Filter Results By:
Products
Applications
Manufacturers
Mezzanines
Is the stacking of cards into a single card that then plugs into the computer bus or data path.
- TEAM SOLUTIONS, INC.
product
GPIB PCI Mezzanine Card (PMC) Interface & Cable
GPIB-PMC-XL
The GPIB-PMC-XL is a PCI Mezzanine Card (PMC) GPIB controller card that converts any CPU card with PMC slots into a GPIB controller.It performs all the basic IEEE-488.1 functions such as talker, listener and system controller. The IEEE-488.2 compatible functions make it fully compliant with the IEEE-488.2 specification. In controller applications, you can control typically up to 15 devices (instruments). If operated as a talker/listener (device) interface it does exchange data and state information with the current controller-in-charge of the GPIB bus. The GPIB-PMC-XL lets Windows and Linux programs control GPIB devices.The flat ribbon cable has a standard GPIB jack on one end and a receptacle to be plugged into the GPIB card on the other end. The 30cm (12in) flat ribbon cable is included by Team Solutions, Inc.
-
product
Voltage Meter
MDN8I
MDN8I is a mezzanine module designed for high-precision measurements in dynamic signal analysis systems, as well as for joint work with ICP sensors and vibration transducers with a charge output (force sensors, dynamic pressure, acoustic emission, vibration displacement, etc.). The MDN8I mezzanine module has electrical characteristics no worse than those of most foreign and domestic counterparts, and in some parameters exceeds them.
-
product
PMC Mezzanine Front Panel
Front panels according to IEEE 1386 | zinc die-cast or aluminum extrusion
-
product
Mezzanine System
5041
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
product
Mezzanine System
5089
The 5089 provides eight channels of 12 bit A/D conversion using the Analog Devices AD7328, and is suitable for medium resolution medium speed applications.
-
product
Mezzanine Module
RS485-MOD2
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
product
Transceiver
MT
Mezzanine MT (mezzanine transceiver) is designed to receive and transmit microwave signals in the frequency range from 70 to 6000 MHz. The MT transceiver is a new generation device designed using the most modern element base and designed for use in modern measuring systems based on the open standards AXIe, VXI and LXI.
-
product
IC-RBP-XMCa, Active network redundancy XMC Switch Mezzanine Card
IC-RBP-XMCa
IC-RBP-XMCa, Active network redundancy XMC Switch Mezzanine Card
-
product
LVDS I/O Module
LVDS-MOD3
Curtiss-Wright Defense Solutions
The LVDS-MOD3 is a front panel mezzanine module designed to provide LVDS I/O functionality to Curtiss-Wright's FPGA-based processing PMC modules. This LVDS I/O module provides 32 differential pairs to the front panel. The LVDS-MOD3 LVDS I/O module is aimed at embedded application development.
-
product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
-
product
Digital Digitizer
MOS2
Mezzanine module (mezzanine) MOS2 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values. The mezzanine is intended for use in HF and microwave systems as a terminal device for digitizing intermediate frequency signals up to 200 MHz. Together with the frequency converter DOWNCONVERTER 10 GHz LXI manufactured by the holding "Informtest" MOS2 under the control of the common software shell ACM2 makes up a synthetic instrument - spectrum analyzer, a ready-made solution for testing microwave devices and radio reception channels.
-
product
Passive XMC-to-PCI Express Adapter
5944
The Technobox, Inc. P/N 5944 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 5944 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
product
FPGA Mezzanine Card (FMC)
FMC DEL
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) created to produce pulses delayed by a user-programmed value with respect to the input trigger pulse. It has 4 output channels and one input trigger. The delay from the trigger input to each of the outputs can be set independently in a range from 600 ns to 120 seconds. It is implemented using a dedicated time-to-digital converter IC from the European company Acam.
-
product
Mezzanine PMC
PMC-E2001
Curtiss-Wright Defense Solutions
The PMC-E2001 keeps low speed, high quality analog IO simple and takes care of ruggedization for youThe PMC-E2001 combines analog input and output channels and is an application-ready module engineered to perform precise using sigma-delta devices for waveform generation and reconstruction for audio and acoustic applications.
-
product
Quad 12.0 Gsps 16-bit DAC FMC+ Module
DAC-Q30
The DAC-Q30 FMC+ module from DEG is a high sample rate, 16 bit quad channel DAC module. The Analog Devices AD9174 DAC device operates at 3.0 Gsps natively and up to 12.0 Gsps in interpolation mode. A VITA 57.4-compliant FPGA Mezzanine Card (FMC+) interface, the DAC-Q30 offers industry wide platform compatibility with the PCIe/VME/VXS/VPX carrier board of your choice. The DAC-Q30 and associated HDL firmware are compatible with AMD FPGAs.
