Megger Group Ltd.
Megger has been a leader in electrical test and measurement globally for 130 years. From power generation to the power outlets in your home, Megger products cover almost every application within the Electrical Supply Industry.
- +44 (0) 1304 502101
- uksales@megger.com
- Archcliffe Road
Dover, CT17 9EN
United Kingdom of Great Britain and Northern Ireland
-
product
Transformer Insulation Testing
The primary test methods used to assess the condition of the active insulation components in transformers and bushings, on site, include:1) power factor/tan δ,2) variable frequency power factor/tan δ (1 - 500 Hz)3) dielectric frequency response (DFR) [a dielectric response method], and4) moisture in oil measurements (for transformers).
-
product
Multifunction Installation Testers
Megger multifunction installation testers are capable of performing various electrical tests.
-
product
Cable Route Tracing and Identification
Cable pinpointers and fault locators from Megger make the process of cable route tracing and identification quicker and more accurate. These pinpointing systems are portable for everyday fieldwork and provide services from power and telecoms to water, rail and gas utilities. HV and LV buried cables can be traced to a depth of up to 5m.
-
-
product
Cable Fault Locating Equipment
Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.
-
product
Contact Resistance Test Sets
When a high current passes through a pair of mechanically independent metallic contacts, the resistance must be as low as possible. An increase in resistance can lead to additional degradation, as I2R losses will cause local heating of the contact surfaces. Our range of micro-ohmmeters measure both steady state and dynamic low resistance values. With test currents up to 600A available, logging and trending are also available on some models. We ensure that our Contact Resistance tests sets are portable, making them suitable for field measurements. Our contact resistance testers’ portability makes them ideal for a vast range of resistance testing across the entire LV, MV HV and EHV spectrum.
-
product
Resistance, Ground Testing, Battery And Power Quality
Our testing equipment works wherever you are, whenever you need it, with precision and reliability.
-
product
DC Overvoltage or Withstand Testing
Overvoltage protection is critical to the long-term health of any cable. DC overvoltage testing (also known as withstand testing) is the most popular method of general condition and integrity assessment in the power, industrial and domestic markets. This method of testing is distinguished a number of key advantages:
-
product
Oil Tan Delta Test Set
The Oil Tan Delta (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. Megger has developed features of the OTD to ensure that productivity levels within laboratories are maximised. OTD test sets are supplied with sixteen standard test sequences pre-installed, to support a set of international standards.
-
product
UHF PD Detector
Handheld online PD substation surveying system. The UHF PD Detector is the ideal tool for quick, non-invasive surveys in MV and HV substations and should be part of the toolkit for all maintenance and service teams. Due to its high measurement bandwidth, the UHF method provides accurate local online partial discharge (PD) measurements on HV components such as cable end-terminations, surge arrestors, voltage transformers and isolators.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Electricians' Accessories
A selection of voltage detectors, proving units, test leads, certificate books and a DVD, which make it that bit safer and easier to get the job done.
-
product
VLF Insulation Testing
VLF testing uses very low frequencies as part of an AC cable maintenance routine. VLF testers are smaller and more practical than AC testers but output the same amount of power as a 50 Hz mains device. This combination of size and power makes Very Low Frequency cable testing perfect for testing longer sections of cable and apparatus
-
product
Insulation Testing
Measures the total resistance between any two points separated by electrical insulation.
-
product
Low Resistance Or Continuity Testing
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
Children
-
STATES®
STATES® Terminal Blocks and Test Switches are designed and manufactured by Megger to facilitate the calibration, disconnecting, troubleshooting, checkout and testing of meters, relays, instruments, transducers and control systems.
Children
-
SebaKMT
Worldwide, we are the leading company for the development and manufacture or measurement equipment for diagnosis of the state of a network and for fault location. Our sectors of the market include electricity supply networks as well as communications and pipe networks. A member of Megger Group.
Children
-
Power Diagnostix Systems GmbH
Power Diagnostix offers instruments for partial discharge (PD) measurement and monitoring (ICM™ Technology), loss factor (LF/DF) measurement devices, fiber optic analog and digital signal transmission systems, high voltage test and control systems and cabinets, plus many other tools for high voltage diagnostic applications.
