Filter Results By:
Products
Applications
Manufacturers
-
product
Multi-Cluster Sources
Our complete line of sources can be configured in a Tri-Source configuration. Clustered sources are a vital part of effective seismic exploration. The destructive effects of the air blast associated with a discharging air source are made worse by clustering. In order to maintain the separation between air sources within a cluster, it is necessary to mechanically constrain the sources with rigid bars.
-
product
Destructive Coating Thickness Gauges
Designed for measuring on a non-metallic substrate or assessing the thickness of a multi-coat paint, Elcometer offer a range of destructive coating thickness gauges such as the Elcometer 121/4 and Elcometer 141 that are portable and easy to use.
-
product
Weld Testing
Supports industries such as Aerospace, Nuclear, Automotive, Commercial Fabrication etc.Welding procedure consultancy and approvalWelder qualification test and codingWelding procedure certificationWelder performance qualificationOn site welding invigilationOffers a complete range of destructive and non-destructive testing facilities.Responsible Welding Co-ordinators available for customer supportCAA Weld Specimen SignatoriesCSWIP Approved Inspectors
-
product
Contact Resistance Meter
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
product
Rebar Locator
Profometer PM-600
Profometer PM-600 is an advanced cover meter for the precise and non destructive measurement of concrete cover and rebar diameters and the detection of rebar locations using the eddy current principle with pulse induction as the measuring method.
-
product
Paper Moisture Meters
A paper moisture meter measures the humidity of paper and paper products. Use of a paper moisture meter can prevent costly damages resulting from paper expansion or shrinking. A paper moisture meter determines paper moisture content based on either absolute humidity or relative humidity. Absolute humidity does not take into consideration temperature, while relative humidity relies on temperature and is expressed as a percentage of the total amount of moisture possible at the current temperature. Thus, many paper moisture meter devices feature automatic temperature compensation (ATC).For paper producers, paper manufacturers, paper mills and others in the pulp and paper industry, moisture and humidity control is essential, especially during the production process, as excessive moisture can lead to warming of the paper rolls. A paper moisture meter can be used to detect moisture streaks during the paper production process as well as to identify optimal drying times.Regardless of whether paper is stored in paper rolls in paper converting plants or stacked in sheets and paper bales in commercial printing warehouses, the porous surface of paper gradually takes in moisture relative to the humidity of the surrounding environment. This moisture can be problematic, as too much moisture can cause curling, buckling or the formation of waves in otherwise flat paper products. Moisture also can prevent inks, dyes, paints and coatings from covering and saturating paper properly during printing and processing.PCE Instruments (PCE) offers digital handheld moisture meter devices for measuring the moisture content of paper and paper products such as cardboard, paperboard, corrugated boxes, craft paper, wrapping paper, brown packaging paper, butcher paper, recycled paper, coated paper and more. Different paper moisture meter models utilize different paper moisture measuring techniques, performing moisture content tests of paper products via either destructive or nondestructive methods. Typically, a standard pinless paper moisture meter is nonpenetrating, thus allowing for the nondestructive measurement of paper water content.
-
product
Non Destructive Testing (NDT)
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.
-
product
High speed linear THz camera
High Speed Linear THz camera is our brand new product, which features both, unprecedented imaging speed of 5000 frames per second and ease of integration into any industrial process. Its ultrafast linear sensor array is built to satisfy the needs in Non- Destructive Testing (NDT) and Quality Control (QC) for many industrial applications employing high speed conveyors belts. This product fits most conveyors with a belt speed up to 15 m/s.
-
product
LD/LED ESD Tester
Hanwa Electronic Ind. Co.,Ltd.
◆Automatic operationPerforms automatic destructive evaluation of Lazer-power after zap.After the measurement, the destruction judgment condition can be changed, and it judge again for the acquired data.◆Optical characteristic measurementThe output level of the laser diode (power) is measured by the Photodiode.After zap, it display Optical data displayed(IL), Performs the process of destruction.Settings: slope efficiency, differentiation resistance, and threshold current, etc◆Two kind LDAutomatic settings of two kinds wavelength.◆For variegated deviceThe socket (Jig) is separates. Perform to any device.The P.D. can be changed.Its height can be changed.
-
product
Ion & Electron Detection
Photonis is the global leader in the development and manufacturing of detectors and optical components to detect ions and electrons. These detectors and components have been designed for a wide range of scientific instruments used in space and research projects but also in cells and material analysis in lifescience or non destructive testing.
-
product
Destructive Physical Analysis (DPA)
Is the process of disassembling, testing, and inspecting a component for the purpose of determining conformance with applicable design and process requirements. This process of sample testing is used to ensure that a high reliability component or device is fabricated to the required standards. Destructive Physical Analysis is also used effectively to discover process defects for troublesome production lot problems.
