Filter Results By:
Products
Applications
Manufacturers
Thermal Shock
stress testing by rapidly changing temperature.
See Also: Thermal, Shock, Thermal Test, Thermal Shock Chambers
- Pickering Interfaces Inc.
product
LXI Low Thermal EMF Matrix 1-pole 42x33
60-510-002
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
product
High and Low Temperature Thermal Shock Chamber
HLST-500D
The specimen is placed in test chamber specimen which cannot be placed in high temperature chamber or low temperature chamber. High temperature chamber pre-heats the air and low temperature air chamber pre-cools the air. When doing the test of temperature changing from high to low, the low temperature chamber will blow the pre-cooled air to the test chamber. Then, the air in test chamber will reach your target temperature in several minutes (“recover time”). When doing the test of temperature changing from low to high, the high temperature chamber will blow the pre-heated air to the test chamber. Then the air in test chamber will reach your target temperature within the recover time.
-
product
Small Form Factor Mission Computers
Curtiss-Wright Defense Solutions
Our commercial off-the-shelf (COTS), small form factor (SFF) mission computer systems feature modular, expandable designs that pair powerful graphics and data processing capabilities with ultra-reliable mechanical robustness. The Parvus DuraCOR line of field-tested, MIL-STD qualified mission processors has been proven in the harshest C5ISR applications, performing reliably under thermal, shock, and vibration extremes. We provide application engineering services to extend base system computing functionality for these SFF systems, adding in application-specific I/O and communications cards typically with minimal NRE fees or delivery schedule impact. With pre-integrated, pre-qualified systems tailored by the factory, Parvus DuraCOR customers dramatically reduce scheduling risk and program management overhead, while maximizing use of open architecture COTS technologies. Available in ultra-small, small and standard form factors, we have solutions to meet you SWaP requirements.
-
product
Ground Isolated ICP® Pressure Sensors For High Frequency
PCB® Series 102B is a ground isolated version of the Series 113B. These sensors have all of the same features and benefits of the 113B Series, plus the added benefit of isolation, which helps prevent ground loop problems. This series can accommodate an optional ablative coating (Prefix: CA) to protect the diaphragm from thermal shock in flash-temperature applications.
-
product
Thermal Shock Chamber
Allows for the rapid transfer of products between temperature extremes, or the alternating heating and cooling of test articles in cyclical manner.
-
product
Endevco Cryogenic Charge Output Accelerometers
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
product
Temperature Measurement IR Sensors & Detectors
ST60 High Temperature
A single-channel silicon-based thermopile that will withstand operating temperatures of 225C, with a small active area of 0.61mm x 0.61mm in a TO-5 package. The reduced height package functions as an internal aperture. Two thermistor options provide ambient package temperature measurement. Currently only available with 8-14um silicon window. Time constant of 18ms with Nitrogen encapsulation gas delivers a very low Temperature Coefficient of Responsivity of -0.4%C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Security/Detection
ST120 Dual
A two-channel silicon-based thermopile in a TO-5 package. Each small active area is 1.2mm x 1.2mm . Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Rotary Thermal Shock Chambers
TS Series
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
product
Thermal Shock Testing
Quest Engineering has the capability that you've been seeking to perform thermal shock on a wide array of units. Using our specially designed Thermal Shock Chamber which works like a turnstile to shuttle units between extreme hot and extreme cold conditions.
-
product
Thermal Shock Chamber
The Thermal Shock Chamber is specially designedwith independant temperature zones to facilitatethe automatic transfer of product under testthereby simulating a temperature shock to test the reliability of the product as per military and other international standards.
-
product
Material Test/Cure Rooms
Our walk-in Materials Test and Cure Rooms offer reliable, efficient environmental controls for a variety of applications including shelf-life testing and storage, ceramic and concrete wet and dry cure regimens (including ASTM-compliant units), thermal shock chambers, general, medical and packaging materials.
-
product
Laser Power and Targeting
ST60 Quad
A four-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant four-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Temperature shock test chambers test
TSS series
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
product
Environmental Simulation Testing
Innovative Testing Solutions, Inc.
We have multiple chamber capabilities of simulation most environmental conditions. Our chamber range in capacity from 1 ft3 to 64 ft3 volume. Specialty chambers include air-to-air thermal shock, inert gas injection oven, high/low pressure water spray and direct-injection LN2 chambers.
-
product
Thermal Shock Test Chambers
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 TO-18
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a small TO-18 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Environmental Testing
DATASYST Engineering & Testing Services, Inc.
Simulate real-world environmental conditions to know how your product or component measures up. DATASYST evaluates how your product responds to environmental stressors, including temperature, thermal shock, humidity and altitude.
-
product
Temperature/Humidity Testing
Quest has 14 environmental chambers ranging in size from 1 cubic foot to over 1,000 cubic feet, covering temperatures from below -100C to temperatures exceeding 200C. Our temperature/humidity test chambers include one of the largest walk-in chambers (15 x 10 x 8 ft) in New England, table top, high humidity, thermal shock, and high ramp rate test chambers. We can provide a wide range of temperature/humidity conditions on a variety of different product shapes and sizes, from extremely small to large products.
-
product
Thermal Shock Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
product
Capacitance Standard Frame
AH 1100
The AH 1100 capacitance standard frame containing from one to four AH 11A fused-silica capacitance standards provides reference capacitors of unexcelled stability. The inherent stability of this system when subjected to mechanical or thermal shock makes it the ideal transfer standard for capacitance. The built-in precision temperature controllers make it a simple, reliable system to use.
-
product
Rain Penetration And Thermal Shock Tester
RAST
This is a user-friendly, three-in-one test stand for your operating convenience. Internal and external shock tests as well as rain penetration tests are all important for determining the quality and durability of your products and meeting all relevant international standards.
-
product
Thermal Shock Chambers
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Thermal Shock Chambers are designed for the safe, efficient, and accurate environmental testing of electronics and consumer products, and aerospace, telecommunications, and military and defense components.
-
product
Medium Thermal Shock Chambers
TSD-100
The TSD-100 has our popular touch-screen controller, but with a new feature called Specimen Temperature Trigger (STT). This STT function actively monitors the temperature of the product and only advances the program to the next step once the product has reached the desired temperature. The STT dynamically reduces the overall testing time by adjusting the soak period according to how much product is being tested.
-
-
product
(two/three-zone) Thermal Shock Chambers
TSA Series
Traditional three zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air can be pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
product
Thermal Shock Chamber
Wewon Environmental Chambers Co, Ltd.
Makes it possible to quickly and autonomously transfer test items back and forth repeatedly between a hot and cold environment.
-
product
Liquid Thermal Shock Baths
TSB Series
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
product
Rapid Temperature Change Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Cover temperature,humidity, thermal shock with rapid temperature change rate, vibration testing. The simulation product detects whether the adaptability and characteristics of the product itself have changed under the combined conditions of temperature and humidity in the climate environment (high and low temperature operation & storage, temperature cycle, high temperature and high humidity, low temperature and low humidity, condensation experiment. etc.).
-
product
Temperature Measurement IR Sensors & Detectors
ST120 TO-5
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 1.2mm x 1.2mm in a TO-5 package. Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 With Diffractive Lens
A single-channel silicon-based thermopile with integrated diffractive lens and internal baffle that provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a TO-5 package. Time constant of 18ms with Nitrogen encapsulation gas and a 9 FOV. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
