Filter Results By:
Products
Applications
Manufacturers
Resistors
Keep a steady fixed or variable voltage to current ratio as measured in ohms.
- Pickering Interfaces Inc.
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-034
The 40-297A-034 (PXI) and the 42-297A-034 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Harmonic Filter Resistors
The widespread use of nonlinear loads such as power electronics based equipment and electric arc & ladle melt furnaces all around the world hinder the quality of electric power. One of the most important parameters for defining the power quality is harmonic distortion.
-
product
Dry Dielectric RF Coaxial Loads
4000 Series
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
product
E-Beam Welded Through Hole Shunt Resistors
BWT
These space saving components feature E-Beam welded construction and full RoHS compliancy.
-
product
PXI-2559, 2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module
778572-59
2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module - The PXI‑2559 is a general-purpose switch module featuring two independently terminated single‑pole double‑throw (SPDT) relays. You can use it to add flexibility to your video switch network or to maintain uniform signal paths across multiple channels when building high-channel-count multiplexers. The PXI‑2559 termination resistors minimize reflections on open channels and protect your source or device under test from damage. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
LXI Modular Chassis
Our LXI modular chassis are available in 7-slot or 18-slot and support over 1,000 of our PXI modules, additionally our 2-Slot USB/LXI Chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. These range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of T&M modules such as programmable resistors, digital I/O, power supplies, battery simulators and attenuators.
-
product
Decade Box, Calibrated W/Data, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL D
The 72-7270 CAL D from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
High Voltage Phasing Sticks
9007KB Series
Shanghai Beha Electronics Co., Ltd.
*Important applications include checking voltage fuses, testing for correct phase connections, and for absence of high voltage on deenergized lines or apparatus.*measuring ranges from 6.6kV up to 44kV systems*Fiberglass is of hot stick quality and tested to IEC specs (100kV/300mm for 1 min). All front end (resistors) are encapsulated.
-
product
Voltage Dividers
Measurements International Ltd.
A series of resistors or capacitors which can be tapped at any intermediate point to produce a specific fraction of the voltage applied between its ends.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-020
The 40-297A-020 (PXI) and the 42-297A-020 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
SparkFun Decade Resistance Box
This is the SparkFun Decade Resistance Box, an involved PTH soldering kit that allows you to quickly and accurately dial in a specific resistance value between 0 and 999,990 Ω, in 10 Ω increments. The concept is simple, a decade box is a tool that contains resistors of many values that can be accessed via mechanical switches. All you need to do is just adjust the knobs to output any of the discrete resistances offered by the box. Once assembled, each kit will have controls that correspond to the digits in a decimal number - a control for the tens position, a control for the hundreds position, and so on.
-
product
PXI Resistor Module Quad 8 Bit With 16xSPDT Relays
40-291-121
The 40-290 Series Programmable Resistor Modules comprise a Dual 16-bit or Quad 8-bit resistor chain together with 16 optional SPDT Reed Relays. Connections are made via a front panel SCSI 2 type 68 pin male connector. Programmable resistors may be connected together either in series or in parallel to form many types of configuration.
-
product
Ethernet Digital Interfaces
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
product
Thick Film Passive Element
GBR-395
GBR-395 series high voltage resistors are made in a thick film technology on ceramic substrates(Al2O3 96%). These elements are used in high voltage applications requiring high stability and resistance.
-
product
Resistors
*High Accuracy.*Low Temperature Coefficients.*High Immunity from Environmental Effects.*High Reliability -From 0.01 Ω to 10 MΩ.*By Spetcial orders Only.
-
product
PCI-X Carrier For AMC Modules
PCI102
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
product
PXI Simulation Modules For Sensor Simulation
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-033
The 40-297A-033 (PXI) and the 42-297A-033 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 52.4 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Attenuators
A device consisting of an arrangement of resistors which reduces the strength of a radio or audio signal.
-
product
High Power Precision Current Sensing Resistors
HPCR4T
High Power Precision Current Sensing Resistors of HPCR4T designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow for high precision measurements even with low resistance values. HPCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a cement molding.
-
product
Audio Line Drivers and Receivers
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
product
Resistors
A passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for generators. Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-146
The 40-297A-146 (PXI) and the 42-297A-146 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-013
The 40-297A-013 (PXI) and the 42-297A-013 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
TRC-8542, CAN HS/FD Transceiver Cable
783699-03
The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is … an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
product
CTL503
The CTL503 Curve Tracer is a low-cost transistor (BJT and FET) computer controller curve tracer. Unlike other simple curve tracing units the CTL503 is designed to measure devices to 100V and upto 3A. Four collector resistors (relay selected) allow the user to test the smallest of BJT’s and FET’s as well as extracting meaningful curves from larger TO3/TO247 packaged devices. Limits on both peak test voltage and peak test current can be easily set to prevent exceeding device parameters.Pulse testing (80us/300us) is used to minimise device heating and to ensure the CTL503 can be powered via USB. This may be disabled for smaller parts.Connected and powered via USB and running our own free software the CTL503 is easily configured using a built in wizard (for quick results), or the user can adjust every instrument parameter to suit. Works with EPIC 21.010 and above.Users can save data from runs, as well simply grab images directly from EPIC.Connections are made to the DUT (device-under-test) with the built-in colour coded test leads with crocodile clips.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-051
The 40-297A-051 (PXI) and the 42-297A-051 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
TRC-8542, CAN HS/FD Transceiver Cable
783699-02
CAN HS/FD Transceiver Cable—The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
product
High Voltage Economical Resistors
HVE
The HVE series of high voltage economical resistors feature zero inductance, an excellent range of tolerances, wide resistance values and unparalleled high voltage handling.
-
product
General Purpose 4 Channel Optocoupler Board
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility.