-
product
10KV High Voltage Digital Insulation Resistance Tester
KM 6213AIN
Kusam Electrical Industries Limited
• The KM 6213A IN is the KUSAM-MECO premium model of High Voltage Digital Insulation Resistance Testers.• The KM 6213A IN has new added features with a low consumption High Performance processor.• It displays results much faster and has more advanced features.• The KM 6213A IN has Automatic Polarization Index and Dielectric Absorption Ratio Calculations.• Results are displayed on the new High Contrast LCD. It’s mounting angle makes it more readable for all users, in different working conditions.• The user’s manual reflects the new features and added benefits of this instrument.• It has Auto-Off, Auto-Stop, EnerSave™ and is a non destructive tester.• Once you start the tester, it waits for your selection. You can go up and down in voltage to select the voltage at which you want to test the insulation. Once you have selected that voltage, you need to connect the test leads to the Insulation Tester to measure. Then it measures voltage to ensure there is no voltage present on the equipment under test. If there is a voltage present, it will warn you to disconnect the circuit before proceeding. If it’s free of any voltage, then you can proceed with the testing. This ensures that no damage is done to the Insulation Tester KM 6213AIN.• One of the new innovation on this tester is also the way the new unique calibration process works. It’s fully digital, has no moving parts and does not require expensive and complicated jigs or computers systems to be calibrated. It’s cheaper to maintain than any other Digital HV Insulation tester on the market today. The KM 6213AIN is supplied standard with our Premium test Leads Kit, the AL-50.
-
product
Reach-In Xenon Lamp Weathering Test Chamber
Weiber xenon lamp chamber uses xenon lamp to simulate the whole sunlight spectrum that can produce many destructive effects on the products. This simulation environment provided in the chamber is used to test the resistance of various manufactured products towards these destructive conditions. This chamber is used for quality control, product development and scientific researches and many more. With a variety of models and options, you can customize your chamber to fit your testing needs. Reach in chambers provide a compact testing area for small applications. These are easy to install, transport and occupies less space.
-
product
Hail Impact Testing
Hail is an extremely destructive force of nature, especially for aircraft, with impacts occurring at more than 600 mph. NTS performs hail and stone strike testing and high velocity hail strike testing. These tests can be performed using clear ice, stone and aluminum projectiles of up to two inches in diameter, fired at velocities of up to 741 miles per hour(331.4m/sec, 1087.4 f/sec). Typical test programs include aircraft windshields, antennas, radomes, and wheel/brake assemblies. Using a laser equipped system with a high degree of accuracy, repeatable impacts can be performed to within a quarter inch of the desired target. This accuracy allows NTS to test even the smallest of test samples, as well as limit the potential damage area of larger units.
-
product
Partial Discharge
Partial discharge (PD) is a local electrical discharge that occurs in imperfections or inhomogeneities. The partial discharge measurement is a so-called “non destructive test” to determine the quality of insulating materials. On the contrary of pure high-voltage test, th test item is not pre-damaged at low PD levels.
-
product
12 Channels 1.0 ~ 17.0 Gb/s (200Gbps) Pulse Pattern Generator and Error Detector
CA9806-12
The UC INSTRUEMNTS CA9806-12 is a highp erformance, flexible 12 channels Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (200 G). It is combined with three sets CA9806 4 CH 1.0 to 17.0 Gbps Pulse Pattern Generator and Error Detector that incorporates an external one by 4 rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build-in 8.5 ~ 15 Gb/s eye diagram testing function.
-
product
Short Circuit Test System
Shanghai Guantu Technology Co., Ltd.
The short-circuit test system refers to what kind of short-circuit test is carried out by which equipment, and how long is the test time. But I have one thing to tell you, the short circuit test is a kind of destructive test, mainly to test the working condition of the used equipment in a crisis situation, or to test how strong the anti-destructive ability of the used equipment is. Just like a lot of equipment in the military must undergo a short-circuit test, some for 3 minutes or longer, in order to resist breaking calls against the enemy during wartime.
-
product
Humidity and Temperature
Humidity and Temperature Data Logger DL-200
Non destructive testing / Humidity and Temperature
-
product
Porosity Measurement Tool for the Pharmaceutical Industry
TeraSolve
This module is an addition to the TeraPulse LX product-range. It has been optimized for non- destructive determination of the disintegration and dissolution performance of finished pharmaceutical tablets and other solid dosage forms.
