Filter Results By:
Products
Applications
Manufacturers
Ionizers
Neutralize static charge.
-
product
Multifunction Voltage Tester
*Detects AC voltage by non-contact method: 70VAC to 250VAC*Finds broken wire location*Wrong connection check*Ground / Earthing disconnection check*Detects static radiation of TV / monitor*Checks operating condition of ionizer*Microwave leakage detection: ≥5mw/cm2
-
product
Air Ion Counter
The Air Ion Counter is a handheld meter designed to measure ion density-- the number of ions per cubic centimeter (ions/cc) in air. It measures this number separately for positive and negative ions (+ and - ions are usually present simultaneously). This instrument is a true ion density meter, based on a Gerdien Tube (Gerdien Condenser) design, and it contains a fan which pulls air through the meter at a calibrated rate. The standard model measures up to 2 million ions/cc (for comparison, outdoor air typically has 100 to 1000 ions/cc, both + and -). The 2 million range is sufficient for almost all situations except for measuring very close to electric ionizers or strong radioactive sources.
-
product
Charge Plate Monitor
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
product
Bench Top Ionizers
Point-Of-Use Ionizer, Adjustable (30-100 PSI) Compressed Air IonizerNeutralize Electrostatic Attraction (ESA) to control contamination by dislodging dust and debris attracted by static electricity.Detachable 7'' long ESD Protective Flexible Hose with Thumb Button Designed to for a wide range of motion and simple operation.Adjustable Balance (20 Volts) with Less Than 1 Second Discharge Time At 6 InchMeets required limits ANSI/ESD S20.20 tested per ANSI/ESDSTM3.1 and ESD TR53
-
product
Periodic Verification System for Measuring Static Charges and Verifying Ionizer Performance
STME-PVS
Statclean Technology (S) Pte Ltd
This meter is designed to measure static charges and to verify ionizer performance. It consist of three components- an Electrostatic Fieldmeter, a Detachable Plate and a Charger.
-
product
Analytical Balaneces
AT-R Series
Basic Model with Improved Convenience.*Freely set responsiveness or stability*Connect with a computer via USB or RS232C*Perform stable measurements in combination with an ionizer
-
product
WINSTAT
WINSTAT is an air ionizer developed for the purpose of eliminating static for every industries. As a wide range of product types is offered, the device can be used for various kinds of applications, including the desktop use and for the line use, etc.
-
product
PRODUCTS TESTING
ESD
MicroStat Laboratories -R.E.T.S.
Our ESD test capabilities include resistance, resistivity, electrostatic shielding, charge generation, and charge dissipation. We routinely test flooring materials, packaging, footwear, garments, ionizers and many other ESD control products and materials. We utilize the relevant test methods and standards of the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, AATCC, or our clients’ in-house specifications.
-
product
Ionizers
ESD
Electrostatic discharge (ESD) is the release of static electricity when two objects come static control ESD IT-7000 Tabtop ionizerinto contact. Familiar examples of ESD include the shock we receive when we walk across a carpet and touch a metal door knob and the static electricity we feel after drying clothes in a clothes dryer. A more extreme example of ESD is a lightening bolt. While most ESD events are harmless, it can be an expensive problem in many industrial environments.
-
product
Pulse Air-Gun Ionizers
EC-G Series
Panasonic Industrial Devices Sales Company of America
With the new Pulse Air-Gun Ionizer from Panasonic, operators can comfortably neutralize static electricity while manually cleaning. The Pulse Air-Gun’s light-weight, ergonomic design combined with an oil and heat-resistant 2m cable makes it ideal for use at the production line.The Air-Gun Ionizer is equipped with a white LED on the front of the Gun to illuminate target objects. It has three air emission modes: long pulse, short pulse and continuous emission. Ionized air can be emitted at high pressure (range 0.05 to 0.50 MPa), neutralizing static charges and removing dust simultaneously and swiftly.
-
product
Charged Plate Monitors
Model 156A
The Trek Model 156A Charged-Plate Monitor System is designed to provide quantitative measurements of the effectiveness of air ionization systems, as to audit ionizer performance. The Model 156A employs a revolutionary charged-plate monitor design that utilizes an ultrahigh-impedance, high-voltage follower to monitor the ion collecting plate voltage.
