Filter Results By:
Products
Applications
Manufacturers
Comb Generators
a reference signal source outputing multiple harmonics of the input signal.
See Also: Open Area Test Sites
- Applied Instruments, Inc.
product
CATV Multi Carrier Signal Generators
5112
The 5112 is a portable RF signal generator, available in four or six carrier configurations. Each carrier can be activated individually or simultaneously.
-
product
Comb Generators
Macom Technology Solutions Holdings Inc.
MACOM offers a family of Non-Linear-Transmission-Line (NLTL) GaAs Comb Generators offering superior phase noise performance up to -18 dBc/Hz better then a SRD, usable harmonics out to 50 GHz, and available in SMT or connectorized packages. Standard drive levels from 18 - 21 dBm.
-
product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
Comb Generator, 10 MHz to 67 GHz
U9391G
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator
CG01
The main application of Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble shooting Open Area Test Sites(OATS).An OATS must be completely calibrated before it is put into service. reference signal source Noise Generators Signal Generators
-
product
Low Phase Noise Amplifiers
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
product
Comb Generators
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
product
RefRad Comb Generators
RadRad is a battery-operated comb generator as well as a field source. It is a valuable tool for engineers ensuring the quality of radiated and conducted EMC and EMF measurements.
-
product
Radiating Comb Generators
TBCG1
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
product
Comb Generator
CG 50/500
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN. reference signal source Noise Generators Signal Generators
-
product
Comb Generator, 10 MHz To 110 GHz
U9391M
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Reference Radiators / Comb Generators
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator
CG118
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
product
Generators
Noise Generator
The noise type to be generated is to be selected from the context menu: right-click the section with the noise name and select the noise type you need.
-
product
Microwave Comb Generator
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
product
Generators
Random Vibration
Random vibration Software program is used for testing the specimen resistance to random vibration impact. This program is a part of vibration controller ZET017-U.
-
product
Signal Generators
Are electronic devices that generate repeating or non-repeating electronic signals (in either the analog or digital domains). They are generally used in designing, testing, troubleshooting, and repairing electronic or electroacoustic devices; though they often have artistic uses as well.
-
product
Pulse Generators
Dedicated analogue pulse generators and function generators with true pulse capability.
-
product
Waveform Generators
Drive your test systems forward with PXI instruments from Astronics. Small size, power-packed, and cost-effective, these waveform generators provide the perfect upgrade for your test bench.
-
product
Character Generators
Overlays Text on VideoFront Panel Programmable or via RS232 Computer LinkUp to 32 MCG-2 on one RS232 busGenlocks to either NTSC and PAL automaticallyCharacter/Background Brightness AdjustableFour Character Heights and Four Character WidthsA-Z, 0-9 and Punctuation Marks Character SetBuilt in Menus, Help Screens and Self-testReal Time Clock (RTC) optionRemote Control via RS232 (RJ11 Connector)BNC Video Connectors, 4 Pin MiniDIN on S-VideoTen Pages of Text Storage in MemoryLithium Battery Backup (10 Year Life)Can be powered from external 12Vdc, for Field useCompact Size in a Rugged Aluminum and Steel EnclosureTwo Year Warranty, Made in USA
-
product
Generators
Sine Signal Generator
The Software Sine generator allows to produce sine and constant voltage signals at the DAC output.
-
product
Pattern Generators
PG311P Series
The MicroImage PG311 series of pattern generators are for applications to display custom designed patterns on screen. The PG311 units will overlay the pattern or patterns on top of the video signal provided to the input of the device. The PG311 can be factory programmed with one unique pattern.
-
product
Impulse Generators
Provides pulse widths (measured at the 20% rise timepoint) in the range of 130 ps to 2 ns, amplitudes as high as 100 Volts, with pulse repetition frequencies to 1 MHz.
-
product
Signal Generators
NF‘s function generators have been used in many applications, since NF produced the first Japan-built function generator in 1959.A function generator is general-purpose test equipment used to generate various waveforms and to execute trigger, sweep and gate oscillation.
-
product
Ultrasonic Generators
F&K Physiktechnik develops and manufactures fully digital ultrasonic generators. Ultrasonic power levels are available for fine wire bonding as well as for heavy wire and die bonding applications. All generators could be used with our ultrasonic transducers, but also with third party transducers.
-
product
Comb Generator
WJ10-25A
Comb Generator model WJ10-25A with Broadband Antenna. Frequency Range 10 MHz - 8 GHz, with two frequencies step size option; 10/25 MHz
-
product
Impulse Generators
HYPERLABS triggerable impulse generators create precise high-speed pulses with 50 to 100 ps rise time. They can be triggered by input from antennas and other signal generator systems.
-
product
Pulse Generators
Pulse generators provide electronic pulses which mimic events from radiation detectors and are useful in set-up, diagnostics, and noise measurement in spectroscopy systems.
-
product
RF Signal Generators
RF Signal Conditioning provides signal manipulation capabilities for high-frequency or broadband signals. You can use these products to augment the capabilities of connected instruments to improve attributes like accuracy and frequency range.
