Filter Results By:
Products
Applications
Manufacturers
-
product
Multi-Channel Attenuation Control Unit (5-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7205A
The J7205A is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to5 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205A reduces cost of ownership and provide the best measurement accuracy.
-
product
C-Band / L-Band MWDM
WD1615/C, WD1516/L
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1615/C, WD1516/L WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to EDFA and DWDM network to achieve the combination and separation of C-Band and L-Band.
-
product
Flatness Accessory Kit
55282A
The 55282A Flatness Accessory Kit is composed of an 10759A Footspacing Kit and two 10773A Flatness Mirrors. The footspacing kit provides three precision baseplates, with 50.8 mm (2 in), 101.6 mm (4 in), and 152.4 mm (6 in) pad spacing respectively, that minimize the grid setup and data accumulation time required for plate calibration. The flatness mirrors provide 100 percent reflectance and turn the direction of an incoming laser beam 90 degrees.
-
product
Premium Conductive Rubber Electrode
PRS-801-WV
- Ideal when qualifying or cerftifying material & installation- Each electrode has a resistance of less than 10 ohms- Flatness is measured and delivered within Prostat's specs- Capped to protect the pad against deformation- In accordance with ANSI/ESD S4.1 amd ANSI/ESD S7.1- NIST traceable ceritificate provided for each premium electrode
-
product
SDC-C Series Microwave Downconverter
SDC-C
SDC-C Series Microwave downconverter is a broadband frequency converter that is dedicated for satellite communication. It has a high performance, high reliability and an octave covered by RF signal. Its frequency step is precise and accurate to 1Hz with a variety of IF and signal bandwidth choices. SDC-C series is equipped with functions like self-testing and combination alarm which is suitable for long-time uninterrupted use, guaranteed safety and reliability.SDC-C series microwave downconverter is mainly designed for satellite communication system, signal monitoring system, and electronic countermeasure system with an excellent phase noise, clutter suppression, and in-band flatness data. It is able to provide a transparent RF transmission channel to all videos or data communications. All programming commands can be set through a local panel or through network remotely. SDC-C series microwave downconverter has a standard 2U size.Applications: T&M Systems / Satellite Communications / MIMO
-
product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables
RTM - Measurement Of Positioning Uncertainty Of Indexing Tables
Optik Elektronik Gerätetechnik GmbH
RTM is a software for the measurement of positioning uncertainty of indexing tables using an electronic autocollimator and a polygon mirror as angle reference.
-
product
Attenuators
The 01311 attenuator chip series is designed to achieve precision and tight flatness with an attenuation accuracy of ± 0.2 dB on our 1-10 dB pads and ± 0.3 dB on our 11-20 dB pads. SemiGen tests 100% of all attenuator chips prior to shipment to verify that they meet specifications.
-
product
Multi-Surface Profiler
Tropel® FlatMaster® MSP
The Tropel® FlatMaster® MSP (Multi-Surface Profiler) is a frequency stepping interferometer that provides fast and accurate metrology for semiconductor wafers up to 300mm in diameter. In seconds up to 3 million data points are collected with sub-micron accuracy enabling total thickness and flatness characterization over the entire surface.
-
product
Low Noise Amplifiers
RPG Low Noise Amplifiers are developed and manufactured using the most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 350 GHz. With improved DC-supply and modern semiconductors these amplifiers not only deliver low noise performance but also broad operating bandwidth and gain flatness. These low-noise amplifiers are available as a standard product and on request as customized manufactured product.
-
product
(100×130×19mm) C-Band DWDM Booster EDFA Module
WBA4100-FM04
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM04 series used 100 x 130 x 19mm compact package, is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
product
Testing and Measurement
AkroMetrix provides a variety of products to help you identify and evaluate warpage: For warpage measurements along a production line or at room temperature, AkroMetrix has developed the LineMoiré Production Level Automated Flatness Inspection System. If you need to measure warpage and flatness during pre-defined temperature profiles, AkroMetrix's TherMoiré In-Process Warpage Measurement Systems may fit your requirements.
-
product
Semiconductor Metrology Systems
MTI Instruments'' semiconductor wafer metrology tools consist of a complete line of wafer measurement systems for virtually any material including Silicon wafer (Si), Gallium Arsenide wafer (GaAs), Germanium wafer (Ge) and Indium Phosphide wafer (InP). From manual to semi-automated wafer inspection systems, the Proforma line of wafer metrology inspection tools is ideal for wafer thickness, wafer bow, wafer warp, resistivity, site and global flatness measurement. Our proprietary push/pull capacitance probes provide outstanding accuracy throughout their large measurement range, allowing measurement of highly warped wafers and stacked wafers. MTII''s solar metrology tools include off line manual systems for wafer thickness and Total Thickness Variation (TTV), as well as, in-process measurement systems capable of measuring wafer thickness, TTV and wafer bow at the speed of 5 wafers/second.
-
product
RFoG 4-Band Multiplexer. 1550, 1610 & 1310/1490nm MWDM
WD5643
Hangzhou Huatai Optic Tech. Co., Ltd.
WD5643 WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to FTTx PON network to achieve the combination and separation of the 1550nm (CATV) and 1310/1490nm (data).
