Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
18-Slot LXI Modular Switching Chassis
60-103B-001
This 18-slot LXI Chassis is fully compliant with the LXI Standard 1.4 and allows the large number of our 3U PXI modules to be installed and controlled through a standardized Ethernet interface. Each module is supported as though it is an LXI compliant device, complete with a driverless soft front panel that provides control of the module functions.
-
product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
*ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch*24-port fully managed Gigabit Ethernet switch*Pre-installed ADLINK PacketManager accelerates packet processing*Layer 2/3 switching with advanced support for VLANs, QoS and IPv6*Two 10 Gigabit Ethernet SFP+ uplink ports*Supports IPMI based on PICMG 2.9 (System Management Specification)
-
product
*6U CompactPSB 4-slot SSR FSL 33MHz VIO 5V BW 64-Bit
80965-004-6800
6U CompactPSB Backplane 4-slot, PICMG 2.0 R3.0, system slot right, PICMG 2.16 R1.0 fabric slot left, supports full hot swap function according to PICMG 2.1 R2.0, 1Gb/s Ethernet switching, clock frequency 33MHz, V(I/O) +5V, bus width 64-bit
-
product
LXI Modular Chassis
Our LXI modular chassis are available in 7-slot or 18-slot and support over 1,000 of our PXI modules, additionally our 2-Slot USB/LXI Chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. These range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of T&M modules such as programmable resistors, digital I/O, power supplies, battery simulators and attenuators.
-
product
4-Slot USB/LXI Modular Chassis
60-105-001
This 4-slot USB/LXI modular chassis offers a small lightweight form factor, making it ideal for portable, benchtop, and space restrictive applications. The chassis is designed for desk or rack mounting and features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.
-
product
LXI Optical Switching
LXI is an ideal platform for supporting optical switching systems; the use of Ethernet control makes it easy to provide optical switching within the network that is easy to control via a programmatic or web based interface. MEMS switch technology offers higher performance and longer operational life compared to conventional prism based optical switching.
-
product
High Speed Digital Analog
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
product
6U VME COTS System, Sensor Interface Unit
SIU6
NAI's SIU6 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU6 leverages NAI field-proven, 6U VME boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
product
16-Ch SPST 10A-277VAC High Current
YAV90086
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
product
96-Ch Switching
YAV90064
96 relays SPST, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
PC104 Switches
Curtiss-Wright Defense Solutions
Our PC104 switches provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Fast and Gigabit Ethernet links. These PC/104 Ethernet switches, optimized for size, weight, and power (SWaP)-sensitive embedded military and civilian computer network systems applications, enable reliable local area network (LAN) switching in extended operating temperature ranges and extreme shock/vibration environments. Ideal for connecting computers, cameras, sensors, and command and control equipment, these cards are typically deployed in manned and unmanned system platforms.
-
product
64-Ch 24VDC Switching
YAV90164
64 relays SPDT, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Cables And Connector Solutions
Pickering Interfaces provides a full range of supporting cables and connector solutions for all of our PXI switching and simulation modules, LXI Ethernet switching solutions and PCI switch and simulation cards. We offer everything from simple mating connectors through to complex cables assemblies and terminal blocks.
-
product
32-Ch Switching
YAV90133
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(8×16)-Ch Dual Pole 2A-250VAC Matrix
YAV90060
128 relays DPST double matrix (4×16). Switching up to 250Vac and 2A CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
3U OpenVPX Sensor Interface Unit - SIU36
SIU36
The SIU36 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU36 leverages NAI’s 3U boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
3U OpenVPX Sensor Interface Unit
SIU34
The SIU34 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU34 leverages NAI’s 3U OpenVPX™ boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
PCIe 10G Ethernet Switch
VPX3-663
Curtiss-Wright Defense Solutions
The VPX3-663 hybrid switch combines PCI Express 3.1 and 10 Gigabit Ethernet switching in a single 3U VPX module. Ideal for size, weight, and power (SWaP)-constrained platforms, the VPX3-663 provides single-slot connectivity for high-performance processing systems that combine SBC, DSP, GPU, FPGA, I/O, or storage modules.
-
product
Custom Switch Matrix
- Fully customized switching configurations (from 1x1024 to 24x42)- Universal Power Supply (96-240Vac)- Local Display – High Visibility LED- Standard 19" racks and custom chassis available - Local and/or remote control- 50 and 75 ohm impedances- Multiple interface configurations: - RF ports – SMA, 2.92mm, N, SMB, TNC, etc. - Control – RS-232, Ethernet, USB, Keypad, etc.- Monitor cycle count- Full Command API included- In-circuit programming (firmware upgradable) - Systems can be ruggedized and tested for challenging environments- Passive components Integration (Filters, Attenuators, Dividers, Combiners, etc.)
-
product
Ethernet Switch
SWE440S
The NETernity™ SWE440S is a fully managed (Layer 2/3) 3U VPX Ethernet switch designed to meet the most demanding requirements for network switching in tactical applications. Building on the strong capability and high performance of the SWE440A 3U VPX networking solution, the SWE440S offers the same winning solution and has been designed to align to the SOSA Technical Standard.
-
product
2-Bus Fault Insertion
YAV90077
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
I2C Isolators
Analog Devices’ family of isolated I2C isolators support a complete isolated I2C interface. This portfolio is based on our iCoupler® chip scale transformer technology. iCoupler is a magnetic isolation technology with functional, performance, size, and power consumption advantages compared to optocouplers. By integrating iCoupler channels with semiconductor circuitry, our technology enables a complete, isolated I2C interface with a small form factor. Our I2C isolators covers applications such as central office switching, networking, and power over Ethernet.
-
product
3U OpenVPX Sensor Interface Unit
SIU32S
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
High Current Power Switching
YAV90CIN
12 Independent SPST relays Switching up to 8A 250Vac 12 current measurement channels 8x Sense connections General inhibit input CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Switch & Router Modules
Curtiss-Wright Defense Solutions
Our highly engineered networking cards provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Gigabit, 10 Gigabit, and 40 Gigabit Ethernet. Operating at wire-speed, Ethernet switching and routing can be used to architect the infrastructure for unified (Ethernet only) or hybrid (Ethernet control and other switched data-plane fabric) networks for transferring IP-based control and data packets within advanced military systems.
-
product
High-Speed Digital Switch Matrix & Optical Power Management System
VERTA
Avionics Interface Technologies
Switching & Optical Power Management system supporting Fibre Channel & Ethernet interconnect and power management applications.
-
product
(8×16)-Ch 2A-250VAC 24VDC Matrix
YAV90069
Software configurable for: 1(64×2), 2(32×2), 1(16×2) + 3(16×2). Switching 2A 250Vac. Max switching up to 62.5V CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Multimeter/Data Acquisition/Switch Systems
Keithley 2700
Each Series 2700 system combines precision measurement, switching, and control in a tightly integrated enclosure for either rack-mount or bench-top applications. Although the core functionality and programming of all three systems are identical, each mainframe has unique capabilities. For example, the Model 2701 provides a 10/100BaseTX Ethernet interface, and the Model 2750 offers extended low ohms measurement capability. All models are compatible with the same line of plug-in multiplexer, matrix, or control modules. See all digital multimeters »
-
product
48-Ch Bus Fault Insertion
YAV90076
48 channels 2A 250V 2 Fault Insertion Buses Switching up to 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
