Filter Results By:
Products
Applications
Manufacturers
Potentiometers
Measure the voltage in a circuit or function as voltage dividers.
See Also: Programmable Resistors
- Pickering Interfaces Inc.
product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Automated Potentiometer Systems
Measurements International Ltd.
Intrinsically Accurate Self-Calibrating Ratio Divider, Best Accuracy < 0.05 ppm, Built-in 20-Channel Scanner, Arbitrary Voltages from 1 mV to 1200 V, Bipolar Voltage Measurements, Calibration of Fluke 5700A/5720A, Calibration of 3458A and 8508A, Calibration of Voltage Ratio Dividers (F752A, MI 1340A, G7520), Linearity Calibration of Digital Volt Meters (DVM), Traceability to 10 V Zener Reference.
-
product
Suitable For Temperature And Potentiometer Sensors
SEM1600T
The SEM1600T accepts resistance or mV signals from RTD, Slidewire or Thermocouple sensors.
-
product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Linear Potentiometers
They are one of the most common forms of measuring device for linear position. They are incredibly simple to use relative to other devices, infinite resolution, output is proportional to stroke length and very robust.
-
product
Linear Motion Potentiometers
A spin-off of the Trimpot trimming potentiometer product line, the linear motion potentiometer was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
product
Rotary Position Sensors For Motorsport
Variohm offer a range of Rotary Position Sensors For Motorsport including rotary potentiometers and hall effect sensors. They are suitable for use in Morotsport application such as pedal, steering and gearbox applications.
-
product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
-
product
Plug and Play Potentiometer Input Module
DSCUSB-PT
The DSCUSB-PT is a compact, high-precision potentiometer input module; converting a resistance based input (potentiometer) to a digital output. Can be used with resistance based sensors to indicate position, rotation and angle. Aimed at applications which require high accuracy. Simply by plugging the device into a PC, data can be extracted from the potentiometer input to the DSCUSB-PT for a wide range of applications. This is achieved using the DSCUSB Toolkit software, which is a simple configuration tool designed specifically for configuring DSCUSB modules. It allows configuration, calibration, logging and parameter management of the modules.
-
product
IGBT Power Supply, 24 KW, Output 0 to 16 VDC, 1500 AMPS, P/N 6133C
IGBT Power Supply, 24 KW, P/N 6133CInput: 480 VAC, 3 PH, 60 HzOutput: 0 to 16 VDC, 1500 AmpsRipple does not degrade when the output voltage is reducedDigital remote with Voltmeter and Ammeter and potentiometers includedDimensions: 20.00”W x 20”H x 24.5”D.Estimated weight: 200 lbs.
-
product
PXI Potentiometer Module 5x8 Bit, 0 Ohm to 255 Ohm
40-296-021-5/8
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
Potentiometers
We offer wear-free, low-cost potentiometers that work exceptionally well anywhere precise and careful controls, inputs, or measurements are needed. If your application needs displacement and/or angle sensors, Hoffmann + Krippner, in exclusive partnership with German manufacturer Altmann GmbH, can provide high-quality potentiometer solutions. Furthermore, Hoffmann + Krippner’s ultra-thin, fully-sealed, and easily customized Sensofoil® membrane potentiometers can fit into restricted installation conditions and offer extremely long lifecycles. Similarly, Hoffmann + Krippner SensoInk® allow us to create polymer potentiometers that combine the advantages of PET (flexibility and cost) with high-strength polymer pastes that can surpass the lifecycles of other PET-based potentiometer products.
-
product
DCPs
Renesas offers a wide selection of low-to-high resolution digital potentiometers (DCP) in single, dual and quad configurations that are accurate, easy to adjust, and reduce manufacturing complexity.
