Filter Results By:
Products
Applications
Manufacturers
Serial Digital Interfaces
A family of digital video interfaces standardized by SMPTE.
- TEAM SOLUTIONS, INC.
product
HandyScope HS6-DIFF With SafeGround & SureConnect: 200 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-200XMSG-W5
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.-SureConnect, auto-detects a true connection between the probe tip and the device under test.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71620
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
I²C/SPI Interface Device
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
product
Digital Interface Boards
Model 4863 OEM
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
product
4-Channel 200 MHz A/D with DDC, Kintex UltraScale FPGA - 3U VPX
Model 52861
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-7 FPGA - 6U VPX
Model 58720
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- One or two DUCs (Digital Upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connectionsto the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 3U VPX
Model 52751
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 57610
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
product
CAMERA LEVEL METER
SDI-2
The SDI-2 is a low cost pocket size, digital, hand-held, battery operated meter that measures HD (High Definition) video signals. Use it for fast and accurate set-up and verification of levels and slope-loss on any SDI (Serial Digital Interface) signal. This meter is a must-have for anyone working with HD CCTV cameras or any SDI video signals.
-
product
Small Form Factor Communications Modules
Diamond's line of rugged, wide-temperature Communications Modules feature standard and optoisolated RS-232/422/485 serial interfaces, Ethernet, CAN bus, GPS, and digital I/O functions. We have modules available in the following form factors: PC/104, PC/104-Plus, EMX and PCIe MiniCard.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
Intelligent Power Monitor
iPM
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
product
Light / Lux Meter, Calibrated, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL
The 72-7250 CAL from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - XMC
Model 71821
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range and analog signal integrity- Xilinx® Kintex® UltraScale" FPGA- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of 2400 MHz DDR4 SDRAM- Programmable frequency synthesized sample clock generator- Sample clock synchronization to an external system reference- Powerful DMA controllers for moving data- PCI Express (Gen. 1, 2 & 3) interface up to x8- Multi-channel synchronization with clock/sync bus- Optional clock/sync generator for multi-board systems- Optional LVDS port for custom FPGA I/O- Optional gigabit serial links for custom FPGA I/O- Ruggedized and conduction-cooled versions available- Navigator® BSP for software development- Navigator® FDK for custom IP development- SPARK® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Serial Controlled Relays And Relay Drivers
*ICS's Serial controlled Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Serial to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any Serial programming language. Use ICS's interactive Serial Keyboard program for easy operation from your PC without having to write a program.
-
product
USB OEM Data Acquisition (DAQ) Products
ACCES now offers USB-based data acquisition and control in both standard packaging and embedded OEM USB/104 board only options. These USB devices are perfect for a variety of applications requiring monitoring, control and industrial serial communications. USB is by far the most popular and compatible standard data interface for direct PC connection. Add the features you need in your application in hours, not days. Choose from over 100 different models and options (including extended temperature) encompassing analog I/O, digital I/O, counter/timer, and serial I/O configurations. Experience simple and immediate connection to any PC or embedded system with a USB port.
-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 57741
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1-channel mode with 3.6 GHz, 12-bit A/Ds- Two or four 2-channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one- or twochannel DDCs (Digital Downconverters)- 4 or 8 GB of DDR3 SDRAM- µSync clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface-Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conductioncooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
SDI Reclockers
Macom Technology Solutions Holdings Inc.
MACOM’s reclockers are specifically designed to help build robust video broadcast systems by removing jitter from Serial Digital Interface (SDI) video signals. These multi-rate products are essential when designing high definition (HD) and ultra high-definition (UHD) systems that are compliant with the Society of Motion Picture and Television Engineers (SMPTE) standards.
-
product
Light / Lux Meter, Calibrated w/D & U, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL DU
The 72-7250 CAL DU from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
-
product
Serial To Digital Interface MiniBox™
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 57791
- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
2-Channel 3.6 GHz or 4-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 58641
- Ideal radar and software radio interface solution- Two 1-Channel mode with 3.6 GHz, 12-bit A/Ds- Four 2-Channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one-channel DDC (digital downconverter)- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
RF Prototyping Kit
VXI-5501
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
product
Digital Automation System
DA-10
The DA-10 Theatre Automation has an onboard serial port for connection to serial-style digital cinema servers like the Dolby Show Store. It has an onboard GPIO interface for connection to GPIO-style digital cinema servers like the Doremi DCP-2000 and GDC SA-2100.
-
product
8-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 58671
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 1.25 GHz 16-bit D/As- Eight digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Quad µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Networked Absolute Inclinometer
T7
The T7 is available in several interface and protocol options. The physical interface can be RS232, RS485 or US Digital's CAN (Controller Area Network). The protocol can be either US Digital's serial protocol or Modbus RTU. The RS232 version supports a single T7 with up to 100 ft of cable. For users that need longer cable lengths or multiple T7s on a single bus, the RS485 or US Digital CAN (Controller Area Network) version can be used. The USD-CAN protocol allows a network of up to sixty-four T7s to be connected to a single host. Power for each T7 is supplied over the CAN network cable. The host accesses the USD-CAN T7s through US Digital's low cost CANA-232/CANA-485 adapter module. This module allows the host to access each T7 on the network using simple, easy serial port commands, just like the RS232 version. The RS485 version supports up to 32 T7s on the bus.
-
product
Extension Module
GE-DIO-42
Infinite Industrial Informatics Lt
GE-DIO-42 is a digital I/O, DIN rail mount expansion module with I2C serial communication interface. It can be used for the analog input expansion of Infinite's products as the SCOM-100 GSM controller and the iLOGPlus RTU/Data Logger.
-
product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 58851
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUC (digital upconverter)- Four 800 MHz 16-bit D/As- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 57641
- Ideal radar and software radio interface solution- One 1-Channel mode with 3.6 GHz, 12-bit A/Ds- Two 2-Channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one-channel DDC (digital downconverter)- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
