Filter Results By:
Products
Applications
Manufacturers
Waveguides
guide the propagation of electromagnetic, light or sound waves.
See Also: Millimeter Waveguides, Optical Waveguides
-
product
Coaxial Waveguide Adapter, 1.0 mm (m), 75 to 110 GHz
W281D
The Keysight W281D is a 1-mm male to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281D is used with the Keysight 8510XF systems.
-
product
Waveguide Amplifiers
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
product
Double Ridged Waveguide Horn
DRH203
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
product
Double Ridged Waveguide Horn
QRH0140
Frequency range: 1 GHz - 40 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 10 W / 20 W
-
product
Double Ridged Waveguide Horn
DRH40
Frequency range: 4 GHz - 40 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
-
product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
-
product
Waveguide Switches
With over 70 years of RF experience, EVERAXIS specializes in designing the most demanding Waveguide Switches in extremely complex systems, including in low quantities.
-
product
Harmonic Mixers
These waveguide bandwidth harmonic mixers are designed for use with spectrum analzyers with diplexers, such as the Tektronix 492 and 494 and the Hewlett-Packard 8555A, 8565A and 8569A. They are also used as phase locking and receiver mixers for antenna measurement systems such as the Scientific Atlanta wide range receivers. When used with an external diplexer*, these harmonicmixers can be used to phase lock millimeter wave sources.
-
product
Fail Safe Waveguide Switches
Waveguide switches enable very rapid switching between two RF channels. Fail Safe Waveguide Switches return to the de-energized position when the power is disconnected and requires a small holding current in the energized position. All models have low VSWR and high power handling capacity. They withstand the full power rating of the waveguide and most models can be pressurized to 0.2 MPa (2 ATO) for high peak power applications.
-
-
product
Predicting Microwave and RF Designs Virtually
RF Module
The RF Module is used by designers of RF and microwave devices to design antennas, waveguides, filters, circuits, cavities, and metamaterials. By quickly and accurately simulating electromagnetic wave propagation and resonant behavior, engineers are able to compute electromagnetic field distributions, transmission, reflection, impedance, Q-factors, S-parameters, and power dissipation. Simulation offers you the benefits of lower cost combined with the ability to evaluate and predict physical effects that are not directly measurable in experiments.
-
product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (f) To WR-12, 60 To 90 GHz
E281CS
E281CS E281CS In-line 1.0 mm (f) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
product
Waveguide Power Sensor
V8486A
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
product
Waveguide Bend
DWG8-WR-2C36.5-2561
Waveguide E-Plan Bend, Frequency 325~500GHz, VSWR 1.3:1, FUGP Flange
-
product
60 GHz Transmitter and 60 GHz Receiver Modules
The 60 GHz transmitter and 60 GHz receiver modules open up ultra high speed, high bandwidth data transmission for widespread use. Pasternack 60 GHz waveguide modules utilizes the globally unlicensed millimeter wave spectrum of 57 GHz to 64 GHz. Our wireless 60 GHz waveguide transmitter and receiver components are ideal for meeting the high speed data transmission needs of companies and developers.
-
product
Microwave Antennas
We are engaged as leading Microwave Antenna manufacturers andexporter of a wide range of Microwave Waveguide Antenna, Waveguide Antenna, Parabolic Microwave Antenna, Conical Microwave Antenna and Pyramidal Microwave Antenna.
-
product
Components - Active Multipliers (FDA)
FDA Series
Farran offers a range of broadband varistor multipliers based on planar GaAs Schottky diodes. All devices are fixed-tuned and operate without bias. They offer high efficiency and full waveguide band coverage
-
product
Coaxial Waveguide Adapter, APC-7, 8.2 to 12.4 GHz
X281C
The Keysight X281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Waveguide Adapter
Waveguide adapters in a variety of waveguide standards / flange types and coaxial connectors
-
product
Signal Generator Extension Modules
SGX
Virginia Diodes, Inc. (VDI) Signal Generator Extension (SGX) modules provide high performance frequency extension of microwave signal generators into the THz range. VDI SGX modules offer full waveguide band coverage and are available from WR15 (50 to 75 GHz) to WR1.0 (750 to 1100 GHz) with additional bands under development. This turn-key, sweepable solution is compatible with any microwave signal generator that meets the input frequency and power requirements.
-
product
Coaxial Waveguide Adapter, 3.5 mm (f), 18 to 26.5 GHz
K281C
The Keysight K281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can be transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.07.
-
product
Pre-Bonded Metalbacked PCB
Teledyne Labtech's significant in-house resources have the capability to satisfy the most exacting demands of complex pre-bonded PTFE Microwave PCB. Our extensive machine shop facilities allows Teledyne Labtech to offer a complete sourcing solution from low volume prototypes to high volume production requirements. Teledyne Labtech can also offer pre-bonded metalbacked PCB with integrated wave-guide transitions and co-planar wave-guides.
-
product
Short
FSXE
The FSXE Fixed Waveguide Shorts and the TSXE Tunable Shorts are available for creation of the shorts circuit conditions in waveguides. The TSXE Tunable Waveguide Shorts are movable shorts, adjustable through at least half a wavelength at the low end of the band. The TSXE Shorts consist of movable noncontacting choke plungers within a straight section of waveguide. The FSXE and TSXE Shorts are provided in five waveguide bands between 33 GHz and 225 GHz.
-
product
Double Ridged Waveguide Horn
QRH400
Frequency range: 400 MHz - 6 GHz VSWR (max): < 2.3 :1Impedance: 50 O (Ohm)Connector: 2xN female Power (CW / Peak): 350 W / 350 W
-
product
Variable Attenuator
VAXE
The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.
-
product
RF Coaxial Probes & Probe Positioner
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
-
-
