Filter Results By:
Products
Applications
Manufacturers
TCP/IP
Protocol suite governing internet communication.
- Cytec Corp.
product
Analog or Digital Communications Switching Systems with D Type Connectors
RS Series
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps. A modular design concept is used that provides configuration flexibility by allowing display modules, different control modules and switch modules to be combined into a single chassis.LED displays and switch point status feedback are available on most systems. Computer control via IEEE488 (GPIB) and RS232 is standard, while TCP/IP Ethernet LAN, USB and manual controls are optionally available.
-
product
Compact Ultrafast 50-50,000 sccm Mass Flow Controller/Meter
C-Series
The C-Series Mass Flow Controller (MFC) is a compact, fast-response model using a Micro-Electro-Mechanical Systems (MEMS) based flow sensor for non-corrosive gas applications. It is available in Full Scale flow rates from 50 sccm to 50 slm (N2 equivalent) with a control range from as low as 0.1% of Full Scale up to 100% of Full Scale and is also available as a flow meter. Analog (0 to 5 VDC) or digital (RS485 or Modbus TCP/IP) communications interfaces are available. Required power supply voltage is 24 VDC nominal.
-
product
Ethernet Digital Interfaces
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
product
Zero Air System
Model T701
Teledyne Advanced Pollution Instrumentation
The T701 adds Modbus TCP/IP connectivity to the proven reliability and performance of our zero air systems. This allows remote monitoring of key instrument functions including dewpoint status, scrubber temperature, box temperature, and output pressure. Additionally, this digital access provides the ability to remotely disable the internal pump, allowing longer service intervals and less power consumption. The user can also remotely start instrument warm-up prior to arrival at the site.The T701 is a fully self-contained source of clean, dry air for dilution calibrators. It can also be used to create purge air for permeation tube ovens or burner air for FID analyzers. The T701 includes a dewpoint sensor, an oil and diaphragm-free pump, and scrubbers to remove SO2, NO, NO2, O3, H2S, and NH3. Optional high performance scrubbers are available to remove CO and Hydrocarbons.
-
product
Ethernet Digital Interfaces
Model 8063
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
product
Ethernet To Modbus RTU Interfaces
ICS's Ethernet to Modbus Interfaces provide Modbus TCP/IP to Modbus RTU serial conversion and Raw Socket (Telnet) to control Modbus RTU Slave Devices. Available in small Minibox™ and OEM board formats. OEM board has Ethernet, GPIB and USB interface ports. All Interfaces include the VXI-11 protocol for use with: LINUX, UNIX, SunOS, Apple OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems.
-
product
Battery Monitoring System
IPQMS-C64
The iPQMS is the premier battery monitoring system in Eagle Eye's IBwatch-Series. It ensures backup power systems are optimally maintained in large-scale environments. The iPQMS is the main processing unit that measures up to 448 jars (or 448 cells) utilizing up to seven Relaying Units (RU). Each RU connects up to 64 jars (or 64 cells) and captures data from these batteries and sends it to the MPU in real-time. The iPQMS can be used over a private network via TCP/IP, or locally with RS-232. Networked systems can utilize SMS/Email alerts during an alarm outbreak. If you do not wish to use our Battery Management Software, Modbus protocol is available for third-party integration. Flexible expanding solutions allow multiple iPQMS units to monitor all your systems in real-time.
-
product
cRIO-9805, 4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO
786993-01
4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO - The cRIO-9805 is a 4-port Ethernet switch that provides additional ports with 802.1AS network synchronization capability over the 1000 Base-TX network interface. This module supports TCP/IP and UDP network protocols in DHCP + link-local, DHCP, static, and link-local network IP configurations. The cRIO-9805 auto-negotiates communication rates of 10, 100, or 1000 Mbps with its four internally switched ports.