-
product
Wire Crimp Pull Tester (Motorized)
WT3-201M
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
product
Walk-In Xenon Lamp Weathering Test Chamber
Xenon is one of the noble gases and is a major component of arc lamps and flash lamp and it also has its importance in general anesthetics. One of the major applications of xenon lamp is that it can be used in research applications to simulate the sunlight.Weiber walk in xenon lamp chamber uses xenon lamp to simulate the whole sunlight spectrum that can produce many destructive effects on the products. This simulation environment provided in the chamber is used to test the resistance of various manufactured products towards these destructive conditions. This chamber is used for quality control, product development and scientific researches and many more. With a variety of models and options, you can customize your chamber to fit your testing needs. With walk in option you have a facility to test your product in bulk quantity and even for the products which are larger in size. This chamber also known as Uv Test Chamber and Xenon Lamp Weather Resistance Test Chamber.
-
product
Portable Hardness Testers
The UCI hardness measuring method complies to ASTM A1038.The ultrasonic contact impedance (UCI) probe is purposed to be used for hardness measuring in the case of the testing area minimal thickness (from 1 mm), objects of complex surface shape, and for measuring surface hardened layers hardness.This method is very fast and easy: place the probe on the tested object surface, press the probe with the required effort to the surface and save the hardness value, shown on the display of the device. Small size diamond indenter allows measuring hardness value of all items, which are thicker than 1 mm. The UCI method of hardness testing is the least destructive because the hardness tester NOVOTEST T-UD3 with UCI probe leaves much smaller prints (imprints) than the majority of bench hardness tester would. That’s why a portable hardness tester with UCI probe is the best choice.
-
product
Non- Destructive Testing
NDT
Non-destructive testing (NDT) is an application of industrial radiography that uses X-rays to reveal defects in manufactured products or structures. Fujifilm NDT systems share digital X-ray innovations with our Fuji Computed Radiography (FCR) imaging systems.
-
product
Low Voltage Wet Sponge
Operates on a single 9-volt alkaline battery. Unit output voltage is 67.5 volts DC. This voltage makes the detector highly sensitive and accurate. Compact and light weight with no bulky battery packs allowing for non- destructive inspection of paints, epoxy paints and coatings 1-20 Mils.
-
product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
product
Wafer ESD Tester lineup
Hanwa Electronic Ind. Co.,Ltd.
◆Correspond to 300mm Wafer. This tester can measure LED or the large sizes Wafer, such as a system LSI. And Zap of HBM/MM can be performed. The Automatic destructive judging by V/I measurement can also be performed after Zap.◆Waveform guarantee in Zap needles. HED-W5100D carries out the calibration before shipment in the place of Zap needles. Therefore, Correlation of the Result of a Package Device becomes clear easily.◆Correspondence to Standards This Tester corresponds to the Standard of JEITA, ESDA, and JEDEC. A Zap unit adopts the plug-in system and also has the waveform of Customer's requests.◆Connection with TLP This Tester is the best for TLP Testing with deep relation of ESD. The protection circuit of a device with an ESD problem is investigated.
-
product
Component Test and Analysis Laboratories
The Component Test and Analysis team specializes in electronic and mechanical components such as hybrids, connectors, cables, harnesses, passive or discrete components, and digital or linear devices. The test lab has extensive experience in developing test software to electrically and environmentally characterize virtually any integrated circuit, including analog, digital, mixed signal, converters, FPGA and ASICs, as well as experience in developing actual radiation environments for parts testing. The component analysis team offers the analytical expertise and advanced instrumentation to identify root cause explanation for a wide range of component-level failures, as well as the resources to evaluate for possible quality and reliability issues through non-destructive and destructive techniques. With access to a detailed database, the Component Test and Analysis team offers a 25-year history of test and analysis data — a valuable resource for addressing new customer requirements.
-
product
Rebound Hammer
DigiSchmidt - ND
The Schmidt Hammer Digi-Schmidt Type ND was developed for the non destructive measurement of the concrete compressive strength and controlling the uniform concrete quality. Besides showing the basic settings on the included display unit, the Schmidt Hammer offers the transmission of the measured data to a standard printer or to a PC. This supersedes the time consuming business of note taking allowing the user to focus on the essential. The window based software ProVista allows downloading, presenting and editing of the measured values in a fast and easy way.
-
product
Industrial X-Ray
Teledyne DALSA offers powerful, innovative CCD and CMOS X-Ray detectors combining industry-leading performance with cutting-edge features for industrial and scientific applications such as NDT (non destructive testing) in evaluation, troubleshooting, research, and quality control.
-
product
Area Monitors
Provides real-time remote radiological monitoring. Local readout of hand-held meter allows for use as a portable survey instrument. More importantly, since the probe’s sensitive electronics are located far from the high field (25 to 350 feet away), they are not subject to destructive gamma exposure. The probe head may be placed directly into a filter compartment or against a resin tank or waste liner.
