Filter Results By:
Products
Applications
Manufacturers
Parametric Test
determine whether a DUT's electrical characteristics meet specification.
- InterWorking Labs, Inc.
product
DHCP Tests
The Dynamic Host Configuration Protocol (DHCP) provides configuration parameters to Internet hosts. DHCP consists of two components: a protocol for delivering host-specific configuration parameters from a DHCP server to a host and a mechanism for allocation of network addresses to hosts. DHCP is built on a client-server model, where designated DHCP server hosts allocate network addresses and deliver configuration parameters to dynamically configured hosts. (Source: RFC 2131)
-
product
Test Fixtures & Test Sets
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
product
Common Armament Test Set
MTS-209
The MTS-209 is a state-of-the-art portable test set for various armament systems used on the F-16, F-15, F-18, TA-50, FA-50 and additional aircraft. The MTS-209 supports a wide range of Alternate Mission Equipment (AME) including launchers, pylons, and racks. It combines the test capabilities of an I-Level test set in a compact, rugged, flight-line qualified enclosure. The MTS-209 performs parametric functional tests on AME components including Launchers (LAU-117, 16S210, LAU-127,, LAU-128, LAU-129, LAU-7,etc.), bomb racks (MAU-12, MAU-50, SUU-20, TER-9, etc.), Remote Interface Units (RIUs) and Pylons. The MTS-209 can also test MIL-STD-1760 aircraft stations and weapon systems.
-
product
RF Bias Burn-In System
These systems deliver an unbeatable combination of advantages over a wide range of RF frequencies and power levels. The Automated Multi-Channel RF-Biased Burn-In Test System is a turnkey system that incorporates all of the capability needed for accelerated aging and parametric testing of RF semiconductor devices. Its powerful software elegantly supports data acquisition, storage, and presentation. Accel RF’s customers choose system features to meet their technical needs and capital budget. In addition to cost savings, use of Accel-RF’s solutions accelerate product time-to-market, saving many months of product development.
-
product
Keithley Automated Characterization Suite Software
ACS
Keithley’s Automated Characterization Suite (ACS) is a flexible, interactive software test environment designed for device characterization, parametric test, reliability test, and even simple functional tests. ACS supports a wide array of Keithley instrumentation and systems, hardware configurations, and test settings, from a few bench-top instruments for use in a QA lab to fully integrated and automated rack-based parametric testers. With ACS, users are ready and able to perform tests quickly without the need for programming knowledge.
-
product
Wafer-Level Parametric Test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
product
DC Parametric Test System with Curve Trace
DC3
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
product
PXI Hybrid Single SP6T Switch, DC To 26.5 GHz, Terminated
M9157C
M9157C operates from DC to 26.5 GHz, providing a low-cost operation switching solution for measurement and automation of Automatic Test Equipment (ATE) systems without compromise in the RF performance. It is being used in applications such as ATE, RF communication and RF parametric measurements where a rugged switching module is needed for signal routing. Typical switching applications for multiport coaxial switches include signal routing to a single input to multiple instruments and routing of multiple input signals.
-
product
Probe Card
VC20E Series
The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.
-
product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
EXG Signal Generators
The cost-effective EXG X-Series signal generators address critical speed and uptime needs for manufacturing test. With analog and vector models, the EXG provides the signals you will need for basic parametric testing of components and functional verification of receivers.
-
product
Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
PXI-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
778572-15
35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXI‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXI‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
192 Channel Power Supply
HDPMU
Today cost efficiency is more important than ever. Many manufacturers are working on maximizing multi-site testing. Often maximization can’t be done because of limited tester resources. Salland’s HDPMU gives you up to 192 additional independent parametric measurement units (PMU) channels on a single board. Our solution will increase parallel testing without the need for creating complex device interface board (DIB). It can be used for continuity, functional or parametric tests or simply for device setup or loading. Full integration with the Teradyne IG-XL™ Software, easy set-up and high parallel measurement capability will reduce test costs significantly.
-
product
PXIe Digital Stimulus/Response with PPMU: 250 MHz, 16 Channels
M9195B
The Keysight M9195B PXIe digital stimulus/response (PXI DSR) module is ideal for IC design validation and production test environments. The PXI DSR provides 16 bi-directional digital channels with programmable logic levels and can be configured for synchronized cyclized digital data, for parametric measurements, or for static digital IO.