-
product
Ruggedized Small-Size Telemetry System, Requiring Laptop for Display and Control
LS-84-EC
The Lumistar LS-84-EC “Economy Chassis” Telemetry System offers a low cost, high performance COTS solution for a portable quick look ground/remote/airborne station. The unit has a built-in computer running Windows 10 (WIN 7 option) for stand-alonecontrol or can be controlled remotely over TCP/IP. Using Lumistar’s PCI-based or modular line of telemetry products, acomplete telemetry ground station can be configured in a very small space. Functions such as RF reception, demodulation, bitsynchronization, simulation, frame sync, decom, data archive and real-time display can all be handled in this unit. Data can bearchived on an internal solid state drive or external serial ATA or USB 2.0 drive. A laptop using a network connection providesremote control and access to real-time displays. The I/O connections from individual PCI cards are hardwired internally within the chassis, thus allowing a bulkhead mount configuration on the rear panel of the chassis.
-
product
Time Repeater
VCH-402
Time repeater VCH-402 is designed for use in TCP/IP networks as a Time Server of the first level (NTP Stratum1).The time repeater is built on the basis of a single-board microcomputer running under the Linux operating system.
-
product
Ethernet Parallel Interface
Model 8113
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
product
Ethernet-GPIB-USB to Modbus RTU Interface
Model 9009
* All interfaces provide full control of the Modbus RTU slave devices.* Ethernet port supports VXI-11, raw socket and Modbus TCP/IP to Modbus RTU conversion. * GPIB port works with any IEEE-488.2 compatible GPIB controller.* USB port uses Microsoft supplied driver to prevent operating system change problems.* The 9009 uses a simple command set that is accessible from any port.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls. Works with Agilent, NI and Kikisui VISA libraries* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Ethernet interface protocol is fully VXI-11 compliant and does not require special PC drivers.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* OEM oriented board designed for integration inside the user's system with only one cable. On board regulator works with 5 to 15 Vdc power.* Support programs Include ICS's VXI-11 and VISA keyboard control programs and a NTML page utility for uploading your customer webpages.
-
product
Remote Service TV Signal Analyzers
Remote service TV signal analyzers are designed for continuous monitoring of the television distribution systems, their components and other electronic devices. A distinctive feature of these analyzers is the Ethernet interface which allows creating a centralized system for cable network monitoring controlled by the TCP/IP local network.
-
product
CAN/Ethernet Gateway
CAN-ETH
CAN-ETH is a CAN to Ethernet gateway specifically designed to interface CAN networks with TCP/IP networks.
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
Datalogger
iLOGPlus
Infinite Industrial Informatics Lt
iLOGPlus RTU/Data Loggers are internet enabled devices, specially suited for remote data acquisition, distributed telemetry and remote control. The units act as master devices and send alerts and data files on their own via FTP, email and SMS. All types carry a built-in TCP/IP webserver with live webpages that can be accessed by any Internet browser application. They accept and serve TCP and SMS commands for interactive operation in a SCADA system.Analog inputs and digital I/O are expandable by means of I/O expansion modules, plugging on a serial I/O expansion bus.
-
product
Multiple Protocol Interface
AVT-423
Advanced Vehicle Technologies, Inc.
Multiple protocol interface. Ethernet (TCP/IP) to control computer (Client). Fully capable interface with room to grow in functionality and capability. One channel of 2-wire high speed Classical CAN. One channel of either 2-wire high speed Classical CAN or Single Wire CAN (SWC); software selected. Two channels of 2-wire high speed CAN-FD. Two channels of LIN or KWP (software selected). User programmable automatic features. Six more channels of LIN can be added. Status: Full production, normally in-stock.
-
product
The Internet Control Message Protocol (ICMP)
ICMP Tests
The Maxwell Pro ICMP Test Suite provides a series of tests for verifying correct operation of ICMP. The tests ensure TCP/IP compliance through vulnerability and robustness testing, with tests for ICMP in both the IPv4 and IPv6 environments.
-
product
LAN⇔RS-232C Conversion
SI-60
SI-60 is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. Therefore, you can use it for factory automation without worry.
-
product
Modbus Master TCP/IP Component for .NET
WSMBT
WSMBT is a powerful and simple to use .Net component that makes it easy to access data from a Modbus slave device connected to the PC's Ethernet network. Simply drop the component on your form and talk to your device with your VB.NET, C# or Managed C++.
