Filter Results By:
Products
Applications
Manufacturers
Harness
A multi-routed assembly of connectors, wire and cables.
See Also: Cable Assembly, Harness Test, Test Harness, Wiring, Wire, Connectors
- CAMI Research Inc. (CableEye®)
product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
CAMI Research Inc. (CableEye®)
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
-
product
Cable/Harness Tester
CR
As a wire harness tester, a cable tester, a continuity tester, a component tester, and a guided harness-assembly aid, the Easy-wire CR tester is versatile. The easy-wire CR features Windows based software that allows you to create custom graphics of your connectors and light LEDs to guide the harness assembly process. Test Points: 256-32,000, Test Current: 6.5 mA max
-
product
1 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97103
1' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
6 Ft Harness, 78 Pin Male Connector On One End, Loose Wires (numbered) On Other End
GX96105
6 ft harness, 78 pin male connector on one end, loose wires (numbered) on other end.
-
product
Cable Harness EM Solver
MHARNESS
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
CAMI Research Inc. (CableEye®)
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
CAMI Research Inc. (CableEye®)
A USB Type-C test interface board for CableEye® cable and harness testing systems. Consisting of a daughter board, populated with two USB-C female connectors, it allows users to continuity-check USB Type-C terminated cables using the CableEye tester while seeing the connectors-under-test rendered graphically. The CB26U fits all CableEye models.
Configuration
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test. Sold as a set of two boards, each CB26U accepts two USB Type-C connectors. In addition to the latest CableEye software, it requires the CB26 small-frame motherboard (Item 756) for operation, and plugs into one of two available slots – two USB-C-connectors can be tested simultaneously. The CB26 (with CB26U) attaches to the tester like a regular connector board.
Contact sales@camiresearch.com or +1 (978) 266-2655 for a quote. -
product
1-Slot Thunderbolt 2 PCIe Expansion
EB1T
Power, Performance, Portability: Enhance the power of your laptop with the Magma ExpressBox 1T and harness lightning-fast throughput up to 20 Gbps over a single cable via Thunderbolt-2 technology. ExpressBox 1T enables serious professionals to use specialty PCIe cards with any Thunderbolt-equipped computer, so that you can achieve high performance wherever your work takes you. Add a PCIe card to ExpressBox 1T and your computer turns into a powerful workstation capable of HD video capture and editing, media transcoding, audio processing, data processing, or high-speed storage and networks. The ExpressBox 1T offers the largest card length slot (7.75”) among all 1-slot Thunderbolt chassis on the market, giving your Mac the power to achieve maximum performance with any compatible half-length PCIe card. Whether your mission involves professional video capture, audio interface, SAS & SATA HBA, 8Gb Fibre Channel, 10 Gigabit Ethernet, or a RAID controller card, Magma’s family of Thunderbolt products provide the perfect outsidethe-box solution for your project.
-
product
Truck Chassis Dynamometer
Truck chassis kit includes: heavy-duty tube-steel frame and 30"-diameter "dually" wide-roll assembly with machined-in "traction grooves," air brakes, diamond-tread deck plate, floor anchors, wheel chocks, vehicle tie downs, eddy-current absorber and controller with overdrive, S-beam load cell, DYNOmite-Pro data-acquisition computer, inductive RPM pickup, DYNO-MAX software, electronic auto-load control, 28-channel data harness, engine-temperature thermistor, and more.
-
product
6 Pin Round Pin Tester / Maintenance Kit
#8027
Innovative Products of America
Test, clean and restore 6 round pin trailer connections. Included tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 6 round connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsPatentedKit Includes: #7897: 6 Pin Round Pin Tester, #8022: 6 Round Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
product
Software Development
In support of system, test and our tooling design, our software development team is ARC’s primary advantage in providing the superior performance in hardware (electrical), mechanical and software cohesiveness. The software team at ARC literally brings all of it together.Whether you want to leverage one of our standard platforms, such as TestCentre or harness the power of the process editor in our PVS software to build up your custom workflow, most customers are impacted by the power and scalability of our software solutions, without sometimes ever knowing the tremendous effort that goes into our software.Customization, whether you are needing work in LabVIEW, TestStand, C# or other development platforms, our team can deliver the perfect solution, tie the mechanical and electrical worlds together in coming up with your next solution.
