Filter Results By:
Products
Applications
Manufacturers
RF Chambers
isolate and supress RF waves.
See Also: Chambers, TEM Cells, Acoustic Chambers, Altitude Chambers, Anechoic Chambers, Climate Chambers, Dust Chambers, Environmental Chambers, ESS Chambers, Humidity Chambers, Refrigerated Chambers, Reverberation Chambers, Salt Spray Chambers, Sound Chambers, Temperature Chambers, Temperature Humidity Chambers, Thermal Shock Chambers, Vacuum Chambers, RF Enclosures
- Pickering Interfaces Inc.
product
PXI 10 x 4 to 1 RF Multiplexer 500MHz 50 Ohm Multiway Connectors
40-755-010
The 40-755-010 is a 50 Ohm high density RF multiplexer (4 to 1) array with 10 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a Souriau multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
-
product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXIe-5654, 10 GHz or 20 GHz RF Signal Generator
783126-01
The PXIe‑5654 features an ideal combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe‑5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications.
-
product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
RF Chamber
HDRF-CHM-SERIES
*RF Chamber Designed and Developed for WLAN , Wireless device testing.*Ideal RF Enclosure for 802.11a, b, g, n, ac Device Testing*Ideal RF Shield for Bluetooth, RFID, 3G Device testing
-
product
Chambers
rf cham·ber ex·per·tise 1. the expert skill and know-how gained from designing and installing more than 10,000 rf chambers and enclosures worldwide 2. having the knowledge to answer questions others haven't thought to ask
-
product
RF Chamber Fixtures
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
product
Aquatic Chamber
6800-18
The 6800-18 Aquatic Chamber is used to measure steady-state carbon assimilation and chlorophyll a fluorescence from algal suspensions, coral, macro algae, and sea grasses using the LI-6800 Portable Photosynthesis System, the preferred photosynthesis system for terrestrial plant research.
-
product
Agree Chamber
King Design Industrial Co., Ltd.
*Applying to Aircraft, Military , Vehicle and all kinds of Electronics products.*The reliability testing will approach the real circumstances nearly.*Simulating the true temperature, humidity and vibration testing in the nature.*Temperature, humidity and vibration testing could be done in the meantime, or separately. *Colorful LCD display panel and micro computer control. *All data be recorded in the floppy disk is easy for analyzing and curve plotting by PC.*Controller of vibration system: Linear, Logarithm, Octave sweep*VTH testing simulate the actual operating environments*Random, Sine, Linear vibration testing
-
product
Stability Chambers
ZoneOne Series
The ZoneOne temperature/humidity chamber provides outstanding stability testing performance for manufacturers of pharmaceuticals, biologics, food, and personal care products. This chamber is easy to use, durable, and comes with the full range of features needed to support a wide range of stability test requirements.
-
product
Freeze/Thaw Chambers
TH Series
The Freeze / Thaw TH series chambers are our state of the art freezer environmental chambers used for a variety of applications. Controls are able to be quickly exchanged for future upgrades or repair.
-
product
Environmental Chamber
REXMED REC-200
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Temperature Chambers
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Temperature chambers are suitable for a broad range of applications from high low temperature testing, and oven for ultra-high temperature, to heat treatment or drying for production lines.
-
product
RFID Chamber
– 80dB RF shielded enclosure (inside dim.- 5’ high x 5’ wide x 7’ long)– Fabrication, Construction, and Transportation– Free standing shielded enclosure design including structural support system– Enclosure will be installed over a continuous 1/8″ dielectric underlay and polyethylene vapor barrier– Modular wood-core panel construction– Bulkhead connector panel – (1) 12” x 12”– RF shielded doors – (2) 2’ x 2’– One (1) Antenna Sinclair Model SP-440-SF2SNF– Shield test per IEEE –STD 299- supersedes MIL-STD-285 (Tested @ 1 GHz)– RAM
-
product
Stability Chambers
Lunaire Environmental is a leading manufacturer of steady state and shelf life testing chambers and walk-in rooms which provide constant climate testing and meet ICH guidelines. These steady state chambers and rooms are perfect for long-term material testing on packaged products in controlled temperature storage. Lunaire steady state climatic test chambers are also ideal for research facilities and laboratories because they simulate wide range of temperature, and temperature and humidity environments. Click here for an overview brochure on Tenney and Lunaire equipment offerings.