-
product
PCI Standard Programmable Resistor Cards
Pickering's PCI Standard Programmable Resistor Cards include fully programmable resistor and potentiometer cards for applications such as sensor emulation that require fine adjustment with a resolution down to 0.25 Ohm. All of our Programmable Resistor Cards can easily be formed to make Programmable Potentiometers by connecting two channels in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
product
PXI Resistor Module Dual 24-Channel (no resistors fitted)
40-281-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Modbus Analog Output Modules
DAT3020 Series
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
product
Commercial Panel Controls
Panels controls are designed for applications that typically require frequent adjustment. Both rotary and slide panel control types are available. A selection of elements includes carbon, cermet, and conductive plastic. These devices are available in various sizes and shaft/bushing combinations. Some models are available with a rotary switch and seal options.Typical applications include audio mixing consoles, test and measurement equipment, consumer electronics, and medical equipment.Turns-counting dials are designed for use with precision rotary potentiometers or other types of panel controls where a turns-indicating device or an adjustment setting/locking device is needed.These devices are available to fit various shaft sizes in digital or concentric scale (analog) readout options. Typical applications include power supplies, oscilloscopes, medical equipment, and industrial automation equipment.
-
product
DC Power Supplies
DCS Series
AMETEK Programmable Power, Inc.
The DCS Series of 1 kW, 1.2 kW and 3 kW programmable power supplies provides a highly reliable power platform. It utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a low profile chassis. This DCS power supply family has an easy-to-use front panel with 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and over voltage protection, status and constant-voltage/current mode operation. The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/local programming and preview status of voltage, current and OVP setpoints.
-
product
Resistance Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitters for resistors and potentiometers in 6 mm housing with calibrated range selection. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
Linear Actuators
Electrak 205
Electrak 205 actuators feature multi-step positioning capability through a 10-turn potentiometer for precise feedback control when used with Thomson actuator control systems. With adjustable integral limit switches, the automatic shut off travel range can be easily adjusted. Fully gasketed housing and motor safety seals protect internal components from harsh industrial environments.
-
product
Motorized Potentiometer
INELTA Sensorsysteme GmbH & Co. KG
More than 10.000 Variants. Free configurable.
-
product
Network Sensor Interface for USB Pressure Transducers
SI314
The Validyne model SI314 is a network interface that connects our model P61 USB pressure Transducer to your smart phone or network web browser. The SI314 supports Ethernet and Wi-Fi connections and will display current pressure readings and transducer status on any web browser or via smart phone. The SI314 also displays the transducer temperature, date of calibration, model and serial numbers and these can be viewed wirelessly or by Ethernet connection. The SI314 makes your P61 accessible from anywhere in the world. Data logging of pressure data is configured via a web browser or smart phone and readings may be stored once per minute to once per hour. A thumb drive or memory card collects the data in comma separated file format(csv) for download to your computer. The data may also be accessed via the network. A graph of the data is also generated on request. A Twitter function allows pressure data to be tweeted from the SI314 at user-defined intervals. The transducer zero and span calibration adjustments are password protected and operated via browser buttons. No potentiometer adjustments are required to calibrate the P61 transducer. Contact our Sales Department for a link to the Demo!
-
product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
product
High Power Digital Lab Series Regulated DC Power Supply – 3000W
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
product
Motorized Potentiometer
Mounting On Circuit Board Or DIN Rail
INELTA Sensorsysteme GmbH & Co. KG
*PCB mounting*Suitable as: setpoint device or rotary actuator*Compact in design* Robust aluminium housing* Gear safety clutch
-
product
10Ch Electronic Potentiometer 8 Bit
YAV90084
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
product
Linear regulated power supply with thyristor pre-regulation
NTN
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
product
Hydrostatic Level Sensor
2250
The Signet 2250 Hydrostatic Level Sensor for level and depth control has a one-piece injection-molded PVDF body and ceramic diaphragm for superior compatibility in corrosive liquids. Utilizing hydrostatic pressure, the 2250 Level Sensor disregards false level signals from steam vapors, foam or any other debris on the liquid surface. Two pressure ranges allow for optimal resolution matched to your sensing needs. Solid state circuitry eliminates drift (no internal potentiometers).
-
product
Actuator
SAM-AC
High - dynamic universal push - pull and turn actuator for test stands. Pedal, cable or potentiometer linkage