-
product
2 Channel Variable Optical Attenuator
S-105
VOA slot module of FOTS system is a module that installs a built-in dual channel MEMS type VOA inside and can do two separate attenuation functions with two each VOA channel being driven individually. This module controls the optical power precisely to maintain the desired output level set by the user by automatically correcting for power drift or fluctuation.This slot module provides high-performance power control features such as high attenuation range, accurate tolerance, stable spectral flatness and low insertion loss in the wavelength range of 1260 ~ 1600 nm. It also offers a particularity that the high-speed drive of attenuation is possible through the combination of high-speed FPGA processor and high speed response time (within 1 ms) VOA. With the provided driving program and GUI, users can set up various attenuation program of each VOA channel such as sequential attenuation step, periodic attenuation and operation time
-
product
Noise Generator
UFX7000
The UFX7000A Series instruments provide Broadband Gaussian noise with superior flatness. The output power can be attenuated up to 127 dB in 1 dB steps, and several connector types are available.
-
product
Mask Flatness Measurement System
Tropel® UltraFlatTM 200 Mask System
The Tropel® UltraFlatTM 200 Mask System was designed specifically for the photomask industry. It delivers the lowest measurement uncertainty for ever-tightening mask flatness specifications. Shrinking device features require not only flatter wafers, but flatter masks.
-
product
Surface Form Analysis System
Tropel® FlatMaster®
Tropel® FlatMaster® Surface Form Analysis System Fast and Precise Measurements of Ground, Lapped, Honed, Polished and Super-finished Components. The Tropel® FlatMaster® offers industry leading performance for surface form measurements to precision component manufacturers. Our non-contact optical technique analyzes the entire surface of the part in seconds, regardless of its size or complexity. The FlatMaster provides five nanometer resolution and a standard accuracy of 50 nm (2.0 μ). It rapidly and accurately measures flatness, line profile, radius and other surface parameters on a variety of materials and surface finishes.
-
product
Active Components
MUD frequency doublers featuring Millitech technology are balanced resistive-mode multipliers covering full waveguide bands. Power flatness for a given input power level for these units is typically ± 2.0 dB across the band.
-
product
Analog Filter
SIM965
Stanford Research Systems, Inc.
The SIM965 Analog Filter is ideal for signal conditioning applications where Bessel or Butterworth filters are needed. Bessel filters offer clean step response (negligible overshoot) and linear phase response, while Butterworth filters provide excellent pass-band flatness with some overshoot
-
product
CATV Booster Optical Amplifier
HA5100
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
product
Preamplifier, 100 MHz to 18 GHz
87405C
Exceptional gain (25 dB) and flatness (1.5 dB) combined with a probe-power bias connection which eliminates the need for an additional DC power supply, makes these preamplifiers the ideal choice for spectrum analyzer or stand alone applications.
-
product
Semiconductor Technology, Micro Scriber + Flatness, Bow, Warp, Curvature, Glass Thickness
FLATSCAN
Optik Elektronik Gerätetechnik GmbH
Non contact automated 2D- or 3D measurement of warp, bow, slope and surface curvature with software module for calculation of thin film stress (wafer stress) of wafers and glass substrates.
-
product
GaN 100W Power Amplifiers
PE15A5033F
The PE15A5033F is a 100 W high gain Class A/AB Coaxial Linear Power Amplifier operating in the 0.7 to 2.7 GHz frequency range. The amplifier offers 100 Watts typical saturated power and 45 dB minimum small signal gain with 1.5 dB typical gain flatness @ Psat. The amplifier requires typically a +30V DC power supply. The SMA connectorized module is unconditionally stable and operates over the temperature range of 0C and +50C. The unit comes with a Heatsink and Fan.
-
product
Individual Optical Filters
Our comprehensive line of Semrock optical filters helps your design attain the best signal-to-noise ratios. Steep spectral edges maximize useable bandwidth, and high transmission or reflection captures the brightest images with best-in-class Flatness. Deep and extended blocking are optimized for your application, minimizing background and crosstalk while reducing cost. Select from the extensive catalog or go with a custom filter to your exact specifications, and remain confident of uncompromising quality, reliability, and reproducible results.
-
product
L-Band Red/Blue-Band Pass MWDM
WD1616/R, WD1616/B
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1616/R, WD1616/B is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to the combination and separation of L-Band, Red-Band (1589~1603nm) and Blue-Band (1570~1584nm).
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
Wafer Flatness Measurement System
FLA-200
*Measures Thickness, TTV, Bow, Warp and site and global Flatness (ASTM compliance)*Measures all materials including Si, GaAs, Ge, InP, SiC*Full 500 micron thickness measurement range without re-*calibration2-D /3-D Mapping software
-
product
Wafer Chucks
ARC, in addition to fabricating Wafer Chucks from aluminum, is also known for its ability to work in hard to machine materials such as hardened (50-62 Rockwell) metal alloys, fired ceramics, e.g. SiC and glasses. These materials are often ideal for semiconductor equipment applications due to their ability to hold critical dimensions and tolerances. ARC specializes in surface grinding and lapping these materials to precision flatness and parallelism specifications needed for semiconductor wafer chuck requirements.
-
product
(125×150×20mm) C-Band DWDM Line EDFA Module
WLA4200-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WLA4200-FM05 series is a gain flatness line EDFA Module which is specifically designed for C-Band 44 channels optic transmission system. It adopts the most excellent optical performance, the most advanced electronic control technology and the most complete software functionalities; it is featured with wide working wavelength range, low noise and excellent gain flatness. WLA4200-FM05 is mainly installed in middle of transmission line, replacing the traditional relay, to compensate the optical power loss in the line and extend the optical signal transmission distance
-
product
1550/1310~1490nm Wavelength Division Multiplexer
PON-WDM-1543
Hangzhou Huatai Optic Tech. Co., Ltd.
PON-WDM-1543 WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to FTTx PON network to achieve the combination and separation of the 1550nm (CATV) and 1310/1490nm (data).