-
product
Walk in chambers
Our climate cells are built in the unit assembly system. This allows adaptation to the specific conditions of the effective test room size and shape. The test cells consists of the following main construction groups:
-
product
Near-field Chambers
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.Near-Field chambers are an excellent alternative to traditional far-field ranges; testing that can be accomplished on a far-field range can be accomplished on a Near-Field test range. This method of testing allows an operator to employ an indoor anechoic test chamber at a reasonable cost and avoid the problems associated with weather and security concerns often encountered when using an outdoor test range.
-
product
Anechoic Chamber
EMC-3
A 3 meter test range ensuring fully compliant Emission and Immunity testing. Ferrite and hybrid pyramidal absorbers are combined in a unique pattern within a SmartShield high performance chamber. Operating at a 3m test distance, this chamber is compliant to CISPR-16 with a measurement zone diameter of 1-2 meters.
-
product
Temperature Chamber
SE Series
SE-Series Environmental Chambers are the most fully-featured climatic chambers available on the market. Choose either temperature-only or temperature-humidity testing with wide array of diverse compressor size options, enhanced air baffle, and other standard and optional for superior performance.
-
-
product
Chamber Controllers & Software
Designed off of our previous controller platform with familiar features in an improved interface, added functionality for ease and fewer steps to accomplish your daily testing needs. Remotely monitor and control your chambers and receive text/email alarms. From the home screen users can now manually control, run or stop a profile and view a snapshot of current activity like actual/setpoint values, alarm, datalogging, profile, security, IP address information and more.
-
product
Expendable Refrigerant Chambers
LDF Series
The Bemco LDF Series of wide range expendable refrigerant chambers are designed for low initial cost, rapid temperature cycling, environmental stress screening (ESS), and for handling large thermal loads. These systems are compact for their size, can be bench mounted, and are easily modified to special testing configurations.
-
product
Modular Walk-In Chamber
CSZ''s Modular Walk-In Chambers offers flexibility in designing interior work space with pre-engineered conditioning systems and prefabricated panels that can be assembled to meet virtually any test or size requirement. CSZ uses modular conditioning systems which include refrigeration, air circulation, electrical components, optional humidification needed to control your chamber environment. These conditioning systems are designed for easy installation without taking up valuable workspace in your chamber by utilizing removable panels for easy access to all systems. Each conditioning system is tested at the factory to meet your test specifications.
-
product
Corrosion Test Chamber
CME SF-CCT
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
product
Solar Panel Chamber
Specifically designed for the solar industry, these climatic chambers feature specifically designed fixtures to properly measure almost any component related to solar panels including the actual panels, grid-tied photovoltaic inverters, or photovoltaic cells and modules.
-
product
Environmental Test Chambers
In a class by themselves, TetraTek environmental test chambers use laboratory proven subsystems to produce consistent test results. Each component is carefully balanced with all others to form a perfectly working whole.
-
product
Plant Growth Chambers
Canden offers plant growth chamber that are specifically designed to grow and conduct research on different types of plants/seeds used for research applications and has lighting for vascular plants to facilitate standard plant production, plant pathology research, and seed germination and development. The plant growth Chamber is equipped with PID controller capable of maintaining tight control over the entire temperature range. The controller displays both process value and set value- enabling users to keep tabs on real time chamber process and set point. Canden Plant growth chambers are designed with Diurnal Light controllers that enables the user replicate nature’s day and night cycle during their growth cycle. Chamber has also has additive humidity option. In addition, we can customize the chamber to suit your research application. Please contact our sales team with your needs.
-
product
Settling Dust Chamber
Dust material is placed in a collector, or trough, at the bottom of the chamber, where air nozzles periodically agitate the material, causing a cloud in the chamber. After the agitation, the dust cloud is allowed to settle onto the test sample, which sits above the collector.
-
product
Altitude Chamber
FA Series
Altitude Test Chambers combine temperature and altitude environments with optional humidity for simultaneous environmental testing. An Altitude Chamber allows users to control the test chamber temperature while subjecting the product under test to various levels of altitude 50,000 to 100,000 feet. This combination of elements allows precise simulation of real-life conditions a product might encounter at various altitude levels.