-
product
DWV/IR Test Systems
When used in conjunction with ART's own parametric relay test systems such as the RT290, the RT900 offers high speed AC and DC Hipot (dielectric withstand voltage) and Leakage testing of relays or other multi-pin passive devices.
-
product
PXI Based Multifunction Measurement and ICT Instrument
PXI-501
The PXI-501 is a multifunction measurement instrument for functional and in-circuit measurements.It combines two parametric measurement units with a digital voltmeter, a high voltage current source and a discharge unit. This powerful combination makes it the ideal instrument for classical analog in-circuit test and manufacturing defect analysis with additional functional test capabilities.With it’s fast sampling rate of up to 4MSps it speeds up measurements and is capable of measuring and generating AC signals up to 100kHz.To enhance the PXI-501 capabilities it can be combined with an ABex TM-501 or an ABex TM-404. The ABex TM-501 enhances the in and output range of the PXI-501. Furthermore, it provides a shunt current measurement upgrade. In combination with the ABex TM-404 it’s a complete in-circuit test solution with 86 channels in one ABex slot. For sure it can be upgraded to 2838 test points in one rack by simply adding additional matrix modules.With the above-mentioned terminal modules, the PXI-501 is able to act as a ABex system controller, so that no additional controller is required in the cassis.
-
product
Full Wafer Test System
FOX-1P
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
product
Stimulus Induced Fault Testing
SIFT
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
-
product
Multi-Wafer Test & Burn-in System
FOX-XP
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
product
256 Channel Power Supply
IDPS750
Salland Engineering’s Independent Device Power Supply (IDPS) can expand your existing Automated Test Equipment (ATE) with up to 256 independent DPS sources to increase parallel testing. It offers Force Voltage (FV) and Measure Current (MI) that can be used for continuity tests, parametric supply current (IDD) and quiescent supply current (IDDQ) measurements or simply for powering devices under test. The IDPS750 is targeted to reduce test costs for a wide range of applications including smart cards, memory, microprocessors and FPGA’s. Its design makes it useful in applications where many resources are required, or were the original ATE supplies do not meet your required specifications.
-
product
Device Power Supply (DPS) & Parametric Measurement Units (PMU) ATE
Analog Devices’ parametric measurement units (PMUs) and device power supply (DPS) products offer a flexible range of voltage and current source/measurement capability to meet the needs of a wide range of cost-sensitive test applications. With a proven track record, Analog Devices’ PMU and DPS products serve a wide variety of precision test application requirements, such as measurement and control for voltage and current. Analog Devices’ DPS and PMU products are equipped with unique precision measurement and control capability for today's demanding ATE solutions.
-
product
Probe Card
VC20E Lab
*20 millimeter ceramic probe card*Optimized for DC parametric test, modeling and characterization, and single site WLR*Can be quickly installed using an interface tool into various interfaces and takes minimal storage space on the test floor*Effective operating temperature range from -65° to 200° C*Leakage as low as 5fA/V. If you require faster settling time, click here*Can be configured with up to 48 probes
-
product
Combination Board Tester
ATE QT2256-640 PXI
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
product
Parametric Test Fixture
U2941A
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
product
Single Event Effects Test System
SEE-RAD
The SEE-RAD test system brings together the proven features of our ETS780 tester (such as true APG memory test and powerful FA tools) with the newest technology of the Griffin III. With all new high-accuracy DC Parametrics, superior precision pin drivers, and capture memory of 64M, the Griffin SEE-RAD combines the newest innovations in the test industry with our years of experience in Radiation Test.
-
product
Digital I/O with Per Channel Timing, Programmable Logic Levels and PMU PXI Card
GX5296
The GX5296 offers the most performance and features of any 3U PXI dynamic digital I/O board on the market today. The 32-channel, GX5296 offers timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability emulate and test complex digital busses for system, board or device test applications. Offering 1 ns edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level).
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
Parametric Test Solutions
Reduce your cost-of-test up to 20% with our ultra-fast CPU Overcome your process test challenges Boost measurement throughput and lower costs with our synchronous/asynchronous parallel test capability Better low-level measurement performance Create customized waveforms Reduce transition costs