-
product
SafeBloc
A SafeBloc is an accessory device, which can be used with other test equipment, as an adapter, to connect and test power cords and wiring harnesses for production testing purposes, prior to installation into equipment. Such testing would include Hipot and continuity testing of the power cord or wiring harness. The SafeBloc allows the bare wires of a power cord or wiring harness to be connected to the test equipment via clips inside the enclosure. Power can only flow through the device once it is closed and the test sequence is then started, ensuring that the test operator will not get shocked during the testing procedure. Power cord manufacturers and CEMs manufacturing custom wiring harnesses would be typical users of such a device.
-
product
Test Management Software
Easy to use to minimal training. Our Test Management Software is powerful enough to accommodate all of your electrical and function testing requirements, whether testing a cable harness or fully equipped vehicle or aircraft.
-
product
Cables, Harnesses & Wiring Looms
Amfax manufacture a wide range of wiring harness solutions in a variety of styles and finishes. These wiring harnesses, or looms as they are often called, can be constructed using heat-shrink, conduit tube, braid, tape, tie-wraps or lacing cord.
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
Data-Acquisition Computer
DYNOmite data-acquisition computer with from 3 to over 112 channels (with or without optional LCD display and pushbutton handheld interface), full-bridge strain- gauge-equipped electronic load cell torque transducer, AC power supply/recharger, data wiring harness, engine-temperature thermistor, and protective carrying case.
-
product
Cable Tester
SS8681 Series
The SS8681 series cable tester is used for test and measure wire cable harness, wire harness, like as: auto cable, audio cable, power cable, network cable, telephone cable, USD cable, HDMI cable, video cable, etc.
-
product
RF Coaxial Interconnect System VPX Compatible Rectangular Harness Solutions
VITA 67 Rectangular Harness
VITA 67 is a VPX standard for blindmate coax connectors that allows high density, high performance RF connections to be made between a backplane and plug-in modules.
-
-
product
1' Harness, 50-Pin Male D-Sub Connector
GT97108
1' harness, 50-pin male D-sub connector on both ends.
-
product
Harness Test Fixtures
Doyle Test Fixtures for the manufacturing of Electrical Wiring Harnesses or Assemblies.
-
product
State-of-tha-Art Testing Facilities
With a passion for collaborative listening, planning, contracting, performing, and delivering, Boeing creates a tailored partnership with you to achieve your product testing goals. Capitalize on access to Boeing's proven engineering expertise and right-sized resources in: Aerodynamics, Propulsion, Acoustics, Environmental, Electromagnetics, Structures, Metrology, Simulation, Materials. Whether your testing requirements are big or small, simple or complex, short term or ongoing, well-defined or developmental, you can harness Boeing's innovative and productive energy.
-
product
Systems Integration for Circuit Card Assembly
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
product
Robotics
Teradyne Robotics brings the power of advanced automation to companies of all sizes, everywhere. Our solutions – which include collaborative robots, autonomous mobile robots and motion control software for robots – are safe, reliable and easy to deploy.Through our robotics companies – Universal Robots and Mobile Industrial Robots – we enable you to harness the combined power of machines and human talent to improve operational efficiency. The result is better quality, better products and better business.
-
product
Wire Harness Tester
NX Solo
The Dynalab NX Solo Wire HarnessTester is a low-cost, feature-packed, stand-alone tester with a maximum capacity of 256 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to decide which operation to perform next. Testing for continuity, shorts, and a variety of components.
-
product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
CAMI Research Inc. (CableEye®)
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently. Certain components within models M3U, M3UH, HVX, and HVX-21 (i.e. those capable of measuring resistance) are analog components whose characteristics change slightly over time. This aging is a natural phenomenon common to all electronic components and may cause resistance measurements or gradually deviate from normal. A tester that is out of calibration will give inaccurate results. Some (maybe all) resistance measurements will be incorrect. Consequently, it may Pass what should Fail and, conversely, Fail what should Pass. In other words product yield will be contaminated due to unreliable quality.
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
-
product
Custom Test Fixtures
Intrinsic Quality is proud to offer a variety of Test Fixture Development Services that include fixture building, tester interface building, harness building, troubleshooting, maintenance, design, and engineering. IQ’s fixtures are built to exacting specifications and configured to deliver quality production testing. Our global customers have trusted us for over 35 years to provide custom solutions applying leading edge technology. IQ consistently delivers cost-effective solutions with our client’s recognition and gratitude.
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
