specifically for radiated emissions and immunity measurements in EMC test environments. The HRN-0118 horn antenna provides optimal performance over the frequency range of 1 GHz to 18 GHz.
-
product
RF And Microwave Modules
Unlike specialized RF and microwave module product suppliers, Shengbo Technology has accumulated rich experience in designing and developing broadband microwave test products. As a sophisticated RF and microwave test system, a large number of high-performance RF and microwave modules are required for system integration. To this end, we have conducted in-depth research.
-
product
Microwave Measurements & VNA Calibrations
Rosenberger Hochfrequenztechnik GmbH & Co. KG
For microwave measurements and VNA calibrations, Rosenberger develops, manufactures, and provides test & measurement products which meet the highest demands of industrial test applications. These include high-performance VNA test cableswith outstanding phase and amplitude stability, a variety of test port adaptors for VNA applications up to 110 GHz, very robust interchangeable high mating cycle port connector systems, and test devices – from low-frequency devices for simple measurements to components permitting high-precision broadband measurements.
-
product
2.0 ~ 68.0 Gb/s Pulse Pattern Generator
CA9809
The UC INSTRUEMNTS CA9809 2.0 ~ 68.0 Gb/s Pulse Pattern Generator pulse pattern generator and error detector is a high performance, flexible and costeffective broad band data rate covered Pulse Pattern Generator that can operate from 2.0 Gb/s to 68 Gb/s. The CA9809 can be used with existing equipment to generate higher rate bit streams for use in telecom applications up to 68 Gb/s. Broadband test systems will benefit from the low power dissipation, precision connectors, and excellent output waveform characteristics. The compact size of the equipment allows the CA9809 to be placed at the measurement plane, reducing or eliminating artifacts related to long cables.
-
product
2-Way Power Dividers
KRYTAR 2-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 2-way power dividers can also be manufactured to meet military specifications.
-
product
2 GHz Dual 1:4 RF Mux, 75 Ohm Module for 34970A/34972A
34906A
The Keysight 34906A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies--create a stubless 16:1 multiplexer in a single frame.
-
product
Wide FOV Target Projector
The Model 13792 is a broadband portable target projector used for characterizing the performance of a wide variety of infrared sensor systems. The system incorporates SBIR standard components to provide accurate and precise stimulus to sensors under test in laboratory, depot and production line environments. Testing can be automated with the use of IRWindows™ test system controller that reduces test times and cost, while improving the consistency and accuracy of test results.
-
product
Light Sources and Amplifiers
Light sources simulate the optical voice, video and data signals of real-life service applications, which is why they are used in various types of tests. Discover a broad range of products that cater to various testing requirements: singlemode or multimode, polarized or non-polarized, broadband or narrowband, tunable, ITU-wavelength-centered and much more.
-
product
USB Power Sensor - 100 MHz To 8 GHz, Average, Peak (Pulse), Pulse Profile
GT-8552B
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
product
Broadband DSL Test Set
Copper Pro 990DSL
The 990 CopperPro Series II provides a full range of troubleshooting, fault locating, testing and qualification capabilities. That means top performance with fewer tools to carry.
-
product
Noise Source, 1 GHz up to 40 GHz
346CK40
The Keysight 346CK40 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 40 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source greatly reduces measurement uncertainty, which are commonly reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 14 dB at 1 GHz, decreasing to 5 dB at 40 GHz (typical).
-
product
Serializer/Deserializers & Selector Muxes
Serializer/Deserializer muxes use both rising and falling edges of the clock to serialize the data from parallel inputs to serial output while demuxes deserialize the data from its serial input to parallel outputs. Selector muxes routes the differential inputs to either one or more of the desired outputs upon assertion of the appropriately selected port. Muxes can be used in various applications including High Data Rate Ethernet, Fiber Communication, Signal Routing and Broadband Test & Measurement Equipment.
-
product
10 MHz to 55 GHz Noise Sources
CNS346 Series
The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.
-
product
Broadband Network Test
Whether testing via Voice Switch, DSLAM, OLT or external access device, Enghouse LoopCare comprehensively manages testing in mixed technology networks.
-
product
Broadband Test
458-3SLB
This compact, versatile unit accepts 1, 2 or 3 line modules or other products that use Telebyte's convenient line module form factor. At home in the lab or a high-volume production environment, it is capable of controlling from 1 - 24 channels and is ideal for testing DSL modems and other bandwidth-compliant telecom devices. While it can be used as a stand-alone unit, the built-in Control Module interfaces with a PC via RS-232, IEEE-488, or Ethernet. In addition, the 458 Universal GUI (included with purchase) may be used to control the unit from a PC. For added convenience, the Control Module firmware is field-upgradeable through the RS-232 port.
-
product
Combitesters
No other tester offers so many interfaces and functions: combines all commonly used broadband (xDSL, GPON, LTE) and Gigabit Ethernet interfaces with comprehensive triple-play functions in a single measuring device. It is the integrated all-in-one tester that combines all current test scenarios in one single, multi-functional, handy and intuitively operable device.
-
product
USB Power Sensor - 10 MHz to 18 GHz, True-RMS Average
GT-8553B
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
product
Vibration Table Top, series
OVTT 24
The OVTT, OmniAxial Vibration Table Top, series introduced the first stand-alone, compact, repetitive-shock vibration system on the market and features Qualmark's patented six-degree-of freedom vibration technology. The OVTT24 system provides 77% more table surface area than the OVTT 18 which makes it an ideal tool for in-production-line, broadband spectrum vibration testing of product. It is also ideal for quick evaluation of field returns, repair verification and random vibration testing of multiple small products and can be configured for placement inside a thermal chamber for combined stress tests.
-
product
MLDD 8-Way Power Dividers
KRYTAR MLDD 8-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR’s power dividers offer the widest frequency coverage in a single package on the market and provides superior performance. Targeting broadband electronic warfare (EW) systems and complex switch-matrix applications, for example, KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 8-way power dividers can also be manufactured to meet military specifications.
-
product
ICE 3000 Series
ICE3009
The ICE3009 subsystem is an agile filter for the VHF-L, VHF-H and UHF frequency bands. It allows operation of a number of transceivers in a cosite environment. The VHF/UHF Filter provides multiple poles of RF selectivity to reduce broadband noise in transmit mode of operation and to reduce interfering signals at the transceiver’s RF input in receive mode at Have Quick II/IIa and SATURN tuning speeds. This design incorporates a flexible control scheme that can be configured at the factory for various radio interfaces (ARC-210, ARC-231, ARINC 429, etc.). The design is highly integrated and includes all filters, amplifiers, power supply, transmit and receive switching (including a bypass mode), and Built-in-Test (BIT). A mounting tray is available as an option for easy incorporation on your platform. This system is qualified for military applications. Cost-effective modifications are available on the ICE3009. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