-
product
Basic Field Kit
PFK-101
The PFK-101 includes the PFM-711B Electrostatic Field Meter, CPM-720B Charge Plate Monitor and PCS-730B ±1 kV Electrostatic Charger for measuring ionizer decay and balance.
-
product
Charged Plate Monitor
Model 280A
Simco-Ion’s Model 280A incorporates enhanced circuitry that enables it to more accurately measure the performance of high frequency AC ionizers, as well as pulsed DC ionizers and steady-state DC ionizers. The Model 280A can be used as a portable CPM and is capable for of up to 6 hours of operation on the internal battery before recharge.
-
product
Bench Top Ionizer Cleaning Box
EC-B
Panasonic Industrial Devices Sales Company of America
The EC-B Bench Top Ionizer allows direct ion emission to be paired with pulsed air emission to provide quick and effective removal of static charges as well as any dust that is present on the part. Three white LEDs illuminate the work piece to ensure complete dust removal. A powerful dust collecting fan exhausts dust quickly, preventing re-adhesion of dust.
-
product
Ultra Compact Ionizers
ER-V Series
Panasonic Industrial Devices Sales Company of America
The ER-V Ultra-Compact Ionizer offers a new style in charge removal. It uses high frequency AC in an ultra-compact Ionizer for superior static elimination.
-
product
PIEZONIZER
This is an air nozzle ionizer incorporating an ultra-small-size high-voltage transformer without any high-voltage wiring. Since it operates only on DC power input, its wiring has become much simpler.
-
product
Closed-loop Ionizer Controllers For Multichannel Voltage Detection
Novx 3352/3362
Simco-Ion’s Novx brand of Passive (Model 3352) and Active (Model 3362) Multi-fan Closed-loop Ionizer Controllers provide the capability to simultaneously detect, measure, record and monitor electrostatic voltages in multiple locations. The versatile antennas used with these systems allow their use in a variety of applications including monitoring sensitive workstations, in-tool voltages, or ionizer performance with the option of closed-loop control to select ionizer products.
-
product
Electrostatic Field Meter Kit
PFK-100B
- Measure range & polarity of electrostatic fields in 1 volt or 10 volts increments- Charges from zero to over 1000 volts in less than 5 seconds- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Use with a datalogger to record measurements & create reports- Compatible with the Autoanalysis System- Accuracy of ± 5%- Battery Operated
-
product
Voltage Touch Monitor
The AlphaLab Voltage Touch Monitor enables personnel to identify voltage problems that usually remain hidden. The monitor reads the voltage on a finger (which is identical to the voltage at every other point on the body). It can detect as little as 1/10 volt in two modes: DC and AC/Spikes (ESD transients). In the DC mode, the displayed voltage is either positive or negative, and is usually very low if grounding is being worn and is functioning properly. Higher DC voltages (even while grounded) occur if a DC ionizer is blowing too close or if the person rubs against a high-static material or comes in contact with metal at a DC potential. If personal grounding is not being used, any DC signal can build up over time, and the DC mode continues to show the instantaneous body voltage as it changes. In the AC/Spikes mode, any transient voltage spike at least 1/2 millisecond long is temporarily displayed. If there are several consecutive spikes, only the highest is displayed, regardless of polarity. If the signal is a repetitive (AC) wave, the peak voltage is displayed, but always as a positive number. Even when proper grounding is worn, several tens of volts often occur with transients and AC. Maximum error for DC and AC is only 2% of the reading +/- 0.1 volt.
-
product
Pulse AC Method Area Ionizers
ER-X Series
Panasonic Industrial Devices Sales Company of America
The ER-X Series Area Ionizers utilize the pulse AC ionization design to achieve high-speed charge removal of wide surface areas for high-volume production lines. In addition to supporting compressed air ionization, the ER-X also features both airless and low-pressure ionization modes for applications where tiny workpieces can be easily blown away. Additional features include automatic ion balance and discharge frequency control (manual control is also possible), flat discharge surface for easy cleaning, discharge needle air barrier design to reduce contamination of the needles, replaceable discharge needle unit for easy maintenance, and a dual head configuration for enhanced charge area and layout (2 different ionizer heads can be connected to a single controller).