-
product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
product
FMC for High Speed Optical Communication Dual QSFP+ FMC
FMC424
Sundance Multiprocessor Technology Ltd.
The FMC424 is a dual QSFP+ FPGA Mezzanine Card. Electrically compliant with the VITA 57.1 standard the FMC424 is compatible with 4DSP FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC424, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and optical communication solution while using a single FMC site on an FPGA carrier card.
-
product
XMC
Switched Mezzanine Card (XMC) a type of PCI Mezzanine Card especially used in rugged environments.
-
product
MicroTCA Systems
Pixus Technologies offers customized MicroTCA® shelves and system solutions. With expertise in xTCA systems, along with backplane and cooling specialists, Pixus will help you create a winning µTCA design. MicroTCA is a modular, open standard for building high performance switched fabric computer systems in a small form factor. MicroTCA systems utilize standard Advanced Mezzanine Cards (AMCs) which provide processing and I/O functions. MicroTCA targets smaller telecom systems at the edge of the network, as well as mobile, military, telemetry, data acquisition, and avionics applications.
-
product
PMC Intelligent Interface Card
IIB-1553-PMC
The IIB-1553-PMC is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the PCI Mezzanine standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card.
-
product
Flight-Certifiable Avionics Interface
RAR15XC
The RAR15XC flight-certifiable avionics communications board delivers high-density MIL-STD-1553 and ARINC 429 data bus communications as well as avionics discrete I/O. Its small XMC mezzanine form factor is easily integrated onto other compatible boards, like the SBC314C flight-certifiable single board computer.
-
product
Power Supply Voltage Generator
MON12
*The mezzanine MOH12 is a module designed to generate supply voltages through twelve galvanically isolated channels.*The MOH12 mezzanine is installed on the mezzanine carrier - the NM-M (NMU) module and is connected to it via a local information highway. Up to four MOH12 can be installed on the NM (NMU) module.*The NM-M (NMU) module together with the mezzanines installed on it forms a VXI module of the C-1 size and is used to create information measuring VXI systems.
-
product
*Shelf Manager Carrier/Mezzanine Board for CompactPCI
064-758
Set of Shelf manager mezzanine board installed on the pluggable carrier board. The pluggable carrier board provides all interfaces on the rear connectors.
-
product
Image Processing Module
IMP20
The IMP20 video processing mezzanine card significantly increases the ease of acquiring and interpreting images from multiple sensors and cameras, thus speeding reaction time and potentially saving lives. The card adds image fusion capabilities to Abaco Systems’ ADEPT104 and AIM12 automatic video trackers, and allows the design of highly integrated, high performance graphics capabilities in any environment where the input from multiple devices needs to be combined in order to provide a complete, easy-to-interpret image.
-
product
Mezzanine FMC
FMC-518
Curtiss-Wright Defense Solutions
The FMC-518 provides high-speed, low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of the data delivered to the FPGA host through the FMC-518.
-
product
Mezzanine System Carrier
MMS8010 / MMS8011
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
Virtex 7 FPGA Carrier
PC7: 330/690
The PC7 family of FPGA carrier boards is DEG’s latest AMD-based product innovation. With the ability to host two FMCs (FPGA Mezzanine Cards) with rear panel I/O, the PC7 product line sets the benchmark for performance and versatility in the embedded PCIe market. Coupling this flexibility with a AMD Virtex-7 VX330T or VX690T FPGA, the PC7 enables multi-channel high-speed data acquisition and extensive digital signal processing all within a single PCIe slot.
-
product
Oscilloscope
MOSTS6
*MOSTS6 is the first Russian instrument (oscilloscope) with a direct sampling rate (8bit ADC), 5 Gigasemp / s per channel. M-module MOSTs6 is designed to work as a part of information measuring systems based on the VXI bus magister as a digital oscilloscope. The M-module is made in the form of a triple-width mezzanine, is installed on a mezzanine carrier and is connected to it via a local information highway.*MOSTS6 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values, measure time intervals between two instantaneous voltage values through two independent channels.MOSC6, according to the conditions of use, meets the requirements for measuring instruments of group 3 in accordance with GOST 22261-94.
-
product
1-2 Independent, Dual Redundant 1553 Channels on Small Mezzanine
MEZ-E1553
From our popular ENET product, the MEZ-E1553 is a small, rugged mezzanine product that can easily be integrated into your system design. Alta provides full reference schematics, design notes, STEP 3-D Files, and sample ESS test programs. Guaranteed 1553A/B/C compliant with AS4111 5.2 Protocol Test reports.
-
product
Mezzanine System
3564
The 3564 is a four channel comparator board with a common mode range of -150V to 150V on the two differential inputs and a DAC per channel to set trigger levels. The high common mode range and DC coupling provides a robust solution to level detection and triggering.
