Filter Results By:
Products
Applications
Manufacturers
SPI
assures volume and area of paste application.
-
product
VVDI Programmer
MC9S08 series secured and unsecured , MC68 HC series (9) 12 secured and unsecured, MC9S12 series secured and unsecuredV850 series, H8X series, R8C series, R5F series, PCF79XX, EEPROM SPI, I2C, & mu WIRE, PIC 12F, 16F, 18F, Infineon TRICORE, Infineon XC2xxxx, Infineon XC164CS, ST10F series, ST7 series, STM8 series, ATMEL- Atmega 8, 48, 16, 32, 64, 128, 256, MPC560 series, SPC560 series, Fujitsu MB91F
-
product
Tactical Grade Inertial Measurement Unit (IMU)
ADIS16490 iSensor
The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
USB Protocol Analyzers
Beagle Series
Our line of Beagle Protocol Analyzers provide real-time visibility into I2C, SPI, and USB systems making them ideal tools for embedded engineers.The Beagle analyzers provide high-performance bus monitoring in a small, portable package that includes cross-platform software support making it perfect for engineers in the field and in the lab.
-
product
CyberOptics SE Series
SE Series
The CyberOptics SE Series offers the most accurate and repeatable, high speed 3D solder paste inspection in the market today. Utilizing the most advanced sensing technology, CyberOptics SPI products will provide manufacturers the reliability needed to compliment your overall screen print process improvement strategy.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-T
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Interface Adapter
U2C-12
Dimax U2C-12, all-in-one USB-I2C, USB-SPI and USB-GPIO Bridge device, converts PC USB transactions to the I2C Master, SPI Master transactions and GPIO functions. U2C-12 turns your PC running Windows, Linux or MacOS into comprehensive I2C/SPI Bus master.
-
product
SOM Module
TEO820-ZU2CG
Sundance Multiprocessor Technology Ltd.
Xilinx Zynq UltraScale+ XCZU2CG-1SFVC784EZU2, 784 Pin Packages4 x 5 cm form factorRugged for shock and high vibration2 x 512 MByte 32-Bit width DDR4 SDRAM2 x 32 MByte (2 x 256 MBit) SPI Boot Flash dual parallel4 GByte eMMC Memory (up to 64 GByte)B2B Connectors: 2 x 100 Pin and 1 x 60 Pin
-
product
Embedded Serial Triggering and Analysis for InfiniiVision DSOX1000 Series Oscilloscopes
DSOX1EMBD
The IC, SPI, and UART/RS-232 serial decode option for InfiniiVision 1000 X-Series oscilloscopes (DSO models) displays responsive, time-aligned, on-screen decode of Inter-Integrated Circuit (IC), 3-wire Serial Peripheral Interface (SPI), and UART/RS232 serial communication buses. Because it is hardware-based, this option provides the fastest throughput solution for triggering on and analyzing IC, SPI and UART/RS-232 serial buses found in a wide variety of embedded designs.
-
product
SparkFun MicroSD Transflash Breakout
Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested.
-
product
Relay Test Set Type SP-I
Supreme Instrument Laboratories
Supreme make relay testing set is designed for site testing of protective relays which simulate in common fault conditions under which a protective relay will be called into positive function. Periodic field testing is the best way of ensuring the integrity of the protective relays. We offer our relay testing set with specific testing capacity to suit different group of protective relays. The testing set operates on single phase 230 V, A.C. 50Hz. Supply.
-
product
Logic Analyzer
LAP-321000U-A
Zeroplus Technology Corperation
Sample rate (Internal clock): 200MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Memory Depth (per channel): 1MbitsChannels: 32CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals. Glitch Capture Capability: 5ns. Bandwidth: 75MHz.
-
product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
product
72 channel FPGA Logic Module
XLM72
XLM72 is a FPGA based logic module with 72 I/O ports. Featuring two 64 Mbit SPI (Serial Peripheral Interface) memories, from one of which its FPGA boots upon power-up, complex logic operations can be programmed and saved on-board.
-
product
Block Up-Converter
BUC Series 5” x 2.5” x 0.6”
*Connectorized Package *Compact, Rugged Design *C, X, Ku, K, and Ka-Bands Available *L-Band Inputs (950-2150 MHz) *Internal or External Filters Available *Variable Attenuation Control via CAN +5V Logic, SPI, RS232, or I²C
-
product
COM Express Type 7
ROM-8720
Advantech ROM-8720 COM Express Type 7 Compact Computer-on-Module is powered by NXP LS1046A SoC which includes four Arm Cortex-A72 cores for Edge networking and Edge firewall, two 10Gbsp-KR and up to four Gbps for the networking communications. Three PCIe, three USB 3.2 Gen1 and three USB2.0 for the embedded interface expansions. two UART, one SPI and 8 GPIO for embedded device controls.