-
product
Static Control/UV Curing Devices
Panasonic Industrial Devices Sales Company of America
Static Controls (Ionizers)Panasonic offers static elimination tools and Sensors in various form factors, to fit specific application requirements.UV Curing DevicesPanasonic offers LED and lamp spot-type UV Curing Systems. These systems can be controlled manually or integrated into automated applications and configured with replaceable heads, cables and lenses to best fit application requirements.
-
product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
-
product
Tabletop Ionizing Transport System
90610-03610
The Model IT-7000 Ion Transport System is a self contained, compact table top ionizer capable of producing copious amounts of both positive and negative ions. The variable speed fan permits a gentle flow of ionized air, reaching a distance of up to 4 feet. A charged object, when passed through the ionization field, becomes neutral instantaneously. Inherently balanced, the Ion Transport System has a fail safe balance indicator to assure proper ionization output for ESD static control applications.
-
product
Periodic Verification System
Model 775 PVS
The Simco-Ion Periodic Verification System Model 775PVS is a hand-held alternative to a charged plate monitor. It consists of three components-a fieldmeter, a detachable plate, and a charger for measuring static charge and verifying ionizer performance. Used alone, the fieldmeter measures electrostatic fields on any surface.
-
product
Static Remover (Ionizer)
STABLO-AP
STABLO-AP provides reliable measurement by removing static electricity.
-
product
Static Control Devices
Panasonic Industrial Devices Sales Company of America
There are many production processes where electrostatic charges disturb smooth operation. To eliminate static, Ionizers are used.Whether the application is for the Semiconductor industry where the components are extremely sensitive and can even be damaged by high electric static charges or for the packaging industry, where plastic sleeves or foils tend to stick to each other, Panasonic has a solution to neutralize electrostatic charge.
-
product
Walker Test Set
PGA-710B
A unique electrostatic data analysis device for use with Prostat’s PFK-100 Field meter/Charge Plate Monitor Set.• Records, plots, analyzes and automatically constructs reports of body voltage generation, electrostatic decay, voltageretention, ionizer performance and other static measuring functions.• Creates detailed reports to help determine the risk of equaling or exceeding damaging or hazardous HBM dischargevoltages in static sensitive facilities.• Analyze Footwear & Flooring Combinations: Records personnel walking voltages in accordance with ANSI/ESD STM97.2 Body Voltage measurements as required by ANSI/ESD S 20.20 ESD Program Standard• Other Equipment Applications include voltage generation of chairs, carts and process equipment
-
product
Fan Type Ionizer
ER-F
Panasonic Industrial Devices Sales Company of America
With a compact size of 150 x 166 x 62mm and a fan of 120mm in diameter, the ER-F Fan Type Ionizer belongs to the leading class of compact Fan Type Ionizers. The system employs a high-frequency AC method and boasts a +/-2kV discharge output voltage that discharges electrostatic contaminated objects quickly and safely. Louvers for long distance and wide area applications are shipped with the Ionizers. Standard fan types for faster charge removal times and low-volume types for discharging small parts or film are available.
-
product
Compact Fan Type Ionizers
ER-Q Series
Panasonic Industrial Devices Sales Company of America
With Panasonic’s high-frequency AC method and “Sirocco Fan”, the ER-Q Compact Fan Type Ionizer can remove electrostatic charge even at slow fan speeds.ER-Q Ionizers are extremely compact and well suited for removing localized electrostatic charge on manufacturing equipment for electronics or in Semiconductor processes. The ER-Q Ionizers require no compressed air which eliminates air lines and reduces additional maintenance.
-
product
Ionization Kit
PIK-110
The PIK-110 Ionizer Test Kit contains all the instrumentation included in the PFK-101 as well as advanced equipment making it the most comprehensive portable ionizer test equipment available.
