Filter Results By:
Products
Applications
Manufacturers
RF Sources
Produce Radio Frequency (RF) signal.
- Pickering Interfaces Inc.
product
PXI/PXIe RF Matrix, 8x2, 1GHz, 50Ω, SMB
40-750A-511
The 40-750A-511 (PXI) and 42-750A-511 (PXIe) are 50 Ω 8x2 RF matrix modules with SMB connectors suitable for switching frequencies up to 1000 MHz. They are part of a range of 8x2 matrix modules with 50 Ω or 75 Ω characteristic impedance with front panel mounted SMA, SMB or MS-M multiway coaxial connectors.
-
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Frequency Shaped Isotropic Electric Probes
PI-SH-FCC, PI-SH-ICNIRP
An isotropic electric field probe with shaped frequency response meeting the ICNIRP or FCC RF safety standards for occupational and general public exposure limits (see the specified frequency ranges below). Meter readings are shown in % of the STD – standard reference level, eliminating the need to know the source frequency. Probe output is proportional to RF power density in the whole specified power range, producing the correct RF power measurements in single and multi-signal environments, typically present at multiple antenna sites.
-
product
High Power RF-Signal Generators
Becker Nachrichtentechnik GmbH
Multi channel RF signal sources with precise high power output levels. Each output offers a separate, analogue level control. This ensures highest precision in level during a long term usage.
-
product
Bandpass Filters
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
product
Level System
Universal II
The Universal II level transmitter offers increased reliability, low maintenance and an intrinsically safe design for dependable level measurements in all kinds of process liquids, slurries, granulars and interfaces.Universal IIThe Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.When powered from an approved source this level transmitter can be made intrinsically safe. Its rugged contruction resists corrosion and abraision. The no moving parts design eliminates break downs.The Universal II level transmitter utilizes RF Admittance technology with manual calibration and a 4 – 20 mA output signal. The patented Cote-Shield circuitry ensures accuracy and reliability regardless of product build-up on the level transmitter.This level system is unaffected by changes in the process material density, pressure, or temperature variations.
-
product
Multi-Channel Signal Generator
S1000 & IZT S1010
One Unit - 31 Signal Generators. Multi-Channel Signal Generator for I/Q data, Sirius, XM, HD Radio, AM, FM, DAB/+, DVB-T and DRM/+. The IZT S1000 Signal Generator Platform enables the user to consolidate multiple conventional RF generators into one compact, cost effective, flexible, and easy-to-use RF test source.
-
product
SGMA RF Source
SGS100A
The R&S®SGS100A is an RF source designed to meet the requirements of automated test systems. It is available as a CW source or as a vector signal generator with an integrated I/Q modulator. With its frequency range of up to 12.75 GHz, the vector signal generation version covers the essential digital signals. The CW version can be used as a flexible local oscillator and for interference testing against mobile radio standards.
-
product
Active Differential Probe, 100 kHz to 12 GHz
U1818B
The Keysight U1818B 100 kHz to 12 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818B allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
Ettus USRP X410, 1 MHz to 7.2 GHz, 400 MHz Bandwidth, GPS-Disciplined OCXO, USRP Software Defined Radio Device
787272-01
The Ettus USRP X410 integrates hardware and software to help you prototype high-performance wireless systems and perform over-the-air signal generation and analysis. Additionally, the Ettus USRP X410 features a two-stage superheterodyne architecture with four independent transmitter and receiver channels. It also features a Xilinx Zynq Ultrascale+ RFSoC with programmable FPGA supporting the Open Source UHD tool flow as well as LabVIEW FPGA. With these features, the Ettus USRP X410 has the RF and processing performance for applications such as wireless communications prototyping, spectrum monitoring, and signals intelligence. The Ettus USRP X410 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
product
RF Calibration Accessories
Employing good connector practice when using an RF calibrator not only avoids measurement errors and minimizes connector repeatability uncertainties but also reduces risk of damage to connectors and equipment. The 96000CONN and 9600CONN connector kits include a range of adapters and torque wrenches intended for use with the 96000 Series RF Reference Sources (9600CONN for the 96040A and 96000CONN for the 96270).The 9600CONN connector kit includes one each of 50 Ω and 75 N-Type male-female adapter for use with the 96000 Series levelling head as a “connector saver” or “sacrificial connector” to avoid risk of damage when making connections to UUT/DUT instruments.
-
product
SSA-X Signal Source Analyzer, 1 MHz To 8 GHz
E5055A
The Keysight E5055A SSA-X signal source analyzer provides precise and accurate measurements in one box. Comprehensive and versatile, this solution evaluates the phase noise and other relevant parameters for RF signals up to 8 GHz. Flexible measurement settings and a modern user interface improve measurement efficiency, while application support through software expands measurement coverage to meet new requirements.