-
product
Low speed Serial Interfaces
12C/ 12S/ SPI/ UART
Arasan has a diverse portfolio of connectivity IP products including SPI, I2C, I2S and UART. These protocols are vital for the integration of SoCs with peripheral chipsets in order to form a complete hardware platform. They are frequently used by the SoC to configure, control and gather diagnostic information at the platform level to ensure correct operation of the hardware.Arasan's proven Connectivity IP Solutions provides a risk free path to integrating these interfaces in SoC designs:High quality IP cores ensure inter-operability between SoCs and peripheralsIn-house domain expertise ensures a high quality support throughout the SoC development cycleTotal IP solution includes RTL source code, synthesis scripts, test environment and documentation
-
product
SparkFun MicroMod GNSS Carrier Board (ZED-F9P)
With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters, and that's why we had to put it on this board! With the flexibility of the MicroMod's M.2 connector, you can easily test and swap out different MicroMod processor boards for your application. Simply match up the key on your board's beveled edge connector to the key on the M.2 connector and secure the boards with a screw. This means solderless access to the ZED-F9P modules features via UART1, UART2, SPI, and I2C ports!
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
3D SPI Series
MS-11e
- Exclusive15MP / 25MP CoaXPress Camera System- Dual Projection Shadow Free Moiré Technology- Precision Compound Telecentric Camera Lens- Automated Z-Height Calibration System- Automated PCB Under Board Support System- Precision PCB Warpage Compensation- Closed Loop Communication With Screen Printer- Absolute Repeatability and Reproducibility- INTELLISYS® Industry 4.0 Intelligent Factory Automation System
-
product
Module Spectrum
nRF52810 Series
Nordic nRF52810 solutioin features an Arm Cortex-M4 processor with 192 KB Flash and 24 KB RAM with 32 GPIO available. Supports SPI, UART, I2C, PWM interfaces with both Chip Antenna and PCB Antenna option for selection.
-
product
InfiniiVision Oscilloscopes
2000 X-Series
70 MHz to 200 MHz See more signal detail with 50,000 wfms/s update rateView time-correlated digital content with 8 digital channels (MSO)Modulate signals within the scope with WaveGen, built-in 20 MHz function generator (optional)Quickly characterize signals with the built-in 3-digit voltmeter and 5-digit counter option Decode serial busses faster with hardware-based serial analysis options for CAN, LIN, I2C, SPI and RS232/422/485/UART Protect your investment with full upgradability
-
product
Digital Temperature Sensors
Analog Devices offers a broad selection of digital temperature sensors with I2C, SPI, and mark space interfaces. For more intricate system design applications, some of these sensors have integrated D/A converters, A/D converters, references, and limit alarm register. All of these sensors possess a broad range of uses, including scientific, medical, and aerospace applications, in test and measurement equipment, and in industrial automation.
-
product
Multiplying Current Output D/A Converters
Analog Devices offers a wide range of high precision, multiplying current output (IOUT) D/A converters (DACs) that feature ±1 LSB INL and DNL specifications, from 12-bit up to an industry-leading 18-bit resolution. Our portfolio includes single and multiple D/A converters in small packages with parallel or serial SPI interfaces. Multiplying current output R-2R D/A converters allow for an external amplifier that’s optimized for specific applications and that does not require reference buffering, which enables high linearity. The SoftSpan™ feature allows software selectable output spans, therefore eliminating the need to add precision gain stages and the associated external jumpers, precision resistors, and amplifier circuitry. Integrated precision resistors allow for reference inversion, bipolar offset, and offset and gain adjustment.
-
product
Dual Projection 3D In-Line Solder Inspection System
KY8030-2
The new KY8030-2 delivers 2x fasterinspection without compromising performanceand accuracy.Using patented dual projection, the systemeliminates the critical Shadow problem thatall 3D SPI systems can be vulnerable to.Easy UI and SPC Plus are included in the systempackage in order to help users achieve faster& easier printer process optimization
-
product
Solder Paste Inspection System
LaserVision SP3D Mini
The LaserVision SP3D Mini offers the same level of overall measurement capabilities as the VisionPro SP3D. Utilizing a lower cost microscope platform and the ability for customers to supply their own PC if needed, the SP3D Mini sets the "affordable" boundary on reliable, low cost SPI solutions.
-
product
Logic Analyzer & Digital Pattern Generator
ScanaQuad Series
ScanaQuad (SQ) is a series of high performance 4 channels logic analyzers and digital pattern generators. They are designed to be your best companion when working on serial protocols like UART, SPI, I2C, 1-Wire, USB, I2S, CAN, LIN, RS232, RS485, and more. With ScanaQuad Logic Analyzers, you can capture signals, you can play them back, and you can even build genuine test signals and generate them!
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-K
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Arduino CAN Shield
IFB-10003-INP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Serial I/O Boards
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
