AcQ International
We develop, produce and deliver innovative solutions for a wide range of real-time electronics platforms used in the aerospace, military, industrial automation, transportation, agriculture and space sectors.
- +31 (0)412 641922
- 31 412 622 640
- info@acq.nl
- Alanenweg 6
5342 PV Oss
, 5347
Netherlands, Kingdom of the
-
product
RTD Measurement for CompactPCI
CPCI390
The CPCI390 has a 3U form factor and features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm limit checking. Sensordata is available in °C, °F, K and Ohm. All inputs are optically isolated from the system.
-
product
Quadrature Incremental Decoder Interface for VMEbus
VME323
The VME323 is an Intelligent Quadrature Incremental Decoder VMEbus Board which can be configured for interfacing quadrature incremental encoders with or without an index channel. In index mode up to sixteen encoders with two quadrature channels and an index channel can be connected, and in non-index mode up to twentyfour encoders with two quadrature channels can be connected. The VME323 operates on two encoder input channels and decodes a pair of out-of phase signals in order to increment or decrement a counter.
-
product
VPX
VPX, formerly known as VITA 46, is an ANSI standard (ANSI/VITA 46.0-2007) that provides VMEbus-based systems with support for switched fabrics over a new high speed connector.
-
product
RTD Measurement for VMEbus
VME390
The VME390 features 24 two, three or four wire high-accuracy PT100 measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued.
-
product
M-Module Carrier for CompactPCI (3U)
i3002
The i3002 provides a high-performance CompactPCI bus gateway to the M-module interface. The i3002 has a 3U form factor. Two M-modules can be mounted on the i3002. The M-module interface of the i3002 complies with the M-module specification. The M-module interface feature A8, A24, D16 and D32 access types.
-
product
Stepper Motor Controller for PCI
PCI321
The PCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.
-
product
M-Modules
M-Modules are a mezzanine standard mainly used in industrial computers. Being mezzanines, they are always plugged on a carrier PCB that supports this format. M-Modules are standardized as ANSI/VITA 12-1996 and are especially suited for adding any kind of real-world I/O to a system in a flexible way.
-
product
64 Channel ADC for VMEbus
VME392
The VME392 features 64 self-contained ADC channels with a resolution of either 12 or 16-bit (see ordering information). This product is ideally suited for mass acquisition with high accuracy for reasonable cost. The 64 channels are grouped into four sections of 16 channels each. Each section behaves completely independent from the other sections.
-
product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
product
Aerospace
AcQ can perform custom developments compliant with ED12/DO-178B and ED80/DO-254 in various design assurance levels (DALs) for safety critical applications, using the ED14/DO160 for the environmental requirements. AcQ also offers standard products for various open standards like VMEbus, CPCI, PCI and other bus standards for test applications and other applications like GPS, display, actuators, data logging and -storage.
-
product
CANbus Controller
CPCI360
The CPCI360 CANbus controller is a 3U CompactPCI card based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier messages. Front LEDs provide diagnostic information.
-
product
8 Channel ADC for PCI
PCI393
The PCI393 8-Channel Differential Input ADC for PCI is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs all functionality and user-specific functions can be added for customized operation.
-
product
12-/16-bit 16 Channel DAC for CompactPCI
CPCI395
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
product
CANbus Controller Standard Interface
PCI360
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
product
16 Channel ADC for CompactPCI
CPCI392
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