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (m) 50 Ohm
CK520A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (f) 50 Ohm
CK519A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
RF Conducted Immunity Test System
RFCI61000-4-6
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
product
MP field sources calibration set
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
product
Handheld Broadband Noise Generator
NS-1
The Model NS-1 is a handheld broadband white Gaussian noise source. It generates a wide, even, RF noise-signal. The NS-1 is popular for testing network components and aligning a building's coaxial cable network. The NS-1's noise-signal is also used to provide the RF source for measuring insertion loss of cable, splitters, taps and more.
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (f) 50 Ohm
CK521A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Power Limiter, 5 MHz to 6 GHz, Type-N
11930B
The Keysight 11930B limiter provides input protection for a variety of RF and microwave instrumentation. Failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage. The Keysight 11930B provides the same protection to spectrum analyzers and sources. At even greater power levels, failure mode for limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
product
Aerospace & Defense
Electronic warfare (EW) systems require advanced high-fidelity threat simulators to prepare for combat with potential adversaries. Hiller Measurements’ depth of knowledge in RF source and measurement technologies enables us to help our clients develop the best EW simulation systems that will meet the everchanging landscape of EW threat simulation.
-
product
Filtered AC Interface Module
AC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of AC power.
-
product
Digital RF Power &VSWR Measurement System
PowerMaster II
Thank you for purchasing the Array Solutions PowerMaster II RFPower/VSWR Indicator. The PowerMaster II represents a breakthrough in features for measurement of the performance of your transmitting system. Microprocessor control insures fast capture time and low power consumption. With the ability to monitor your VSWR and power levels at all times, you will know that your transmitter, RF source, and load, or antenna systems are operating effectively and safely. In addition, the power and VSWR relay alarms can quickly shut down your power amplifier system and alert you to the alarm condition. This places an additional layer of protection in your transmitting system to help preserve expensive tubes and finals. The PowerMaster II also features the ability to be monitored and controlled from a PC using the software downloadable from our website, and the unique ability to be monitored and controlled over a LAN or from the internet. PowerMaster II firmware updates will be posted for download from the Array Solutions website as they become available. This means that the user can take full advantageof features or enhancements just by installing the firmware update. No need to return the meter to the factory for updates
-
product
USB Controlled RF Signal Generators
Windfreak Technologies provides high value radio frequency devices such as RF Signal Generators, RF Synthesizers, RF Network Analyzers, RF Power Detectors, RF Mixers, and RF Frequency Converters. These devices can be used as RF Test and Measurement Equipment and controlled by Labview in an Automated Test Equipment (ATE) setup, or used as bolt-in RF modules in RF communications equipment. All products have innovative, powerful feature sets controlled by internal microprocessors so any settings can be memorized and used with or without a PC. Windfreak hardware also comes with the Labview GUI source code saving the end user hundreds of hours programming custom software. Use one of our RF Signal Generators or other products risk free. Return it if you dont like it.
-
product
RF Direction Finding, Localization And Interference Hunting
Handheld RF direction finding signal analyzers are ideal for tracing accidental, illegal, or deliberate interference or potentially dangerous signal sources.
-
product
Filtered DC Interface Module
DC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of DC power.
-
product
All-In-One Infotainment RF Signal Source
AST-1000
The software-defined AST-1000 is powered by Averna’s RF and test expertise, enabling you to generate all common radio signals (e.g., AM/FM, HD Radio and Sirius/XM), digital video signals (e.g., ATSC, CMMB and DVB-T2), and simulate all common GNSS signals (e.g., BeiDou, Galileo and GPS).
-
product
RF Detectors for Millimeter Wave
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
product
RF And Microwave Signal Generation And Analysis
The need for microwave test and measurement technology is even more urgent than the need for microwave equipment itself. Therefore, Shengbo Technology is relying on its own research and development capabilities to strive to become one of the comprehensive microwave test and measurement equipment suppliers. We provide a wide range of RF microwave test products, including a good-quality full-band broadband up-down converter . You can provide 2GHz real-time bandwidth signal up-down conversion function in the frequency range of 0.1 ~ 40 + GHz. With our channel simulator , we Became the first company in the world to provide channel analog solutions in such a wide range of broadband signals. At the same time, we are also an innovativesupplier of noise sources and multi-channel microwave signal sources in the industry.
-
product
PCI Direct Digital Synthesizers
SYNTH300 SERIES
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.Software support for Windows Vista, Windows XP,Linux and Labview source code availableFor detailed specifications, please refer to the Synth300_Manual
-
product
PXI-2555, 2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-55
2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2555 is an RF signal multiplexer switch module. The internal termination of the PXI‑2555, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in video RF applications where such reflections can damage the source. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