-
product
Serial-to-Ethernet Converter
MultiNet
MultiNet is a communications module that provides GE Multilin serial ModBus IEDs with ModBus TCP/IP communications over Ethernet, allowing connection to fiber optic LAN and WAN network systems. MultiNet has the capability to connect up to 32 serial ModBus devices eliminating complex wiring and additional communications converters, and providing a streamlined and economical Ethernet hub.
-
product
Terminal Emulator
Distinct IntelliTerm
Distinct IntelliTerm is a terminal emulator that allows you to access data on diverse corporate information servers such as IBM mainframes, IBM AS400, UNIX and VAX systems from a single application. It includes full featured terminal emulation for TN3270E, TN3270 for Type 3278 and 3279, with support for 3179G, 3192G, 3472G and 3279 S3G graphics, TN5250 and VT52 through VT420. Distinct IntelliTerm operates over the Telnet protocol running over TCP/IP, an area in which Distinct is a market leader. Distinct IntelliTerm integrates related utilities such as multi-connect FTP with SOCKS proxy support, print server support with LPD and 3287 printing support, substantially reducing your training and support costs.
-
product
Battery Monitoring System
iPQMS-C128
The iPQMS is the premier battery monitoring system in Eagle Eye's IBwatch-Series. It ensures backup power systems are optimally maintained in large-scale environments. The iPQMS is the main processing unit that measures up to 448 jars (or 448 cells) utilizing up to seven Relaying Units (RU). Each RU connects up to 64 jars (or 64 cells) and captures data from these batteries and sends it to the MPU in real-time. The iPQMS can be used over a private network via TCP/IP, or locally with RS-232. Networked systems can utilize SMS/Email alerts during an alarm outbreak. If you do not wish to use our Battery Management Software, Modbus protocol is available for third-party integration. Flexible expanding solutions allow multiple iPQMS units to monitor all your systems in real-time.
-
product
Multibus Development and Test Tool for ECUs and Networks
CANoe
The versatile software tool for development, testing and analysis of ECUs and entire networks. Bus systems: CAN, CAN FD, LIN, MOST, FlexRay, Ethernet, WLAN, Car2x ITS G5, AFDX, J1708, ARINC429 > Protocols: TCP/IP, SOME/IP, CANopen, J1939, ISO 11783, J1587, MCnet, GMLAN, K-Line, CANaerospace and ARINC 825. Others upon request.
-
product
TCP/IP CCTV Equipment
BitNet
BitNet is a 4-bit digital to Ethernet converter that enables up to four, volt-free contact inputs to be transmitted on to a local area network (LAN). Each input is assigned a unique number to identify any contact that has closed or opened. A maximum of 16 BitNets may coexist on the LAN which will facilitate up to 64 volt-free inputs.
-
product
Vehicle Presence and Data Collection Sensor
FLIR TrafiCam x-stream2
The FLIR TrafiCam x-stream2 combines a digital camera and video detector into a single vehicle presence sensor. Detecting moving and stationary vehicles at signalized intersections, TrafiCam x-stream2 transmits vehicle presence information to a traffic controller via detection outputs or TCP/IP communication for adaptive and responsive signal timing. Each cost-effective TrafiCam x-stream2 sensor helps reduce vehicle idling time and optimize traffic flow.
-
product
Industrial GSM MODEM
QSM-26
Infinite Industrial Informatics Lt
QSM-26 is a DIN rail mount GSM/GPRS MODEM. The unit has a built in Quad Band (850/900/1800/1900MHz) Sierra Wireless Q2687 modem, 2 digital inputs, 2 power relay outputs and a serial RS-232 port. Special AT commands are implemented for TCP/IP based communications.
-
product
TV Remote Service Analyzer
ITM-18
The TV signal analyzer ITM-18 is designed to measure the parameters of television signals of analog and digital (ITU-T J.83 Annex A/B/C standard, including DVB-C) television and transmit the measurement results via a local TCP/IP network to a remote PC. It is installed in the nodes of the cable network for continuous, automatic control of the parameters of the television signal.
-
product
LAN⇔RS-232C Conversion
SI-60F
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
product
Web Data Logger
HD50… Series
Datalogger with integrated Web Server. Wi-Fi and Ethernet connection with proprietary TCP/IP or Modbus TCP/IP protocol.
